1 /*
2 * winbond-cir.c - Driver for the Consumer IR functionality of Winbond
3 * SuperI/O chips.
4 *
5 * Currently supports the Winbond WPCD376i chip (PNP id WEC1022), but
6 * could probably support others (Winbond WEC102X, NatSemi, etc)
7 * with minor modifications.
8 *
9 * Original Author: David Härdeman <david@hardeman.nu>
10 * Copyright (C) 2012 Sean Young <sean@mess.org>
11 * Copyright (C) 2009 - 2011 David Härdeman <david@hardeman.nu>
12 *
13 * Dedicated to my daughter Matilda, without whose loving attention this
14 * driver would have been finished in half the time and with a fraction
15 * of the bugs.
16 *
17 * Written using:
18 * o Winbond WPCD376I datasheet helpfully provided by Jesse Barnes at Intel
19 * o NatSemi PC87338/PC97338 datasheet (for the serial port stuff)
20 * o DSDT dumps
21 *
22 * Supported features:
23 * o IR Receive
24 * o IR Transmit
25 * o Wake-On-CIR functionality
26 * o Carrier detection
27 *
28 * This program is free software; you can redistribute it and/or modify
29 * it under the terms of the GNU General Public License as published by
30 * the Free Software Foundation; either version 2 of the License, or
31 * (at your option) any later version.
32 *
33 * This program is distributed in the hope that it will be useful,
34 * but WITHOUT ANY WARRANTY; without even the implied warranty of
35 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
36 * GNU General Public License for more details.
37 */
38
39 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
40
41 #include <linux/module.h>
42 #include <linux/pnp.h>
43 #include <linux/interrupt.h>
44 #include <linux/timer.h>
45 #include <linux/leds.h>
46 #include <linux/spinlock.h>
47 #include <linux/pci_ids.h>
48 #include <linux/io.h>
49 #include <linux/bitrev.h>
50 #include <linux/slab.h>
51 #include <linux/wait.h>
52 #include <linux/sched.h>
53 #include <media/rc-core.h>
54
55 #define DRVNAME "winbond-cir"
56
57 /* CEIR Wake-Up Registers, relative to data->wbase */
58 #define WBCIR_REG_WCEIR_CTL 0x03 /* CEIR Receiver Control */
59 #define WBCIR_REG_WCEIR_STS 0x04 /* CEIR Receiver Status */
60 #define WBCIR_REG_WCEIR_EV_EN 0x05 /* CEIR Receiver Event Enable */
61 #define WBCIR_REG_WCEIR_CNTL 0x06 /* CEIR Receiver Counter Low */
62 #define WBCIR_REG_WCEIR_CNTH 0x07 /* CEIR Receiver Counter High */
63 #define WBCIR_REG_WCEIR_INDEX 0x08 /* CEIR Receiver Index */
64 #define WBCIR_REG_WCEIR_DATA 0x09 /* CEIR Receiver Data */
65 #define WBCIR_REG_WCEIR_CSL 0x0A /* CEIR Re. Compare Strlen */
66 #define WBCIR_REG_WCEIR_CFG1 0x0B /* CEIR Re. Configuration 1 */
67 #define WBCIR_REG_WCEIR_CFG2 0x0C /* CEIR Re. Configuration 2 */
68
69 /* CEIR Enhanced Functionality Registers, relative to data->ebase */
70 #define WBCIR_REG_ECEIR_CTS 0x00 /* Enhanced IR Control Status */
71 #define WBCIR_REG_ECEIR_CCTL 0x01 /* Infrared Counter Control */
72 #define WBCIR_REG_ECEIR_CNT_LO 0x02 /* Infrared Counter LSB */
73 #define WBCIR_REG_ECEIR_CNT_HI 0x03 /* Infrared Counter MSB */
74 #define WBCIR_REG_ECEIR_IREM 0x04 /* Infrared Emitter Status */
75
76 /* SP3 Banked Registers, relative to data->sbase */
77 #define WBCIR_REG_SP3_BSR 0x03 /* Bank Select, all banks */
78 /* Bank 0 */
79 #define WBCIR_REG_SP3_RXDATA 0x00 /* FIFO RX data (r) */
80 #define WBCIR_REG_SP3_TXDATA 0x00 /* FIFO TX data (w) */
81 #define WBCIR_REG_SP3_IER 0x01 /* Interrupt Enable */
82 #define WBCIR_REG_SP3_EIR 0x02 /* Event Identification (r) */
83 #define WBCIR_REG_SP3_FCR 0x02 /* FIFO Control (w) */
84 #define WBCIR_REG_SP3_MCR 0x04 /* Mode Control */
85 #define WBCIR_REG_SP3_LSR 0x05 /* Link Status */
86 #define WBCIR_REG_SP3_MSR 0x06 /* Modem Status */
87 #define WBCIR_REG_SP3_ASCR 0x07 /* Aux Status and Control */
88 /* Bank 2 */
89 #define WBCIR_REG_SP3_BGDL 0x00 /* Baud Divisor LSB */
90 #define WBCIR_REG_SP3_BGDH 0x01 /* Baud Divisor MSB */
91 #define WBCIR_REG_SP3_EXCR1 0x02 /* Extended Control 1 */
92 #define WBCIR_REG_SP3_EXCR2 0x04 /* Extended Control 2 */
93 #define WBCIR_REG_SP3_TXFLV 0x06 /* TX FIFO Level */
94 #define WBCIR_REG_SP3_RXFLV 0x07 /* RX FIFO Level */
95 /* Bank 3 */
96 #define WBCIR_REG_SP3_MRID 0x00 /* Module Identification */
97 #define WBCIR_REG_SP3_SH_LCR 0x01 /* LCR Shadow */
98 #define WBCIR_REG_SP3_SH_FCR 0x02 /* FCR Shadow */
99 /* Bank 4 */
100 #define WBCIR_REG_SP3_IRCR1 0x02 /* Infrared Control 1 */
101 /* Bank 5 */
102 #define WBCIR_REG_SP3_IRCR2 0x04 /* Infrared Control 2 */
103 /* Bank 6 */
104 #define WBCIR_REG_SP3_IRCR3 0x00 /* Infrared Control 3 */
105 #define WBCIR_REG_SP3_SIR_PW 0x02 /* SIR Pulse Width */
106 /* Bank 7 */
107 #define WBCIR_REG_SP3_IRRXDC 0x00 /* IR RX Demod Control */
108 #define WBCIR_REG_SP3_IRTXMC 0x01 /* IR TX Mod Control */
109 #define WBCIR_REG_SP3_RCCFG 0x02 /* CEIR Config */
110 #define WBCIR_REG_SP3_IRCFG1 0x04 /* Infrared Config 1 */
111 #define WBCIR_REG_SP3_IRCFG4 0x07 /* Infrared Config 4 */
112
113 /*
114 * Magic values follow
115 */
116
117 /* No interrupts for WBCIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */
118 #define WBCIR_IRQ_NONE 0x00
119 /* RX data bit for WBCIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */
120 #define WBCIR_IRQ_RX 0x01
121 /* TX data low bit for WBCIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */
122 #define WBCIR_IRQ_TX_LOW 0x02
123 /* Over/Under-flow bit for WBCIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */
124 #define WBCIR_IRQ_ERR 0x04
125 /* TX data empty bit for WBCEIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */
126 #define WBCIR_IRQ_TX_EMPTY 0x20
127 /* Led enable/disable bit for WBCIR_REG_ECEIR_CTS */
128 #define WBCIR_LED_ENABLE 0x80
129 /* RX data available bit for WBCIR_REG_SP3_LSR */
130 #define WBCIR_RX_AVAIL 0x01
131 /* RX data overrun error bit for WBCIR_REG_SP3_LSR */
132 #define WBCIR_RX_OVERRUN 0x02
133 /* TX End-Of-Transmission bit for WBCIR_REG_SP3_ASCR */
134 #define WBCIR_TX_EOT 0x04
135 /* RX disable bit for WBCIR_REG_SP3_ASCR */
136 #define WBCIR_RX_DISABLE 0x20
137 /* TX data underrun error bit for WBCIR_REG_SP3_ASCR */
138 #define WBCIR_TX_UNDERRUN 0x40
139 /* Extended mode enable bit for WBCIR_REG_SP3_EXCR1 */
140 #define WBCIR_EXT_ENABLE 0x01
141 /* Select compare register in WBCIR_REG_WCEIR_INDEX (bits 5 & 6) */
142 #define WBCIR_REGSEL_COMPARE 0x10
143 /* Select mask register in WBCIR_REG_WCEIR_INDEX (bits 5 & 6) */
144 #define WBCIR_REGSEL_MASK 0x20
145 /* Starting address of selected register in WBCIR_REG_WCEIR_INDEX */
146 #define WBCIR_REG_ADDR0 0x00
147 /* Enable carrier counter */
148 #define WBCIR_CNTR_EN 0x01
149 /* Reset carrier counter */
150 #define WBCIR_CNTR_R 0x02
151 /* Invert TX */
152 #define WBCIR_IRTX_INV 0x04
153 /* Receiver oversampling */
154 #define WBCIR_RX_T_OV 0x40
155
156 /* Valid banks for the SP3 UART */
157 enum wbcir_bank {
158 WBCIR_BANK_0 = 0x00,
159 WBCIR_BANK_1 = 0x80,
160 WBCIR_BANK_2 = 0xE0,
161 WBCIR_BANK_3 = 0xE4,
162 WBCIR_BANK_4 = 0xE8,
163 WBCIR_BANK_5 = 0xEC,
164 WBCIR_BANK_6 = 0xF0,
165 WBCIR_BANK_7 = 0xF4,
166 };
167
168 /* Supported power-on IR Protocols */
169 enum wbcir_protocol {
170 IR_PROTOCOL_RC5 = 0x0,
171 IR_PROTOCOL_NEC = 0x1,
172 IR_PROTOCOL_RC6 = 0x2,
173 };
174
175 /* Possible states for IR reception */
176 enum wbcir_rxstate {
177 WBCIR_RXSTATE_INACTIVE = 0,
178 WBCIR_RXSTATE_ACTIVE,
179 WBCIR_RXSTATE_ERROR
180 };
181
182 /* Possible states for IR transmission */
183 enum wbcir_txstate {
184 WBCIR_TXSTATE_INACTIVE = 0,
185 WBCIR_TXSTATE_ACTIVE,
186 WBCIR_TXSTATE_ERROR
187 };
188
189 /* Misc */
190 #define WBCIR_NAME "Winbond CIR"
191 #define WBCIR_ID_FAMILY 0xF1 /* Family ID for the WPCD376I */
192 #define WBCIR_ID_CHIP 0x04 /* Chip ID for the WPCD376I */
193 #define WAKEUP_IOMEM_LEN 0x10 /* Wake-Up I/O Reg Len */
194 #define EHFUNC_IOMEM_LEN 0x10 /* Enhanced Func I/O Reg Len */
195 #define SP_IOMEM_LEN 0x08 /* Serial Port 3 (IR) Reg Len */
196
197 /* Per-device data */
198 struct wbcir_data {
199 spinlock_t spinlock;
200 struct rc_dev *dev;
201 struct led_classdev led;
202
203 unsigned long wbase; /* Wake-Up Baseaddr */
204 unsigned long ebase; /* Enhanced Func. Baseaddr */
205 unsigned long sbase; /* Serial Port Baseaddr */
206 unsigned int irq; /* Serial Port IRQ */
207 u8 irqmask;
208
209 /* RX state */
210 enum wbcir_rxstate rxstate;
211 int carrier_report_enabled;
212 u32 pulse_duration;
213
214 /* TX state */
215 enum wbcir_txstate txstate;
216 u32 txlen;
217 u32 txoff;
218 u32 *txbuf;
219 u8 txmask;
220 u32 txcarrier;
221 };
222
223 static bool invert; /* default = 0 */
224 module_param(invert, bool, 0444);
225 MODULE_PARM_DESC(invert, "Invert the signal from the IR receiver");
226
227 static bool txandrx; /* default = 0 */
228 module_param(txandrx, bool, 0444);
229 MODULE_PARM_DESC(txandrx, "Allow simultaneous TX and RX");
230
231
232 /*****************************************************************************
233 *
234 * UTILITY FUNCTIONS
235 *
236 *****************************************************************************/
237
238 /* Caller needs to hold wbcir_lock */
239 static void
wbcir_set_bits(unsigned long addr,u8 bits,u8 mask)240 wbcir_set_bits(unsigned long addr, u8 bits, u8 mask)
241 {
242 u8 val;
243
244 val = inb(addr);
245 val = ((val & ~mask) | (bits & mask));
246 outb(val, addr);
247 }
248
249 /* Selects the register bank for the serial port */
250 static inline void
wbcir_select_bank(struct wbcir_data * data,enum wbcir_bank bank)251 wbcir_select_bank(struct wbcir_data *data, enum wbcir_bank bank)
252 {
253 outb(bank, data->sbase + WBCIR_REG_SP3_BSR);
254 }
255
256 static inline void
wbcir_set_irqmask(struct wbcir_data * data,u8 irqmask)257 wbcir_set_irqmask(struct wbcir_data *data, u8 irqmask)
258 {
259 if (data->irqmask == irqmask)
260 return;
261
262 wbcir_select_bank(data, WBCIR_BANK_0);
263 outb(irqmask, data->sbase + WBCIR_REG_SP3_IER);
264 data->irqmask = irqmask;
265 }
266
267 static enum led_brightness
wbcir_led_brightness_get(struct led_classdev * led_cdev)268 wbcir_led_brightness_get(struct led_classdev *led_cdev)
269 {
270 struct wbcir_data *data = container_of(led_cdev,
271 struct wbcir_data,
272 led);
273
274 if (inb(data->ebase + WBCIR_REG_ECEIR_CTS) & WBCIR_LED_ENABLE)
275 return LED_FULL;
276 else
277 return LED_OFF;
278 }
279
280 static void
wbcir_led_brightness_set(struct led_classdev * led_cdev,enum led_brightness brightness)281 wbcir_led_brightness_set(struct led_classdev *led_cdev,
282 enum led_brightness brightness)
283 {
284 struct wbcir_data *data = container_of(led_cdev,
285 struct wbcir_data,
286 led);
287
288 wbcir_set_bits(data->ebase + WBCIR_REG_ECEIR_CTS,
289 brightness == LED_OFF ? 0x00 : WBCIR_LED_ENABLE,
290 WBCIR_LED_ENABLE);
291 }
292
293 /* Manchester encodes bits to RC6 message cells (see wbcir_shutdown) */
294 static u8
wbcir_to_rc6cells(u8 val)295 wbcir_to_rc6cells(u8 val)
296 {
297 u8 coded = 0x00;
298 int i;
299
300 val &= 0x0F;
301 for (i = 0; i < 4; i++) {
302 if (val & 0x01)
303 coded |= 0x02 << (i * 2);
304 else
305 coded |= 0x01 << (i * 2);
306 val >>= 1;
307 }
308
309 return coded;
310 }
311
312 /*****************************************************************************
313 *
314 * INTERRUPT FUNCTIONS
315 *
316 *****************************************************************************/
317
318 static void
wbcir_carrier_report(struct wbcir_data * data)319 wbcir_carrier_report(struct wbcir_data *data)
320 {
321 unsigned counter = inb(data->ebase + WBCIR_REG_ECEIR_CNT_LO) |
322 inb(data->ebase + WBCIR_REG_ECEIR_CNT_HI) << 8;
323
324 if (counter > 0 && counter < 0xffff) {
325 DEFINE_IR_RAW_EVENT(ev);
326
327 ev.carrier_report = 1;
328 ev.carrier = DIV_ROUND_CLOSEST(counter * 1000000u,
329 data->pulse_duration);
330
331 ir_raw_event_store(data->dev, &ev);
332 }
333
334 /* reset and restart the counter */
335 data->pulse_duration = 0;
336 wbcir_set_bits(data->ebase + WBCIR_REG_ECEIR_CCTL, WBCIR_CNTR_R,
337 WBCIR_CNTR_EN | WBCIR_CNTR_R);
338 wbcir_set_bits(data->ebase + WBCIR_REG_ECEIR_CCTL, WBCIR_CNTR_EN,
339 WBCIR_CNTR_EN | WBCIR_CNTR_R);
340 }
341
342 static void
wbcir_idle_rx(struct rc_dev * dev,bool idle)343 wbcir_idle_rx(struct rc_dev *dev, bool idle)
344 {
345 struct wbcir_data *data = dev->priv;
346
347 if (!idle && data->rxstate == WBCIR_RXSTATE_INACTIVE)
348 data->rxstate = WBCIR_RXSTATE_ACTIVE;
349
350 if (idle && data->rxstate != WBCIR_RXSTATE_INACTIVE) {
351 data->rxstate = WBCIR_RXSTATE_INACTIVE;
352
353 if (data->carrier_report_enabled)
354 wbcir_carrier_report(data);
355
356 /* Tell hardware to go idle by setting RXINACTIVE */
357 outb(WBCIR_RX_DISABLE, data->sbase + WBCIR_REG_SP3_ASCR);
358 }
359 }
360
361 static void
wbcir_irq_rx(struct wbcir_data * data,struct pnp_dev * device)362 wbcir_irq_rx(struct wbcir_data *data, struct pnp_dev *device)
363 {
364 u8 irdata;
365 DEFINE_IR_RAW_EVENT(rawir);
366 unsigned duration;
367
368 /* Since RXHDLEV is set, at least 8 bytes are in the FIFO */
369 while (inb(data->sbase + WBCIR_REG_SP3_LSR) & WBCIR_RX_AVAIL) {
370 irdata = inb(data->sbase + WBCIR_REG_SP3_RXDATA);
371 if (data->rxstate == WBCIR_RXSTATE_ERROR)
372 continue;
373
374 duration = ((irdata & 0x7F) + 1) *
375 (data->carrier_report_enabled ? 2 : 10);
376 rawir.pulse = irdata & 0x80 ? false : true;
377 rawir.duration = US_TO_NS(duration);
378
379 if (rawir.pulse)
380 data->pulse_duration += duration;
381
382 ir_raw_event_store_with_filter(data->dev, &rawir);
383 }
384
385 ir_raw_event_handle(data->dev);
386 }
387
388 static void
wbcir_irq_tx(struct wbcir_data * data)389 wbcir_irq_tx(struct wbcir_data *data)
390 {
391 unsigned int space;
392 unsigned int used;
393 u8 bytes[16];
394 u8 byte;
395
396 if (!data->txbuf)
397 return;
398
399 switch (data->txstate) {
400 case WBCIR_TXSTATE_INACTIVE:
401 /* TX FIFO empty */
402 space = 16;
403 break;
404 case WBCIR_TXSTATE_ACTIVE:
405 /* TX FIFO low (3 bytes or less) */
406 space = 13;
407 break;
408 case WBCIR_TXSTATE_ERROR:
409 space = 0;
410 break;
411 default:
412 return;
413 }
414
415 /*
416 * TX data is run-length coded in bytes: YXXXXXXX
417 * Y = space (1) or pulse (0)
418 * X = duration, encoded as (X + 1) * 10us (i.e 10 to 1280 us)
419 */
420 for (used = 0; used < space && data->txoff != data->txlen; used++) {
421 if (data->txbuf[data->txoff] == 0) {
422 data->txoff++;
423 continue;
424 }
425 byte = min((u32)0x80, data->txbuf[data->txoff]);
426 data->txbuf[data->txoff] -= byte;
427 byte--;
428 byte |= (data->txoff % 2 ? 0x80 : 0x00); /* pulse/space */
429 bytes[used] = byte;
430 }
431
432 while (data->txoff != data->txlen && data->txbuf[data->txoff] == 0)
433 data->txoff++;
434
435 if (used == 0) {
436 /* Finished */
437 if (data->txstate == WBCIR_TXSTATE_ERROR)
438 /* Clear TX underrun bit */
439 outb(WBCIR_TX_UNDERRUN, data->sbase + WBCIR_REG_SP3_ASCR);
440 wbcir_set_irqmask(data, WBCIR_IRQ_RX | WBCIR_IRQ_ERR);
441 kfree(data->txbuf);
442 data->txbuf = NULL;
443 data->txstate = WBCIR_TXSTATE_INACTIVE;
444 } else if (data->txoff == data->txlen) {
445 /* At the end of transmission, tell the hw before last byte */
446 outsb(data->sbase + WBCIR_REG_SP3_TXDATA, bytes, used - 1);
447 outb(WBCIR_TX_EOT, data->sbase + WBCIR_REG_SP3_ASCR);
448 outb(bytes[used - 1], data->sbase + WBCIR_REG_SP3_TXDATA);
449 wbcir_set_irqmask(data, WBCIR_IRQ_RX | WBCIR_IRQ_ERR |
450 WBCIR_IRQ_TX_EMPTY);
451 } else {
452 /* More data to follow... */
453 outsb(data->sbase + WBCIR_REG_SP3_RXDATA, bytes, used);
454 if (data->txstate == WBCIR_TXSTATE_INACTIVE) {
455 wbcir_set_irqmask(data, WBCIR_IRQ_RX | WBCIR_IRQ_ERR |
456 WBCIR_IRQ_TX_LOW);
457 data->txstate = WBCIR_TXSTATE_ACTIVE;
458 }
459 }
460 }
461
462 static irqreturn_t
wbcir_irq_handler(int irqno,void * cookie)463 wbcir_irq_handler(int irqno, void *cookie)
464 {
465 struct pnp_dev *device = cookie;
466 struct wbcir_data *data = pnp_get_drvdata(device);
467 unsigned long flags;
468 u8 status;
469
470 spin_lock_irqsave(&data->spinlock, flags);
471 wbcir_select_bank(data, WBCIR_BANK_0);
472 status = inb(data->sbase + WBCIR_REG_SP3_EIR);
473 status &= data->irqmask;
474
475 if (!status) {
476 spin_unlock_irqrestore(&data->spinlock, flags);
477 return IRQ_NONE;
478 }
479
480 if (status & WBCIR_IRQ_ERR) {
481 /* RX overflow? (read clears bit) */
482 if (inb(data->sbase + WBCIR_REG_SP3_LSR) & WBCIR_RX_OVERRUN) {
483 data->rxstate = WBCIR_RXSTATE_ERROR;
484 ir_raw_event_reset(data->dev);
485 }
486
487 /* TX underflow? */
488 if (inb(data->sbase + WBCIR_REG_SP3_ASCR) & WBCIR_TX_UNDERRUN)
489 data->txstate = WBCIR_TXSTATE_ERROR;
490 }
491
492 if (status & WBCIR_IRQ_RX)
493 wbcir_irq_rx(data, device);
494
495 if (status & (WBCIR_IRQ_TX_LOW | WBCIR_IRQ_TX_EMPTY))
496 wbcir_irq_tx(data);
497
498 spin_unlock_irqrestore(&data->spinlock, flags);
499 return IRQ_HANDLED;
500 }
501
502 /*****************************************************************************
503 *
504 * RC-CORE INTERFACE FUNCTIONS
505 *
506 *****************************************************************************/
507
508 static int
wbcir_set_carrier_report(struct rc_dev * dev,int enable)509 wbcir_set_carrier_report(struct rc_dev *dev, int enable)
510 {
511 struct wbcir_data *data = dev->priv;
512 unsigned long flags;
513
514 spin_lock_irqsave(&data->spinlock, flags);
515
516 if (data->carrier_report_enabled == enable) {
517 spin_unlock_irqrestore(&data->spinlock, flags);
518 return 0;
519 }
520
521 data->pulse_duration = 0;
522 wbcir_set_bits(data->ebase + WBCIR_REG_ECEIR_CCTL, WBCIR_CNTR_R,
523 WBCIR_CNTR_EN | WBCIR_CNTR_R);
524
525 if (enable && data->dev->idle)
526 wbcir_set_bits(data->ebase + WBCIR_REG_ECEIR_CCTL,
527 WBCIR_CNTR_EN, WBCIR_CNTR_EN | WBCIR_CNTR_R);
528
529 /* Set a higher sampling resolution if carrier reports are enabled */
530 wbcir_select_bank(data, WBCIR_BANK_2);
531 data->dev->rx_resolution = US_TO_NS(enable ? 2 : 10);
532 outb(enable ? 0x03 : 0x0f, data->sbase + WBCIR_REG_SP3_BGDL);
533 outb(0x00, data->sbase + WBCIR_REG_SP3_BGDH);
534
535 /* Enable oversampling if carrier reports are enabled */
536 wbcir_select_bank(data, WBCIR_BANK_7);
537 wbcir_set_bits(data->sbase + WBCIR_REG_SP3_RCCFG,
538 enable ? WBCIR_RX_T_OV : 0, WBCIR_RX_T_OV);
539
540 data->carrier_report_enabled = enable;
541 spin_unlock_irqrestore(&data->spinlock, flags);
542
543 return 0;
544 }
545
546 static int
wbcir_txcarrier(struct rc_dev * dev,u32 carrier)547 wbcir_txcarrier(struct rc_dev *dev, u32 carrier)
548 {
549 struct wbcir_data *data = dev->priv;
550 unsigned long flags;
551 u8 val;
552 u32 freq;
553
554 freq = DIV_ROUND_CLOSEST(carrier, 1000);
555 if (freq < 30 || freq > 60)
556 return -EINVAL;
557
558 switch (freq) {
559 case 58:
560 case 59:
561 case 60:
562 val = freq - 58;
563 freq *= 1000;
564 break;
565 case 57:
566 val = freq - 27;
567 freq = 56900;
568 break;
569 default:
570 val = freq - 27;
571 freq *= 1000;
572 break;
573 }
574
575 spin_lock_irqsave(&data->spinlock, flags);
576 if (data->txstate != WBCIR_TXSTATE_INACTIVE) {
577 spin_unlock_irqrestore(&data->spinlock, flags);
578 return -EBUSY;
579 }
580
581 if (data->txcarrier != freq) {
582 wbcir_select_bank(data, WBCIR_BANK_7);
583 wbcir_set_bits(data->sbase + WBCIR_REG_SP3_IRTXMC, val, 0x1F);
584 data->txcarrier = freq;
585 }
586
587 spin_unlock_irqrestore(&data->spinlock, flags);
588 return 0;
589 }
590
591 static int
wbcir_txmask(struct rc_dev * dev,u32 mask)592 wbcir_txmask(struct rc_dev *dev, u32 mask)
593 {
594 struct wbcir_data *data = dev->priv;
595 unsigned long flags;
596 u8 val;
597
598 /* return the number of transmitters */
599 if (mask > 15)
600 return 4;
601
602 /* Four outputs, only one output can be enabled at a time */
603 switch (mask) {
604 case 0x1:
605 val = 0x0;
606 break;
607 case 0x2:
608 val = 0x1;
609 break;
610 case 0x4:
611 val = 0x2;
612 break;
613 case 0x8:
614 val = 0x3;
615 break;
616 default:
617 return -EINVAL;
618 }
619
620 spin_lock_irqsave(&data->spinlock, flags);
621 if (data->txstate != WBCIR_TXSTATE_INACTIVE) {
622 spin_unlock_irqrestore(&data->spinlock, flags);
623 return -EBUSY;
624 }
625
626 if (data->txmask != mask) {
627 wbcir_set_bits(data->ebase + WBCIR_REG_ECEIR_CTS, val, 0x0c);
628 data->txmask = mask;
629 }
630
631 spin_unlock_irqrestore(&data->spinlock, flags);
632 return 0;
633 }
634
635 static int
wbcir_tx(struct rc_dev * dev,unsigned * b,unsigned count)636 wbcir_tx(struct rc_dev *dev, unsigned *b, unsigned count)
637 {
638 struct wbcir_data *data = dev->priv;
639 unsigned *buf;
640 unsigned i;
641 unsigned long flags;
642
643 buf = kmalloc_array(count, sizeof(*b), GFP_KERNEL);
644 if (!buf)
645 return -ENOMEM;
646
647 /* Convert values to multiples of 10us */
648 for (i = 0; i < count; i++)
649 buf[i] = DIV_ROUND_CLOSEST(b[i], 10);
650
651 /* Not sure if this is possible, but better safe than sorry */
652 spin_lock_irqsave(&data->spinlock, flags);
653 if (data->txstate != WBCIR_TXSTATE_INACTIVE) {
654 spin_unlock_irqrestore(&data->spinlock, flags);
655 kfree(buf);
656 return -EBUSY;
657 }
658
659 /* Fill the TX fifo once, the irq handler will do the rest */
660 data->txbuf = buf;
661 data->txlen = count;
662 data->txoff = 0;
663 wbcir_irq_tx(data);
664
665 /* We're done */
666 spin_unlock_irqrestore(&data->spinlock, flags);
667 return count;
668 }
669
670 /*****************************************************************************
671 *
672 * SETUP/INIT/SUSPEND/RESUME FUNCTIONS
673 *
674 *****************************************************************************/
675
676 static void
wbcir_shutdown(struct pnp_dev * device)677 wbcir_shutdown(struct pnp_dev *device)
678 {
679 struct device *dev = &device->dev;
680 struct wbcir_data *data = pnp_get_drvdata(device);
681 struct rc_dev *rc = data->dev;
682 bool do_wake = true;
683 u8 match[11];
684 u8 mask[11];
685 u8 rc6_csl = 0;
686 u8 proto;
687 u32 wake_sc = rc->scancode_wakeup_filter.data;
688 u32 mask_sc = rc->scancode_wakeup_filter.mask;
689 int i;
690
691 memset(match, 0, sizeof(match));
692 memset(mask, 0, sizeof(mask));
693
694 if (!mask_sc || !device_may_wakeup(dev)) {
695 do_wake = false;
696 goto finish;
697 }
698
699 switch (rc->wakeup_protocol) {
700 case RC_PROTO_RC5:
701 /* Mask = 13 bits, ex toggle */
702 mask[0] = (mask_sc & 0x003f);
703 mask[0] |= (mask_sc & 0x0300) >> 2;
704 mask[1] = (mask_sc & 0x1c00) >> 10;
705 if (mask_sc & 0x0040) /* 2nd start bit */
706 match[1] |= 0x10;
707
708 match[0] = (wake_sc & 0x003F); /* 6 command bits */
709 match[0] |= (wake_sc & 0x0300) >> 2; /* 2 address bits */
710 match[1] = (wake_sc & 0x1c00) >> 10; /* 3 address bits */
711 if (!(wake_sc & 0x0040)) /* 2nd start bit */
712 match[1] |= 0x10;
713
714 proto = IR_PROTOCOL_RC5;
715 break;
716
717 case RC_PROTO_NEC:
718 mask[1] = bitrev8(mask_sc);
719 mask[0] = mask[1];
720 mask[3] = bitrev8(mask_sc >> 8);
721 mask[2] = mask[3];
722
723 match[1] = bitrev8(wake_sc);
724 match[0] = ~match[1];
725 match[3] = bitrev8(wake_sc >> 8);
726 match[2] = ~match[3];
727
728 proto = IR_PROTOCOL_NEC;
729 break;
730
731 case RC_PROTO_NECX:
732 mask[1] = bitrev8(mask_sc);
733 mask[0] = mask[1];
734 mask[2] = bitrev8(mask_sc >> 8);
735 mask[3] = bitrev8(mask_sc >> 16);
736
737 match[1] = bitrev8(wake_sc);
738 match[0] = ~match[1];
739 match[2] = bitrev8(wake_sc >> 8);
740 match[3] = bitrev8(wake_sc >> 16);
741
742 proto = IR_PROTOCOL_NEC;
743 break;
744
745 case RC_PROTO_NEC32:
746 mask[0] = bitrev8(mask_sc);
747 mask[1] = bitrev8(mask_sc >> 8);
748 mask[2] = bitrev8(mask_sc >> 16);
749 mask[3] = bitrev8(mask_sc >> 24);
750
751 match[0] = bitrev8(wake_sc);
752 match[1] = bitrev8(wake_sc >> 8);
753 match[2] = bitrev8(wake_sc >> 16);
754 match[3] = bitrev8(wake_sc >> 24);
755
756 proto = IR_PROTOCOL_NEC;
757 break;
758
759 case RC_PROTO_RC6_0:
760 /* Command */
761 match[0] = wbcir_to_rc6cells(wake_sc >> 0);
762 mask[0] = wbcir_to_rc6cells(mask_sc >> 0);
763 match[1] = wbcir_to_rc6cells(wake_sc >> 4);
764 mask[1] = wbcir_to_rc6cells(mask_sc >> 4);
765
766 /* Address */
767 match[2] = wbcir_to_rc6cells(wake_sc >> 8);
768 mask[2] = wbcir_to_rc6cells(mask_sc >> 8);
769 match[3] = wbcir_to_rc6cells(wake_sc >> 12);
770 mask[3] = wbcir_to_rc6cells(mask_sc >> 12);
771
772 /* Header */
773 match[4] = 0x50; /* mode1 = mode0 = 0, ignore toggle */
774 mask[4] = 0xF0;
775 match[5] = 0x09; /* start bit = 1, mode2 = 0 */
776 mask[5] = 0x0F;
777
778 rc6_csl = 44;
779 proto = IR_PROTOCOL_RC6;
780 break;
781
782 case RC_PROTO_RC6_6A_24:
783 case RC_PROTO_RC6_6A_32:
784 case RC_PROTO_RC6_MCE:
785 i = 0;
786
787 /* Command */
788 match[i] = wbcir_to_rc6cells(wake_sc >> 0);
789 mask[i++] = wbcir_to_rc6cells(mask_sc >> 0);
790 match[i] = wbcir_to_rc6cells(wake_sc >> 4);
791 mask[i++] = wbcir_to_rc6cells(mask_sc >> 4);
792
793 /* Address + Toggle */
794 match[i] = wbcir_to_rc6cells(wake_sc >> 8);
795 mask[i++] = wbcir_to_rc6cells(mask_sc >> 8);
796 match[i] = wbcir_to_rc6cells(wake_sc >> 12);
797 mask[i++] = wbcir_to_rc6cells(mask_sc >> 12);
798
799 /* Customer bits 7 - 0 */
800 match[i] = wbcir_to_rc6cells(wake_sc >> 16);
801 mask[i++] = wbcir_to_rc6cells(mask_sc >> 16);
802
803 if (rc->wakeup_protocol == RC_PROTO_RC6_6A_20) {
804 rc6_csl = 52;
805 } else {
806 match[i] = wbcir_to_rc6cells(wake_sc >> 20);
807 mask[i++] = wbcir_to_rc6cells(mask_sc >> 20);
808
809 if (rc->wakeup_protocol == RC_PROTO_RC6_6A_24) {
810 rc6_csl = 60;
811 } else {
812 /* Customer range bit and bits 15 - 8 */
813 match[i] = wbcir_to_rc6cells(wake_sc >> 24);
814 mask[i++] = wbcir_to_rc6cells(mask_sc >> 24);
815 match[i] = wbcir_to_rc6cells(wake_sc >> 28);
816 mask[i++] = wbcir_to_rc6cells(mask_sc >> 28);
817 rc6_csl = 76;
818 }
819 }
820
821 /* Header */
822 match[i] = 0x93; /* mode1 = mode0 = 1, submode = 0 */
823 mask[i++] = 0xFF;
824 match[i] = 0x0A; /* start bit = 1, mode2 = 1 */
825 mask[i++] = 0x0F;
826 proto = IR_PROTOCOL_RC6;
827 break;
828 default:
829 do_wake = false;
830 break;
831 }
832
833 finish:
834 if (do_wake) {
835 /* Set compare and compare mask */
836 wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_INDEX,
837 WBCIR_REGSEL_COMPARE | WBCIR_REG_ADDR0,
838 0x3F);
839 outsb(data->wbase + WBCIR_REG_WCEIR_DATA, match, 11);
840 wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_INDEX,
841 WBCIR_REGSEL_MASK | WBCIR_REG_ADDR0,
842 0x3F);
843 outsb(data->wbase + WBCIR_REG_WCEIR_DATA, mask, 11);
844
845 /* RC6 Compare String Len */
846 outb(rc6_csl, data->wbase + WBCIR_REG_WCEIR_CSL);
847
848 /* Clear status bits NEC_REP, BUFF, MSG_END, MATCH */
849 wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_STS, 0x17, 0x17);
850
851 /* Clear BUFF_EN, Clear END_EN, Set MATCH_EN */
852 wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x01, 0x07);
853
854 /* Set CEIR_EN */
855 wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CTL,
856 (proto << 4) | 0x01, 0x31);
857
858 } else {
859 /* Clear BUFF_EN, Clear END_EN, Clear MATCH_EN */
860 wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x00, 0x07);
861
862 /* Clear CEIR_EN */
863 wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CTL, 0x00, 0x01);
864 }
865
866 /*
867 * ACPI will set the HW disable bit for SP3 which means that the
868 * output signals are left in an undefined state which may cause
869 * spurious interrupts which we need to ignore until the hardware
870 * is reinitialized.
871 */
872 wbcir_set_irqmask(data, WBCIR_IRQ_NONE);
873 disable_irq(data->irq);
874 }
875
876 /*
877 * Wakeup handling is done on shutdown.
878 */
879 static int
wbcir_set_wakeup_filter(struct rc_dev * rc,struct rc_scancode_filter * filter)880 wbcir_set_wakeup_filter(struct rc_dev *rc, struct rc_scancode_filter *filter)
881 {
882 return 0;
883 }
884
885 static int
wbcir_suspend(struct pnp_dev * device,pm_message_t state)886 wbcir_suspend(struct pnp_dev *device, pm_message_t state)
887 {
888 struct wbcir_data *data = pnp_get_drvdata(device);
889 led_classdev_suspend(&data->led);
890 wbcir_shutdown(device);
891 return 0;
892 }
893
894 static void
wbcir_init_hw(struct wbcir_data * data)895 wbcir_init_hw(struct wbcir_data *data)
896 {
897 /* Disable interrupts */
898 wbcir_set_irqmask(data, WBCIR_IRQ_NONE);
899
900 /* Set RX_INV, Clear CEIR_EN (needed for the led) */
901 wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CTL, invert ? 8 : 0, 0x09);
902
903 /* Clear status bits NEC_REP, BUFF, MSG_END, MATCH */
904 wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_STS, 0x17, 0x17);
905
906 /* Clear BUFF_EN, Clear END_EN, Clear MATCH_EN */
907 wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x00, 0x07);
908
909 /* Set RC5 cell time to correspond to 36 kHz */
910 wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CFG1, 0x4A, 0x7F);
911
912 /* Set IRTX_INV */
913 if (invert)
914 outb(WBCIR_IRTX_INV, data->ebase + WBCIR_REG_ECEIR_CCTL);
915 else
916 outb(0x00, data->ebase + WBCIR_REG_ECEIR_CCTL);
917
918 /*
919 * Clear IR LED, set SP3 clock to 24Mhz, set TX mask to IRTX1,
920 * set SP3_IRRX_SW to binary 01, helpfully not documented
921 */
922 outb(0x10, data->ebase + WBCIR_REG_ECEIR_CTS);
923 data->txmask = 0x1;
924
925 /* Enable extended mode */
926 wbcir_select_bank(data, WBCIR_BANK_2);
927 outb(WBCIR_EXT_ENABLE, data->sbase + WBCIR_REG_SP3_EXCR1);
928
929 /*
930 * Configure baud generator, IR data will be sampled at
931 * a bitrate of: (24Mhz * prescaler) / (divisor * 16).
932 *
933 * The ECIR registers include a flag to change the
934 * 24Mhz clock freq to 48Mhz.
935 *
936 * It's not documented in the specs, but fifo levels
937 * other than 16 seems to be unsupported.
938 */
939
940 /* prescaler 1.0, tx/rx fifo lvl 16 */
941 outb(0x30, data->sbase + WBCIR_REG_SP3_EXCR2);
942
943 /* Set baud divisor to sample every 10 us */
944 outb(0x0f, data->sbase + WBCIR_REG_SP3_BGDL);
945 outb(0x00, data->sbase + WBCIR_REG_SP3_BGDH);
946
947 /* Set CEIR mode */
948 wbcir_select_bank(data, WBCIR_BANK_0);
949 outb(0xC0, data->sbase + WBCIR_REG_SP3_MCR);
950 inb(data->sbase + WBCIR_REG_SP3_LSR); /* Clear LSR */
951 inb(data->sbase + WBCIR_REG_SP3_MSR); /* Clear MSR */
952
953 /* Disable RX demod, enable run-length enc/dec, set freq span */
954 wbcir_select_bank(data, WBCIR_BANK_7);
955 outb(0x90, data->sbase + WBCIR_REG_SP3_RCCFG);
956
957 /* Disable timer */
958 wbcir_select_bank(data, WBCIR_BANK_4);
959 outb(0x00, data->sbase + WBCIR_REG_SP3_IRCR1);
960
961 /* Disable MSR interrupt, clear AUX_IRX, mask RX during TX? */
962 wbcir_select_bank(data, WBCIR_BANK_5);
963 outb(txandrx ? 0x03 : 0x02, data->sbase + WBCIR_REG_SP3_IRCR2);
964
965 /* Disable CRC */
966 wbcir_select_bank(data, WBCIR_BANK_6);
967 outb(0x20, data->sbase + WBCIR_REG_SP3_IRCR3);
968
969 /* Set RX demodulation freq, not really used */
970 wbcir_select_bank(data, WBCIR_BANK_7);
971 outb(0xF2, data->sbase + WBCIR_REG_SP3_IRRXDC);
972
973 /* Set TX modulation, 36kHz, 7us pulse width */
974 outb(0x69, data->sbase + WBCIR_REG_SP3_IRTXMC);
975 data->txcarrier = 36000;
976
977 /* Set invert and pin direction */
978 if (invert)
979 outb(0x10, data->sbase + WBCIR_REG_SP3_IRCFG4);
980 else
981 outb(0x00, data->sbase + WBCIR_REG_SP3_IRCFG4);
982
983 /* Set FIFO thresholds (RX = 8, TX = 3), reset RX/TX */
984 wbcir_select_bank(data, WBCIR_BANK_0);
985 outb(0x97, data->sbase + WBCIR_REG_SP3_FCR);
986
987 /* Clear AUX status bits */
988 outb(0xE0, data->sbase + WBCIR_REG_SP3_ASCR);
989
990 /* Clear RX state */
991 data->rxstate = WBCIR_RXSTATE_INACTIVE;
992 wbcir_idle_rx(data->dev, true);
993
994 /* Clear TX state */
995 if (data->txstate == WBCIR_TXSTATE_ACTIVE) {
996 kfree(data->txbuf);
997 data->txbuf = NULL;
998 data->txstate = WBCIR_TXSTATE_INACTIVE;
999 }
1000
1001 /* Enable interrupts */
1002 wbcir_set_irqmask(data, WBCIR_IRQ_RX | WBCIR_IRQ_ERR);
1003 }
1004
1005 static int
wbcir_resume(struct pnp_dev * device)1006 wbcir_resume(struct pnp_dev *device)
1007 {
1008 struct wbcir_data *data = pnp_get_drvdata(device);
1009
1010 wbcir_init_hw(data);
1011 ir_raw_event_reset(data->dev);
1012 enable_irq(data->irq);
1013 led_classdev_resume(&data->led);
1014
1015 return 0;
1016 }
1017
1018 static int
wbcir_probe(struct pnp_dev * device,const struct pnp_device_id * dev_id)1019 wbcir_probe(struct pnp_dev *device, const struct pnp_device_id *dev_id)
1020 {
1021 struct device *dev = &device->dev;
1022 struct wbcir_data *data;
1023 int err;
1024
1025 if (!(pnp_port_len(device, 0) == EHFUNC_IOMEM_LEN &&
1026 pnp_port_len(device, 1) == WAKEUP_IOMEM_LEN &&
1027 pnp_port_len(device, 2) == SP_IOMEM_LEN)) {
1028 dev_err(dev, "Invalid resources\n");
1029 return -ENODEV;
1030 }
1031
1032 data = kzalloc(sizeof(*data), GFP_KERNEL);
1033 if (!data) {
1034 err = -ENOMEM;
1035 goto exit;
1036 }
1037
1038 pnp_set_drvdata(device, data);
1039
1040 spin_lock_init(&data->spinlock);
1041 data->ebase = pnp_port_start(device, 0);
1042 data->wbase = pnp_port_start(device, 1);
1043 data->sbase = pnp_port_start(device, 2);
1044 data->irq = pnp_irq(device, 0);
1045
1046 if (data->wbase == 0 || data->ebase == 0 ||
1047 data->sbase == 0 || data->irq == -1) {
1048 err = -ENODEV;
1049 dev_err(dev, "Invalid resources\n");
1050 goto exit_free_data;
1051 }
1052
1053 dev_dbg(&device->dev, "Found device (w: 0x%lX, e: 0x%lX, s: 0x%lX, i: %u)\n",
1054 data->wbase, data->ebase, data->sbase, data->irq);
1055
1056 data->led.name = "cir::activity";
1057 data->led.default_trigger = "rc-feedback";
1058 data->led.brightness_set = wbcir_led_brightness_set;
1059 data->led.brightness_get = wbcir_led_brightness_get;
1060 err = led_classdev_register(&device->dev, &data->led);
1061 if (err)
1062 goto exit_free_data;
1063
1064 data->dev = rc_allocate_device(RC_DRIVER_IR_RAW);
1065 if (!data->dev) {
1066 err = -ENOMEM;
1067 goto exit_unregister_led;
1068 }
1069
1070 data->dev->driver_name = DRVNAME;
1071 data->dev->device_name = WBCIR_NAME;
1072 data->dev->input_phys = "wbcir/cir0";
1073 data->dev->input_id.bustype = BUS_HOST;
1074 data->dev->input_id.vendor = PCI_VENDOR_ID_WINBOND;
1075 data->dev->input_id.product = WBCIR_ID_FAMILY;
1076 data->dev->input_id.version = WBCIR_ID_CHIP;
1077 data->dev->map_name = RC_MAP_RC6_MCE;
1078 data->dev->s_idle = wbcir_idle_rx;
1079 data->dev->s_carrier_report = wbcir_set_carrier_report;
1080 data->dev->s_tx_mask = wbcir_txmask;
1081 data->dev->s_tx_carrier = wbcir_txcarrier;
1082 data->dev->tx_ir = wbcir_tx;
1083 data->dev->priv = data;
1084 data->dev->dev.parent = &device->dev;
1085 data->dev->min_timeout = 1;
1086 data->dev->timeout = IR_DEFAULT_TIMEOUT;
1087 data->dev->max_timeout = 10 * IR_DEFAULT_TIMEOUT;
1088 data->dev->rx_resolution = US_TO_NS(2);
1089 data->dev->allowed_protocols = RC_PROTO_BIT_ALL_IR_DECODER;
1090 data->dev->allowed_wakeup_protocols = RC_PROTO_BIT_NEC |
1091 RC_PROTO_BIT_NECX | RC_PROTO_BIT_NEC32 | RC_PROTO_BIT_RC5 |
1092 RC_PROTO_BIT_RC6_0 | RC_PROTO_BIT_RC6_6A_20 |
1093 RC_PROTO_BIT_RC6_6A_24 | RC_PROTO_BIT_RC6_6A_32 |
1094 RC_PROTO_BIT_RC6_MCE;
1095 data->dev->wakeup_protocol = RC_PROTO_RC6_MCE;
1096 data->dev->scancode_wakeup_filter.data = 0x800f040c;
1097 data->dev->scancode_wakeup_filter.mask = 0xffff7fff;
1098 data->dev->s_wakeup_filter = wbcir_set_wakeup_filter;
1099
1100 err = rc_register_device(data->dev);
1101 if (err)
1102 goto exit_free_rc;
1103
1104 if (!request_region(data->wbase, WAKEUP_IOMEM_LEN, DRVNAME)) {
1105 dev_err(dev, "Region 0x%lx-0x%lx already in use!\n",
1106 data->wbase, data->wbase + WAKEUP_IOMEM_LEN - 1);
1107 err = -EBUSY;
1108 goto exit_unregister_device;
1109 }
1110
1111 if (!request_region(data->ebase, EHFUNC_IOMEM_LEN, DRVNAME)) {
1112 dev_err(dev, "Region 0x%lx-0x%lx already in use!\n",
1113 data->ebase, data->ebase + EHFUNC_IOMEM_LEN - 1);
1114 err = -EBUSY;
1115 goto exit_release_wbase;
1116 }
1117
1118 if (!request_region(data->sbase, SP_IOMEM_LEN, DRVNAME)) {
1119 dev_err(dev, "Region 0x%lx-0x%lx already in use!\n",
1120 data->sbase, data->sbase + SP_IOMEM_LEN - 1);
1121 err = -EBUSY;
1122 goto exit_release_ebase;
1123 }
1124
1125 err = request_irq(data->irq, wbcir_irq_handler,
1126 0, DRVNAME, device);
1127 if (err) {
1128 dev_err(dev, "Failed to claim IRQ %u\n", data->irq);
1129 err = -EBUSY;
1130 goto exit_release_sbase;
1131 }
1132
1133 device_init_wakeup(&device->dev, 1);
1134
1135 wbcir_init_hw(data);
1136
1137 return 0;
1138
1139 exit_release_sbase:
1140 release_region(data->sbase, SP_IOMEM_LEN);
1141 exit_release_ebase:
1142 release_region(data->ebase, EHFUNC_IOMEM_LEN);
1143 exit_release_wbase:
1144 release_region(data->wbase, WAKEUP_IOMEM_LEN);
1145 exit_unregister_device:
1146 rc_unregister_device(data->dev);
1147 data->dev = NULL;
1148 exit_free_rc:
1149 rc_free_device(data->dev);
1150 exit_unregister_led:
1151 led_classdev_unregister(&data->led);
1152 exit_free_data:
1153 kfree(data);
1154 pnp_set_drvdata(device, NULL);
1155 exit:
1156 return err;
1157 }
1158
1159 static void
wbcir_remove(struct pnp_dev * device)1160 wbcir_remove(struct pnp_dev *device)
1161 {
1162 struct wbcir_data *data = pnp_get_drvdata(device);
1163
1164 /* Disable interrupts */
1165 wbcir_set_irqmask(data, WBCIR_IRQ_NONE);
1166 free_irq(data->irq, device);
1167
1168 /* Clear status bits NEC_REP, BUFF, MSG_END, MATCH */
1169 wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_STS, 0x17, 0x17);
1170
1171 /* Clear CEIR_EN */
1172 wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CTL, 0x00, 0x01);
1173
1174 /* Clear BUFF_EN, END_EN, MATCH_EN */
1175 wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x00, 0x07);
1176
1177 rc_unregister_device(data->dev);
1178
1179 led_classdev_unregister(&data->led);
1180
1181 /* This is ok since &data->led isn't actually used */
1182 wbcir_led_brightness_set(&data->led, LED_OFF);
1183
1184 release_region(data->wbase, WAKEUP_IOMEM_LEN);
1185 release_region(data->ebase, EHFUNC_IOMEM_LEN);
1186 release_region(data->sbase, SP_IOMEM_LEN);
1187
1188 kfree(data);
1189
1190 pnp_set_drvdata(device, NULL);
1191 }
1192
1193 static const struct pnp_device_id wbcir_ids[] = {
1194 { "WEC1022", 0 },
1195 { "", 0 }
1196 };
1197 MODULE_DEVICE_TABLE(pnp, wbcir_ids);
1198
1199 static struct pnp_driver wbcir_driver = {
1200 .name = DRVNAME,
1201 .id_table = wbcir_ids,
1202 .probe = wbcir_probe,
1203 .remove = wbcir_remove,
1204 .suspend = wbcir_suspend,
1205 .resume = wbcir_resume,
1206 .shutdown = wbcir_shutdown
1207 };
1208
1209 static int __init
wbcir_init(void)1210 wbcir_init(void)
1211 {
1212 int ret;
1213
1214 ret = pnp_register_driver(&wbcir_driver);
1215 if (ret)
1216 pr_err("Unable to register driver\n");
1217
1218 return ret;
1219 }
1220
1221 static void __exit
wbcir_exit(void)1222 wbcir_exit(void)
1223 {
1224 pnp_unregister_driver(&wbcir_driver);
1225 }
1226
1227 module_init(wbcir_init);
1228 module_exit(wbcir_exit);
1229
1230 MODULE_AUTHOR("David Härdeman <david@hardeman.nu>");
1231 MODULE_DESCRIPTION("Winbond SuperI/O Consumer IR Driver");
1232 MODULE_LICENSE("GPL");
1233