1 /* Low-level parallel-port routines for 8255-based PC-style hardware.
2 *
3 * Authors: Phil Blundell <philb@gnu.org>
4 * Tim Waugh <tim@cyberelk.demon.co.uk>
5 * Jose Renau <renau@acm.org>
6 * David Campbell
7 * Andrea Arcangeli
8 *
9 * based on work by Grant Guenther <grant@torque.net> and Phil Blundell.
10 *
11 * Cleaned up include files - Russell King <linux@arm.uk.linux.org>
12 * DMA support - Bert De Jonghe <bert@sophis.be>
13 * Many ECP bugs fixed. Fred Barnes & Jamie Lokier, 1999
14 * More PCI support now conditional on CONFIG_PCI, 03/2001, Paul G.
15 * Various hacks, Fred Barnes, 04/2001
16 * Updated probing logic - Adam Belay <ambx1@neo.rr.com>
17 */
18
19 /* This driver should work with any hardware that is broadly compatible
20 * with that in the IBM PC. This applies to the majority of integrated
21 * I/O chipsets that are commonly available. The expected register
22 * layout is:
23 *
24 * base+0 data
25 * base+1 status
26 * base+2 control
27 *
28 * In addition, there are some optional registers:
29 *
30 * base+3 EPP address
31 * base+4 EPP data
32 * base+0x400 ECP config A
33 * base+0x401 ECP config B
34 * base+0x402 ECP control
35 *
36 * All registers are 8 bits wide and read/write. If your hardware differs
37 * only in register addresses (eg because your registers are on 32-bit
38 * word boundaries) then you can alter the constants in parport_pc.h to
39 * accommodate this.
40 *
41 * Note that the ECP registers may not start at offset 0x400 for PCI cards,
42 * but rather will start at port->base_hi.
43 */
44
45 #include <linux/module.h>
46 #include <linux/init.h>
47 #include <linux/sched/signal.h>
48 #include <linux/delay.h>
49 #include <linux/errno.h>
50 #include <linux/interrupt.h>
51 #include <linux/ioport.h>
52 #include <linux/kernel.h>
53 #include <linux/slab.h>
54 #include <linux/dma-mapping.h>
55 #include <linux/pci.h>
56 #include <linux/pnp.h>
57 #include <linux/platform_device.h>
58 #include <linux/sysctl.h>
59 #include <linux/io.h>
60 #include <linux/uaccess.h>
61
62 #include <asm/dma.h>
63
64 #include <linux/parport.h>
65 #include <linux/parport_pc.h>
66 #include <linux/via.h>
67 #include <asm/parport.h>
68
69 #define PARPORT_PC_MAX_PORTS PARPORT_MAX
70
71 #ifdef CONFIG_ISA_DMA_API
72 #define HAS_DMA
73 #endif
74
75 /* ECR modes */
76 #define ECR_SPP 00
77 #define ECR_PS2 01
78 #define ECR_PPF 02
79 #define ECR_ECP 03
80 #define ECR_EPP 04
81 #define ECR_VND 05
82 #define ECR_TST 06
83 #define ECR_CNF 07
84 #define ECR_MODE_MASK 0xe0
85 #define ECR_WRITE(p, v) frob_econtrol((p), 0xff, (v))
86
87 #undef DEBUG
88
89 #ifdef DEBUG
90 #define DPRINTK printk
91 #else
92 #define DPRINTK(stuff...)
93 #endif
94
95
96 #define NR_SUPERIOS 3
97 static struct superio_struct { /* For Super-IO chips autodetection */
98 int io;
99 int irq;
100 int dma;
101 } superios[NR_SUPERIOS] = { {0,},};
102
103 static int user_specified;
104 #if defined(CONFIG_PARPORT_PC_SUPERIO) || \
105 (defined(CONFIG_PARPORT_1284) && defined(CONFIG_PARPORT_PC_FIFO))
106 static int verbose_probing;
107 #endif
108 static int pci_registered_parport;
109 static int pnp_registered_parport;
110
111 /* frob_control, but for ECR */
frob_econtrol(struct parport * pb,unsigned char m,unsigned char v)112 static void frob_econtrol(struct parport *pb, unsigned char m,
113 unsigned char v)
114 {
115 unsigned char ectr = 0;
116
117 if (m != 0xff)
118 ectr = inb(ECONTROL(pb));
119
120 DPRINTK(KERN_DEBUG "frob_econtrol(%02x,%02x): %02x -> %02x\n",
121 m, v, ectr, (ectr & ~m) ^ v);
122
123 outb((ectr & ~m) ^ v, ECONTROL(pb));
124 }
125
frob_set_mode(struct parport * p,int mode)126 static inline void frob_set_mode(struct parport *p, int mode)
127 {
128 frob_econtrol(p, ECR_MODE_MASK, mode << 5);
129 }
130
131 #ifdef CONFIG_PARPORT_PC_FIFO
132 /* Safely change the mode bits in the ECR
133 Returns:
134 0 : Success
135 -EBUSY: Could not drain FIFO in some finite amount of time,
136 mode not changed!
137 */
change_mode(struct parport * p,int m)138 static int change_mode(struct parport *p, int m)
139 {
140 const struct parport_pc_private *priv = p->physport->private_data;
141 unsigned char oecr;
142 int mode;
143
144 DPRINTK(KERN_INFO "parport change_mode ECP-ISA to mode 0x%02x\n", m);
145
146 if (!priv->ecr) {
147 printk(KERN_DEBUG "change_mode: but there's no ECR!\n");
148 return 0;
149 }
150
151 /* Bits <7:5> contain the mode. */
152 oecr = inb(ECONTROL(p));
153 mode = (oecr >> 5) & 0x7;
154 if (mode == m)
155 return 0;
156
157 if (mode >= 2 && !(priv->ctr & 0x20)) {
158 /* This mode resets the FIFO, so we may
159 * have to wait for it to drain first. */
160 unsigned long expire = jiffies + p->physport->cad->timeout;
161 int counter;
162 switch (mode) {
163 case ECR_PPF: /* Parallel Port FIFO mode */
164 case ECR_ECP: /* ECP Parallel Port mode */
165 /* Busy wait for 200us */
166 for (counter = 0; counter < 40; counter++) {
167 if (inb(ECONTROL(p)) & 0x01)
168 break;
169 if (signal_pending(current))
170 break;
171 udelay(5);
172 }
173
174 /* Poll slowly. */
175 while (!(inb(ECONTROL(p)) & 0x01)) {
176 if (time_after_eq(jiffies, expire))
177 /* The FIFO is stuck. */
178 return -EBUSY;
179 schedule_timeout_interruptible(
180 msecs_to_jiffies(10));
181 if (signal_pending(current))
182 break;
183 }
184 }
185 }
186
187 if (mode >= 2 && m >= 2) {
188 /* We have to go through mode 001 */
189 oecr &= ~(7 << 5);
190 oecr |= ECR_PS2 << 5;
191 ECR_WRITE(p, oecr);
192 }
193
194 /* Set the mode. */
195 oecr &= ~(7 << 5);
196 oecr |= m << 5;
197 ECR_WRITE(p, oecr);
198 return 0;
199 }
200 #endif /* FIFO support */
201
202 /*
203 * Clear TIMEOUT BIT in EPP MODE
204 *
205 * This is also used in SPP detection.
206 */
clear_epp_timeout(struct parport * pb)207 static int clear_epp_timeout(struct parport *pb)
208 {
209 unsigned char r;
210
211 if (!(parport_pc_read_status(pb) & 0x01))
212 return 1;
213
214 /* To clear timeout some chips require double read */
215 parport_pc_read_status(pb);
216 r = parport_pc_read_status(pb);
217 outb(r | 0x01, STATUS(pb)); /* Some reset by writing 1 */
218 outb(r & 0xfe, STATUS(pb)); /* Others by writing 0 */
219 r = parport_pc_read_status(pb);
220
221 return !(r & 0x01);
222 }
223
224 /*
225 * Access functions.
226 *
227 * Most of these aren't static because they may be used by the
228 * parport_xxx_yyy macros. extern __inline__ versions of several
229 * of these are in parport_pc.h.
230 */
231
parport_pc_init_state(struct pardevice * dev,struct parport_state * s)232 static void parport_pc_init_state(struct pardevice *dev,
233 struct parport_state *s)
234 {
235 s->u.pc.ctr = 0xc;
236 if (dev->irq_func &&
237 dev->port->irq != PARPORT_IRQ_NONE)
238 /* Set ackIntEn */
239 s->u.pc.ctr |= 0x10;
240
241 s->u.pc.ecr = 0x34; /* NetMos chip can cause problems 0x24;
242 * D.Gruszka VScom */
243 }
244
parport_pc_save_state(struct parport * p,struct parport_state * s)245 static void parport_pc_save_state(struct parport *p, struct parport_state *s)
246 {
247 const struct parport_pc_private *priv = p->physport->private_data;
248 s->u.pc.ctr = priv->ctr;
249 if (priv->ecr)
250 s->u.pc.ecr = inb(ECONTROL(p));
251 }
252
parport_pc_restore_state(struct parport * p,struct parport_state * s)253 static void parport_pc_restore_state(struct parport *p,
254 struct parport_state *s)
255 {
256 struct parport_pc_private *priv = p->physport->private_data;
257 register unsigned char c = s->u.pc.ctr & priv->ctr_writable;
258 outb(c, CONTROL(p));
259 priv->ctr = c;
260 if (priv->ecr)
261 ECR_WRITE(p, s->u.pc.ecr);
262 }
263
264 #ifdef CONFIG_PARPORT_1284
parport_pc_epp_read_data(struct parport * port,void * buf,size_t length,int flags)265 static size_t parport_pc_epp_read_data(struct parport *port, void *buf,
266 size_t length, int flags)
267 {
268 size_t got = 0;
269
270 if (flags & PARPORT_W91284PIC) {
271 unsigned char status;
272 size_t left = length;
273
274 /* use knowledge about data lines..:
275 * nFault is 0 if there is at least 1 byte in the Warp's FIFO
276 * pError is 1 if there are 16 bytes in the Warp's FIFO
277 */
278 status = inb(STATUS(port));
279
280 while (!(status & 0x08) && got < length) {
281 if (left >= 16 && (status & 0x20) && !(status & 0x08)) {
282 /* can grab 16 bytes from warp fifo */
283 if (!((long)buf & 0x03))
284 insl(EPPDATA(port), buf, 4);
285 else
286 insb(EPPDATA(port), buf, 16);
287 buf += 16;
288 got += 16;
289 left -= 16;
290 } else {
291 /* grab single byte from the warp fifo */
292 *((char *)buf) = inb(EPPDATA(port));
293 buf++;
294 got++;
295 left--;
296 }
297 status = inb(STATUS(port));
298 if (status & 0x01) {
299 /* EPP timeout should never occur... */
300 printk(KERN_DEBUG
301 "%s: EPP timeout occurred while talking to w91284pic (should not have done)\n", port->name);
302 clear_epp_timeout(port);
303 }
304 }
305 return got;
306 }
307 if ((flags & PARPORT_EPP_FAST) && (length > 1)) {
308 if (!(((long)buf | length) & 0x03))
309 insl(EPPDATA(port), buf, (length >> 2));
310 else
311 insb(EPPDATA(port), buf, length);
312 if (inb(STATUS(port)) & 0x01) {
313 clear_epp_timeout(port);
314 return -EIO;
315 }
316 return length;
317 }
318 for (; got < length; got++) {
319 *((char *)buf) = inb(EPPDATA(port));
320 buf++;
321 if (inb(STATUS(port)) & 0x01) {
322 /* EPP timeout */
323 clear_epp_timeout(port);
324 break;
325 }
326 }
327
328 return got;
329 }
330
parport_pc_epp_write_data(struct parport * port,const void * buf,size_t length,int flags)331 static size_t parport_pc_epp_write_data(struct parport *port, const void *buf,
332 size_t length, int flags)
333 {
334 size_t written = 0;
335
336 if ((flags & PARPORT_EPP_FAST) && (length > 1)) {
337 if (!(((long)buf | length) & 0x03))
338 outsl(EPPDATA(port), buf, (length >> 2));
339 else
340 outsb(EPPDATA(port), buf, length);
341 if (inb(STATUS(port)) & 0x01) {
342 clear_epp_timeout(port);
343 return -EIO;
344 }
345 return length;
346 }
347 for (; written < length; written++) {
348 outb(*((char *)buf), EPPDATA(port));
349 buf++;
350 if (inb(STATUS(port)) & 0x01) {
351 clear_epp_timeout(port);
352 break;
353 }
354 }
355
356 return written;
357 }
358
parport_pc_epp_read_addr(struct parport * port,void * buf,size_t length,int flags)359 static size_t parport_pc_epp_read_addr(struct parport *port, void *buf,
360 size_t length, int flags)
361 {
362 size_t got = 0;
363
364 if ((flags & PARPORT_EPP_FAST) && (length > 1)) {
365 insb(EPPADDR(port), buf, length);
366 if (inb(STATUS(port)) & 0x01) {
367 clear_epp_timeout(port);
368 return -EIO;
369 }
370 return length;
371 }
372 for (; got < length; got++) {
373 *((char *)buf) = inb(EPPADDR(port));
374 buf++;
375 if (inb(STATUS(port)) & 0x01) {
376 clear_epp_timeout(port);
377 break;
378 }
379 }
380
381 return got;
382 }
383
parport_pc_epp_write_addr(struct parport * port,const void * buf,size_t length,int flags)384 static size_t parport_pc_epp_write_addr(struct parport *port,
385 const void *buf, size_t length,
386 int flags)
387 {
388 size_t written = 0;
389
390 if ((flags & PARPORT_EPP_FAST) && (length > 1)) {
391 outsb(EPPADDR(port), buf, length);
392 if (inb(STATUS(port)) & 0x01) {
393 clear_epp_timeout(port);
394 return -EIO;
395 }
396 return length;
397 }
398 for (; written < length; written++) {
399 outb(*((char *)buf), EPPADDR(port));
400 buf++;
401 if (inb(STATUS(port)) & 0x01) {
402 clear_epp_timeout(port);
403 break;
404 }
405 }
406
407 return written;
408 }
409
parport_pc_ecpepp_read_data(struct parport * port,void * buf,size_t length,int flags)410 static size_t parport_pc_ecpepp_read_data(struct parport *port, void *buf,
411 size_t length, int flags)
412 {
413 size_t got;
414
415 frob_set_mode(port, ECR_EPP);
416 parport_pc_data_reverse(port);
417 parport_pc_write_control(port, 0x4);
418 got = parport_pc_epp_read_data(port, buf, length, flags);
419 frob_set_mode(port, ECR_PS2);
420
421 return got;
422 }
423
parport_pc_ecpepp_write_data(struct parport * port,const void * buf,size_t length,int flags)424 static size_t parport_pc_ecpepp_write_data(struct parport *port,
425 const void *buf, size_t length,
426 int flags)
427 {
428 size_t written;
429
430 frob_set_mode(port, ECR_EPP);
431 parport_pc_write_control(port, 0x4);
432 parport_pc_data_forward(port);
433 written = parport_pc_epp_write_data(port, buf, length, flags);
434 frob_set_mode(port, ECR_PS2);
435
436 return written;
437 }
438
parport_pc_ecpepp_read_addr(struct parport * port,void * buf,size_t length,int flags)439 static size_t parport_pc_ecpepp_read_addr(struct parport *port, void *buf,
440 size_t length, int flags)
441 {
442 size_t got;
443
444 frob_set_mode(port, ECR_EPP);
445 parport_pc_data_reverse(port);
446 parport_pc_write_control(port, 0x4);
447 got = parport_pc_epp_read_addr(port, buf, length, flags);
448 frob_set_mode(port, ECR_PS2);
449
450 return got;
451 }
452
parport_pc_ecpepp_write_addr(struct parport * port,const void * buf,size_t length,int flags)453 static size_t parport_pc_ecpepp_write_addr(struct parport *port,
454 const void *buf, size_t length,
455 int flags)
456 {
457 size_t written;
458
459 frob_set_mode(port, ECR_EPP);
460 parport_pc_write_control(port, 0x4);
461 parport_pc_data_forward(port);
462 written = parport_pc_epp_write_addr(port, buf, length, flags);
463 frob_set_mode(port, ECR_PS2);
464
465 return written;
466 }
467 #endif /* IEEE 1284 support */
468
469 #ifdef CONFIG_PARPORT_PC_FIFO
parport_pc_fifo_write_block_pio(struct parport * port,const void * buf,size_t length)470 static size_t parport_pc_fifo_write_block_pio(struct parport *port,
471 const void *buf, size_t length)
472 {
473 int ret = 0;
474 const unsigned char *bufp = buf;
475 size_t left = length;
476 unsigned long expire = jiffies + port->physport->cad->timeout;
477 const unsigned long fifo = FIFO(port);
478 int poll_for = 8; /* 80 usecs */
479 const struct parport_pc_private *priv = port->physport->private_data;
480 const int fifo_depth = priv->fifo_depth;
481
482 port = port->physport;
483
484 /* We don't want to be interrupted every character. */
485 parport_pc_disable_irq(port);
486 /* set nErrIntrEn and serviceIntr */
487 frob_econtrol(port, (1<<4) | (1<<2), (1<<4) | (1<<2));
488
489 /* Forward mode. */
490 parport_pc_data_forward(port); /* Must be in PS2 mode */
491
492 while (left) {
493 unsigned char byte;
494 unsigned char ecrval = inb(ECONTROL(port));
495 int i = 0;
496
497 if (need_resched() && time_before(jiffies, expire))
498 /* Can't yield the port. */
499 schedule();
500
501 /* Anyone else waiting for the port? */
502 if (port->waithead) {
503 printk(KERN_DEBUG "Somebody wants the port\n");
504 break;
505 }
506
507 if (ecrval & 0x02) {
508 /* FIFO is full. Wait for interrupt. */
509
510 /* Clear serviceIntr */
511 ECR_WRITE(port, ecrval & ~(1<<2));
512 false_alarm:
513 ret = parport_wait_event(port, HZ);
514 if (ret < 0)
515 break;
516 ret = 0;
517 if (!time_before(jiffies, expire)) {
518 /* Timed out. */
519 printk(KERN_DEBUG "FIFO write timed out\n");
520 break;
521 }
522 ecrval = inb(ECONTROL(port));
523 if (!(ecrval & (1<<2))) {
524 if (need_resched() &&
525 time_before(jiffies, expire))
526 schedule();
527
528 goto false_alarm;
529 }
530
531 continue;
532 }
533
534 /* Can't fail now. */
535 expire = jiffies + port->cad->timeout;
536
537 poll:
538 if (signal_pending(current))
539 break;
540
541 if (ecrval & 0x01) {
542 /* FIFO is empty. Blast it full. */
543 const int n = left < fifo_depth ? left : fifo_depth;
544 outsb(fifo, bufp, n);
545 bufp += n;
546 left -= n;
547
548 /* Adjust the poll time. */
549 if (i < (poll_for - 2))
550 poll_for--;
551 continue;
552 } else if (i++ < poll_for) {
553 udelay(10);
554 ecrval = inb(ECONTROL(port));
555 goto poll;
556 }
557
558 /* Half-full(call me an optimist) */
559 byte = *bufp++;
560 outb(byte, fifo);
561 left--;
562 }
563 dump_parport_state("leave fifo_write_block_pio", port);
564 return length - left;
565 }
566
567 #ifdef HAS_DMA
parport_pc_fifo_write_block_dma(struct parport * port,const void * buf,size_t length)568 static size_t parport_pc_fifo_write_block_dma(struct parport *port,
569 const void *buf, size_t length)
570 {
571 int ret = 0;
572 unsigned long dmaflag;
573 size_t left = length;
574 const struct parport_pc_private *priv = port->physport->private_data;
575 struct device *dev = port->physport->dev;
576 dma_addr_t dma_addr, dma_handle;
577 size_t maxlen = 0x10000; /* max 64k per DMA transfer */
578 unsigned long start = (unsigned long) buf;
579 unsigned long end = (unsigned long) buf + length - 1;
580
581 dump_parport_state("enter fifo_write_block_dma", port);
582 if (end < MAX_DMA_ADDRESS) {
583 /* If it would cross a 64k boundary, cap it at the end. */
584 if ((start ^ end) & ~0xffffUL)
585 maxlen = 0x10000 - (start & 0xffff);
586
587 dma_addr = dma_handle = dma_map_single(dev, (void *)buf, length,
588 DMA_TO_DEVICE);
589 } else {
590 /* above 16 MB we use a bounce buffer as ISA-DMA
591 is not possible */
592 maxlen = PAGE_SIZE; /* sizeof(priv->dma_buf) */
593 dma_addr = priv->dma_handle;
594 dma_handle = 0;
595 }
596
597 port = port->physport;
598
599 /* We don't want to be interrupted every character. */
600 parport_pc_disable_irq(port);
601 /* set nErrIntrEn and serviceIntr */
602 frob_econtrol(port, (1<<4) | (1<<2), (1<<4) | (1<<2));
603
604 /* Forward mode. */
605 parport_pc_data_forward(port); /* Must be in PS2 mode */
606
607 while (left) {
608 unsigned long expire = jiffies + port->physport->cad->timeout;
609
610 size_t count = left;
611
612 if (count > maxlen)
613 count = maxlen;
614
615 if (!dma_handle) /* bounce buffer ! */
616 memcpy(priv->dma_buf, buf, count);
617
618 dmaflag = claim_dma_lock();
619 disable_dma(port->dma);
620 clear_dma_ff(port->dma);
621 set_dma_mode(port->dma, DMA_MODE_WRITE);
622 set_dma_addr(port->dma, dma_addr);
623 set_dma_count(port->dma, count);
624
625 /* Set DMA mode */
626 frob_econtrol(port, 1<<3, 1<<3);
627
628 /* Clear serviceIntr */
629 frob_econtrol(port, 1<<2, 0);
630
631 enable_dma(port->dma);
632 release_dma_lock(dmaflag);
633
634 /* assume DMA will be successful */
635 left -= count;
636 buf += count;
637 if (dma_handle)
638 dma_addr += count;
639
640 /* Wait for interrupt. */
641 false_alarm:
642 ret = parport_wait_event(port, HZ);
643 if (ret < 0)
644 break;
645 ret = 0;
646 if (!time_before(jiffies, expire)) {
647 /* Timed out. */
648 printk(KERN_DEBUG "DMA write timed out\n");
649 break;
650 }
651 /* Is serviceIntr set? */
652 if (!(inb(ECONTROL(port)) & (1<<2))) {
653 cond_resched();
654
655 goto false_alarm;
656 }
657
658 dmaflag = claim_dma_lock();
659 disable_dma(port->dma);
660 clear_dma_ff(port->dma);
661 count = get_dma_residue(port->dma);
662 release_dma_lock(dmaflag);
663
664 cond_resched(); /* Can't yield the port. */
665
666 /* Anyone else waiting for the port? */
667 if (port->waithead) {
668 printk(KERN_DEBUG "Somebody wants the port\n");
669 break;
670 }
671
672 /* update for possible DMA residue ! */
673 buf -= count;
674 left += count;
675 if (dma_handle)
676 dma_addr -= count;
677 }
678
679 /* Maybe got here through break, so adjust for DMA residue! */
680 dmaflag = claim_dma_lock();
681 disable_dma(port->dma);
682 clear_dma_ff(port->dma);
683 left += get_dma_residue(port->dma);
684 release_dma_lock(dmaflag);
685
686 /* Turn off DMA mode */
687 frob_econtrol(port, 1<<3, 0);
688
689 if (dma_handle)
690 dma_unmap_single(dev, dma_handle, length, DMA_TO_DEVICE);
691
692 dump_parport_state("leave fifo_write_block_dma", port);
693 return length - left;
694 }
695 #endif
696
parport_pc_fifo_write_block(struct parport * port,const void * buf,size_t length)697 static inline size_t parport_pc_fifo_write_block(struct parport *port,
698 const void *buf, size_t length)
699 {
700 #ifdef HAS_DMA
701 if (port->dma != PARPORT_DMA_NONE)
702 return parport_pc_fifo_write_block_dma(port, buf, length);
703 #endif
704 return parport_pc_fifo_write_block_pio(port, buf, length);
705 }
706
707 /* Parallel Port FIFO mode (ECP chipsets) */
parport_pc_compat_write_block_pio(struct parport * port,const void * buf,size_t length,int flags)708 static size_t parport_pc_compat_write_block_pio(struct parport *port,
709 const void *buf, size_t length,
710 int flags)
711 {
712 size_t written;
713 int r;
714 unsigned long expire;
715 const struct parport_pc_private *priv = port->physport->private_data;
716
717 /* Special case: a timeout of zero means we cannot call schedule().
718 * Also if O_NONBLOCK is set then use the default implementation. */
719 if (port->physport->cad->timeout <= PARPORT_INACTIVITY_O_NONBLOCK)
720 return parport_ieee1284_write_compat(port, buf,
721 length, flags);
722
723 /* Set up parallel port FIFO mode.*/
724 parport_pc_data_forward(port); /* Must be in PS2 mode */
725 parport_pc_frob_control(port, PARPORT_CONTROL_STROBE, 0);
726 r = change_mode(port, ECR_PPF); /* Parallel port FIFO */
727 if (r)
728 printk(KERN_DEBUG "%s: Warning change_mode ECR_PPF failed\n",
729 port->name);
730
731 port->physport->ieee1284.phase = IEEE1284_PH_FWD_DATA;
732
733 /* Write the data to the FIFO. */
734 written = parport_pc_fifo_write_block(port, buf, length);
735
736 /* Finish up. */
737 /* For some hardware we don't want to touch the mode until
738 * the FIFO is empty, so allow 4 seconds for each position
739 * in the fifo.
740 */
741 expire = jiffies + (priv->fifo_depth * HZ * 4);
742 do {
743 /* Wait for the FIFO to empty */
744 r = change_mode(port, ECR_PS2);
745 if (r != -EBUSY)
746 break;
747 } while (time_before(jiffies, expire));
748 if (r == -EBUSY) {
749
750 printk(KERN_DEBUG "%s: FIFO is stuck\n", port->name);
751
752 /* Prevent further data transfer. */
753 frob_set_mode(port, ECR_TST);
754
755 /* Adjust for the contents of the FIFO. */
756 for (written -= priv->fifo_depth; ; written++) {
757 if (inb(ECONTROL(port)) & 0x2) {
758 /* Full up. */
759 break;
760 }
761 outb(0, FIFO(port));
762 }
763
764 /* Reset the FIFO and return to PS2 mode. */
765 frob_set_mode(port, ECR_PS2);
766 }
767
768 r = parport_wait_peripheral(port,
769 PARPORT_STATUS_BUSY,
770 PARPORT_STATUS_BUSY);
771 if (r)
772 printk(KERN_DEBUG
773 "%s: BUSY timeout (%d) in compat_write_block_pio\n",
774 port->name, r);
775
776 port->physport->ieee1284.phase = IEEE1284_PH_FWD_IDLE;
777
778 return written;
779 }
780
781 /* ECP */
782 #ifdef CONFIG_PARPORT_1284
parport_pc_ecp_write_block_pio(struct parport * port,const void * buf,size_t length,int flags)783 static size_t parport_pc_ecp_write_block_pio(struct parport *port,
784 const void *buf, size_t length,
785 int flags)
786 {
787 size_t written;
788 int r;
789 unsigned long expire;
790 const struct parport_pc_private *priv = port->physport->private_data;
791
792 /* Special case: a timeout of zero means we cannot call schedule().
793 * Also if O_NONBLOCK is set then use the default implementation. */
794 if (port->physport->cad->timeout <= PARPORT_INACTIVITY_O_NONBLOCK)
795 return parport_ieee1284_ecp_write_data(port, buf,
796 length, flags);
797
798 /* Switch to forward mode if necessary. */
799 if (port->physport->ieee1284.phase != IEEE1284_PH_FWD_IDLE) {
800 /* Event 47: Set nInit high. */
801 parport_frob_control(port,
802 PARPORT_CONTROL_INIT
803 | PARPORT_CONTROL_AUTOFD,
804 PARPORT_CONTROL_INIT
805 | PARPORT_CONTROL_AUTOFD);
806
807 /* Event 49: PError goes high. */
808 r = parport_wait_peripheral(port,
809 PARPORT_STATUS_PAPEROUT,
810 PARPORT_STATUS_PAPEROUT);
811 if (r) {
812 printk(KERN_DEBUG "%s: PError timeout (%d) "
813 "in ecp_write_block_pio\n", port->name, r);
814 }
815 }
816
817 /* Set up ECP parallel port mode.*/
818 parport_pc_data_forward(port); /* Must be in PS2 mode */
819 parport_pc_frob_control(port,
820 PARPORT_CONTROL_STROBE |
821 PARPORT_CONTROL_AUTOFD,
822 0);
823 r = change_mode(port, ECR_ECP); /* ECP FIFO */
824 if (r)
825 printk(KERN_DEBUG "%s: Warning change_mode ECR_ECP failed\n",
826 port->name);
827 port->physport->ieee1284.phase = IEEE1284_PH_FWD_DATA;
828
829 /* Write the data to the FIFO. */
830 written = parport_pc_fifo_write_block(port, buf, length);
831
832 /* Finish up. */
833 /* For some hardware we don't want to touch the mode until
834 * the FIFO is empty, so allow 4 seconds for each position
835 * in the fifo.
836 */
837 expire = jiffies + (priv->fifo_depth * (HZ * 4));
838 do {
839 /* Wait for the FIFO to empty */
840 r = change_mode(port, ECR_PS2);
841 if (r != -EBUSY)
842 break;
843 } while (time_before(jiffies, expire));
844 if (r == -EBUSY) {
845
846 printk(KERN_DEBUG "%s: FIFO is stuck\n", port->name);
847
848 /* Prevent further data transfer. */
849 frob_set_mode(port, ECR_TST);
850
851 /* Adjust for the contents of the FIFO. */
852 for (written -= priv->fifo_depth; ; written++) {
853 if (inb(ECONTROL(port)) & 0x2) {
854 /* Full up. */
855 break;
856 }
857 outb(0, FIFO(port));
858 }
859
860 /* Reset the FIFO and return to PS2 mode. */
861 frob_set_mode(port, ECR_PS2);
862
863 /* Host transfer recovery. */
864 parport_pc_data_reverse(port); /* Must be in PS2 mode */
865 udelay(5);
866 parport_frob_control(port, PARPORT_CONTROL_INIT, 0);
867 r = parport_wait_peripheral(port, PARPORT_STATUS_PAPEROUT, 0);
868 if (r)
869 printk(KERN_DEBUG "%s: PE,1 timeout (%d) "
870 "in ecp_write_block_pio\n", port->name, r);
871
872 parport_frob_control(port,
873 PARPORT_CONTROL_INIT,
874 PARPORT_CONTROL_INIT);
875 r = parport_wait_peripheral(port,
876 PARPORT_STATUS_PAPEROUT,
877 PARPORT_STATUS_PAPEROUT);
878 if (r)
879 printk(KERN_DEBUG "%s: PE,2 timeout (%d) "
880 "in ecp_write_block_pio\n", port->name, r);
881 }
882
883 r = parport_wait_peripheral(port,
884 PARPORT_STATUS_BUSY,
885 PARPORT_STATUS_BUSY);
886 if (r)
887 printk(KERN_DEBUG
888 "%s: BUSY timeout (%d) in ecp_write_block_pio\n",
889 port->name, r);
890
891 port->physport->ieee1284.phase = IEEE1284_PH_FWD_IDLE;
892
893 return written;
894 }
895 #endif /* IEEE 1284 support */
896 #endif /* Allowed to use FIFO/DMA */
897
898
899 /*
900 * ******************************************
901 * INITIALISATION AND MODULE STUFF BELOW HERE
902 * ******************************************
903 */
904
905 /* GCC is not inlining extern inline function later overwritten to non-inline,
906 so we use outlined_ variants here. */
907 static const struct parport_operations parport_pc_ops = {
908 .write_data = parport_pc_write_data,
909 .read_data = parport_pc_read_data,
910
911 .write_control = parport_pc_write_control,
912 .read_control = parport_pc_read_control,
913 .frob_control = parport_pc_frob_control,
914
915 .read_status = parport_pc_read_status,
916
917 .enable_irq = parport_pc_enable_irq,
918 .disable_irq = parport_pc_disable_irq,
919
920 .data_forward = parport_pc_data_forward,
921 .data_reverse = parport_pc_data_reverse,
922
923 .init_state = parport_pc_init_state,
924 .save_state = parport_pc_save_state,
925 .restore_state = parport_pc_restore_state,
926
927 .epp_write_data = parport_ieee1284_epp_write_data,
928 .epp_read_data = parport_ieee1284_epp_read_data,
929 .epp_write_addr = parport_ieee1284_epp_write_addr,
930 .epp_read_addr = parport_ieee1284_epp_read_addr,
931
932 .ecp_write_data = parport_ieee1284_ecp_write_data,
933 .ecp_read_data = parport_ieee1284_ecp_read_data,
934 .ecp_write_addr = parport_ieee1284_ecp_write_addr,
935
936 .compat_write_data = parport_ieee1284_write_compat,
937 .nibble_read_data = parport_ieee1284_read_nibble,
938 .byte_read_data = parport_ieee1284_read_byte,
939
940 .owner = THIS_MODULE,
941 };
942
943 #ifdef CONFIG_PARPORT_PC_SUPERIO
944
find_free_superio(void)945 static struct superio_struct *find_free_superio(void)
946 {
947 int i;
948 for (i = 0; i < NR_SUPERIOS; i++)
949 if (superios[i].io == 0)
950 return &superios[i];
951 return NULL;
952 }
953
954
955 /* Super-IO chipset detection, Winbond, SMSC */
show_parconfig_smsc37c669(int io,int key)956 static void show_parconfig_smsc37c669(int io, int key)
957 {
958 int cr1, cr4, cra, cr23, cr26, cr27;
959 struct superio_struct *s;
960
961 static const char *const modes[] = {
962 "SPP and Bidirectional (PS/2)",
963 "EPP and SPP",
964 "ECP",
965 "ECP and EPP" };
966
967 outb(key, io);
968 outb(key, io);
969 outb(1, io);
970 cr1 = inb(io + 1);
971 outb(4, io);
972 cr4 = inb(io + 1);
973 outb(0x0a, io);
974 cra = inb(io + 1);
975 outb(0x23, io);
976 cr23 = inb(io + 1);
977 outb(0x26, io);
978 cr26 = inb(io + 1);
979 outb(0x27, io);
980 cr27 = inb(io + 1);
981 outb(0xaa, io);
982
983 if (verbose_probing) {
984 printk(KERN_INFO
985 "SMSC 37c669 LPT Config: cr_1=0x%02x, 4=0x%02x, "
986 "A=0x%2x, 23=0x%02x, 26=0x%02x, 27=0x%02x\n",
987 cr1, cr4, cra, cr23, cr26, cr27);
988
989 /* The documentation calls DMA and IRQ-Lines by letters, so
990 the board maker can/will wire them
991 appropriately/randomly... G=reserved H=IDE-irq, */
992 printk(KERN_INFO
993 "SMSC LPT Config: io=0x%04x, irq=%c, dma=%c, fifo threshold=%d\n",
994 cr23 * 4,
995 (cr27 & 0x0f) ? 'A' - 1 + (cr27 & 0x0f) : '-',
996 (cr26 & 0x0f) ? 'A' - 1 + (cr26 & 0x0f) : '-',
997 cra & 0x0f);
998 printk(KERN_INFO "SMSC LPT Config: enabled=%s power=%s\n",
999 (cr23 * 4 >= 0x100) ? "yes" : "no",
1000 (cr1 & 4) ? "yes" : "no");
1001 printk(KERN_INFO
1002 "SMSC LPT Config: Port mode=%s, EPP version =%s\n",
1003 (cr1 & 0x08) ? "Standard mode only (SPP)"
1004 : modes[cr4 & 0x03],
1005 (cr4 & 0x40) ? "1.7" : "1.9");
1006 }
1007
1008 /* Heuristics ! BIOS setup for this mainboard device limits
1009 the choices to standard settings, i.e. io-address and IRQ
1010 are related, however DMA can be 1 or 3, assume DMA_A=DMA1,
1011 DMA_C=DMA3 (this is true e.g. for TYAN 1564D Tomcat IV) */
1012 if (cr23 * 4 >= 0x100) { /* if active */
1013 s = find_free_superio();
1014 if (s == NULL)
1015 printk(KERN_INFO "Super-IO: too many chips!\n");
1016 else {
1017 int d;
1018 switch (cr23 * 4) {
1019 case 0x3bc:
1020 s->io = 0x3bc;
1021 s->irq = 7;
1022 break;
1023 case 0x378:
1024 s->io = 0x378;
1025 s->irq = 7;
1026 break;
1027 case 0x278:
1028 s->io = 0x278;
1029 s->irq = 5;
1030 }
1031 d = (cr26 & 0x0f);
1032 if (d == 1 || d == 3)
1033 s->dma = d;
1034 else
1035 s->dma = PARPORT_DMA_NONE;
1036 }
1037 }
1038 }
1039
1040
show_parconfig_winbond(int io,int key)1041 static void show_parconfig_winbond(int io, int key)
1042 {
1043 int cr30, cr60, cr61, cr70, cr74, crf0;
1044 struct superio_struct *s;
1045 static const char *const modes[] = {
1046 "Standard (SPP) and Bidirectional(PS/2)", /* 0 */
1047 "EPP-1.9 and SPP",
1048 "ECP",
1049 "ECP and EPP-1.9",
1050 "Standard (SPP)",
1051 "EPP-1.7 and SPP", /* 5 */
1052 "undefined!",
1053 "ECP and EPP-1.7" };
1054 static char *const irqtypes[] = {
1055 "pulsed low, high-Z",
1056 "follows nACK" };
1057
1058 /* The registers are called compatible-PnP because the
1059 register layout is modelled after ISA-PnP, the access
1060 method is just another ... */
1061 outb(key, io);
1062 outb(key, io);
1063 outb(0x07, io); /* Register 7: Select Logical Device */
1064 outb(0x01, io + 1); /* LD1 is Parallel Port */
1065 outb(0x30, io);
1066 cr30 = inb(io + 1);
1067 outb(0x60, io);
1068 cr60 = inb(io + 1);
1069 outb(0x61, io);
1070 cr61 = inb(io + 1);
1071 outb(0x70, io);
1072 cr70 = inb(io + 1);
1073 outb(0x74, io);
1074 cr74 = inb(io + 1);
1075 outb(0xf0, io);
1076 crf0 = inb(io + 1);
1077 outb(0xaa, io);
1078
1079 if (verbose_probing) {
1080 printk(KERN_INFO
1081 "Winbond LPT Config: cr_30=%02x 60,61=%02x%02x 70=%02x 74=%02x, f0=%02x\n",
1082 cr30, cr60, cr61, cr70, cr74, crf0);
1083 printk(KERN_INFO "Winbond LPT Config: active=%s, io=0x%02x%02x irq=%d, ",
1084 (cr30 & 0x01) ? "yes" : "no", cr60, cr61, cr70 & 0x0f);
1085 if ((cr74 & 0x07) > 3)
1086 pr_cont("dma=none\n");
1087 else
1088 pr_cont("dma=%d\n", cr74 & 0x07);
1089 printk(KERN_INFO
1090 "Winbond LPT Config: irqtype=%s, ECP fifo threshold=%d\n",
1091 irqtypes[crf0>>7], (crf0>>3)&0x0f);
1092 printk(KERN_INFO "Winbond LPT Config: Port mode=%s\n",
1093 modes[crf0 & 0x07]);
1094 }
1095
1096 if (cr30 & 0x01) { /* the settings can be interrogated later ... */
1097 s = find_free_superio();
1098 if (s == NULL)
1099 printk(KERN_INFO "Super-IO: too many chips!\n");
1100 else {
1101 s->io = (cr60 << 8) | cr61;
1102 s->irq = cr70 & 0x0f;
1103 s->dma = (((cr74 & 0x07) > 3) ?
1104 PARPORT_DMA_NONE : (cr74 & 0x07));
1105 }
1106 }
1107 }
1108
decode_winbond(int efer,int key,int devid,int devrev,int oldid)1109 static void decode_winbond(int efer, int key, int devid, int devrev, int oldid)
1110 {
1111 const char *type = "unknown";
1112 int id, progif = 2;
1113
1114 if (devid == devrev)
1115 /* simple heuristics, we happened to read some
1116 non-winbond register */
1117 return;
1118
1119 id = (devid << 8) | devrev;
1120
1121 /* Values are from public data sheets pdf files, I can just
1122 confirm 83977TF is correct :-) */
1123 if (id == 0x9771)
1124 type = "83977F/AF";
1125 else if (id == 0x9773)
1126 type = "83977TF / SMSC 97w33x/97w34x";
1127 else if (id == 0x9774)
1128 type = "83977ATF";
1129 else if ((id & ~0x0f) == 0x5270)
1130 type = "83977CTF / SMSC 97w36x";
1131 else if ((id & ~0x0f) == 0x52f0)
1132 type = "83977EF / SMSC 97w35x";
1133 else if ((id & ~0x0f) == 0x5210)
1134 type = "83627";
1135 else if ((id & ~0x0f) == 0x6010)
1136 type = "83697HF";
1137 else if ((oldid & 0x0f) == 0x0a) {
1138 type = "83877F";
1139 progif = 1;
1140 } else if ((oldid & 0x0f) == 0x0b) {
1141 type = "83877AF";
1142 progif = 1;
1143 } else if ((oldid & 0x0f) == 0x0c) {
1144 type = "83877TF";
1145 progif = 1;
1146 } else if ((oldid & 0x0f) == 0x0d) {
1147 type = "83877ATF";
1148 progif = 1;
1149 } else
1150 progif = 0;
1151
1152 if (verbose_probing)
1153 printk(KERN_INFO "Winbond chip at EFER=0x%x key=0x%02x "
1154 "devid=%02x devrev=%02x oldid=%02x type=%s\n",
1155 efer, key, devid, devrev, oldid, type);
1156
1157 if (progif == 2)
1158 show_parconfig_winbond(efer, key);
1159 }
1160
decode_smsc(int efer,int key,int devid,int devrev)1161 static void decode_smsc(int efer, int key, int devid, int devrev)
1162 {
1163 const char *type = "unknown";
1164 void (*func)(int io, int key);
1165 int id;
1166
1167 if (devid == devrev)
1168 /* simple heuristics, we happened to read some
1169 non-smsc register */
1170 return;
1171
1172 func = NULL;
1173 id = (devid << 8) | devrev;
1174
1175 if (id == 0x0302) {
1176 type = "37c669";
1177 func = show_parconfig_smsc37c669;
1178 } else if (id == 0x6582)
1179 type = "37c665IR";
1180 else if (devid == 0x65)
1181 type = "37c665GT";
1182 else if (devid == 0x66)
1183 type = "37c666GT";
1184
1185 if (verbose_probing)
1186 printk(KERN_INFO "SMSC chip at EFER=0x%x "
1187 "key=0x%02x devid=%02x devrev=%02x type=%s\n",
1188 efer, key, devid, devrev, type);
1189
1190 if (func)
1191 func(efer, key);
1192 }
1193
1194
winbond_check(int io,int key)1195 static void winbond_check(int io, int key)
1196 {
1197 int origval, devid, devrev, oldid, x_devid, x_devrev, x_oldid;
1198
1199 if (!request_region(io, 3, __func__))
1200 return;
1201
1202 origval = inb(io); /* Save original value */
1203
1204 /* First probe without key */
1205 outb(0x20, io);
1206 x_devid = inb(io + 1);
1207 outb(0x21, io);
1208 x_devrev = inb(io + 1);
1209 outb(0x09, io);
1210 x_oldid = inb(io + 1);
1211
1212 outb(key, io);
1213 outb(key, io); /* Write Magic Sequence to EFER, extended
1214 function enable register */
1215 outb(0x20, io); /* Write EFIR, extended function index register */
1216 devid = inb(io + 1); /* Read EFDR, extended function data register */
1217 outb(0x21, io);
1218 devrev = inb(io + 1);
1219 outb(0x09, io);
1220 oldid = inb(io + 1);
1221 outb(0xaa, io); /* Magic Seal */
1222
1223 outb(origval, io); /* in case we poked some entirely different hardware */
1224
1225 if ((x_devid == devid) && (x_devrev == devrev) && (x_oldid == oldid))
1226 goto out; /* protection against false positives */
1227
1228 decode_winbond(io, key, devid, devrev, oldid);
1229 out:
1230 release_region(io, 3);
1231 }
1232
winbond_check2(int io,int key)1233 static void winbond_check2(int io, int key)
1234 {
1235 int origval[3], devid, devrev, oldid, x_devid, x_devrev, x_oldid;
1236
1237 if (!request_region(io, 3, __func__))
1238 return;
1239
1240 origval[0] = inb(io); /* Save original values */
1241 origval[1] = inb(io + 1);
1242 origval[2] = inb(io + 2);
1243
1244 /* First probe without the key */
1245 outb(0x20, io + 2);
1246 x_devid = inb(io + 2);
1247 outb(0x21, io + 1);
1248 x_devrev = inb(io + 2);
1249 outb(0x09, io + 1);
1250 x_oldid = inb(io + 2);
1251
1252 outb(key, io); /* Write Magic Byte to EFER, extended
1253 function enable register */
1254 outb(0x20, io + 2); /* Write EFIR, extended function index register */
1255 devid = inb(io + 2); /* Read EFDR, extended function data register */
1256 outb(0x21, io + 1);
1257 devrev = inb(io + 2);
1258 outb(0x09, io + 1);
1259 oldid = inb(io + 2);
1260 outb(0xaa, io); /* Magic Seal */
1261
1262 outb(origval[0], io); /* in case we poked some entirely different hardware */
1263 outb(origval[1], io + 1);
1264 outb(origval[2], io + 2);
1265
1266 if (x_devid == devid && x_devrev == devrev && x_oldid == oldid)
1267 goto out; /* protection against false positives */
1268
1269 decode_winbond(io, key, devid, devrev, oldid);
1270 out:
1271 release_region(io, 3);
1272 }
1273
smsc_check(int io,int key)1274 static void smsc_check(int io, int key)
1275 {
1276 int origval, id, rev, oldid, oldrev, x_id, x_rev, x_oldid, x_oldrev;
1277
1278 if (!request_region(io, 3, __func__))
1279 return;
1280
1281 origval = inb(io); /* Save original value */
1282
1283 /* First probe without the key */
1284 outb(0x0d, io);
1285 x_oldid = inb(io + 1);
1286 outb(0x0e, io);
1287 x_oldrev = inb(io + 1);
1288 outb(0x20, io);
1289 x_id = inb(io + 1);
1290 outb(0x21, io);
1291 x_rev = inb(io + 1);
1292
1293 outb(key, io);
1294 outb(key, io); /* Write Magic Sequence to EFER, extended
1295 function enable register */
1296 outb(0x0d, io); /* Write EFIR, extended function index register */
1297 oldid = inb(io + 1); /* Read EFDR, extended function data register */
1298 outb(0x0e, io);
1299 oldrev = inb(io + 1);
1300 outb(0x20, io);
1301 id = inb(io + 1);
1302 outb(0x21, io);
1303 rev = inb(io + 1);
1304 outb(0xaa, io); /* Magic Seal */
1305
1306 outb(origval, io); /* in case we poked some entirely different hardware */
1307
1308 if (x_id == id && x_oldrev == oldrev &&
1309 x_oldid == oldid && x_rev == rev)
1310 goto out; /* protection against false positives */
1311
1312 decode_smsc(io, key, oldid, oldrev);
1313 out:
1314 release_region(io, 3);
1315 }
1316
1317
detect_and_report_winbond(void)1318 static void detect_and_report_winbond(void)
1319 {
1320 if (verbose_probing)
1321 printk(KERN_DEBUG "Winbond Super-IO detection, now testing ports 3F0,370,250,4E,2E ...\n");
1322 winbond_check(0x3f0, 0x87);
1323 winbond_check(0x370, 0x87);
1324 winbond_check(0x2e , 0x87);
1325 winbond_check(0x4e , 0x87);
1326 winbond_check(0x3f0, 0x86);
1327 winbond_check2(0x250, 0x88);
1328 winbond_check2(0x250, 0x89);
1329 }
1330
detect_and_report_smsc(void)1331 static void detect_and_report_smsc(void)
1332 {
1333 if (verbose_probing)
1334 printk(KERN_DEBUG "SMSC Super-IO detection, now testing Ports 2F0, 370 ...\n");
1335 smsc_check(0x3f0, 0x55);
1336 smsc_check(0x370, 0x55);
1337 smsc_check(0x3f0, 0x44);
1338 smsc_check(0x370, 0x44);
1339 }
1340
detect_and_report_it87(void)1341 static void detect_and_report_it87(void)
1342 {
1343 u16 dev;
1344 u8 origval, r;
1345 if (verbose_probing)
1346 printk(KERN_DEBUG "IT8705 Super-IO detection, now testing port 2E ...\n");
1347 if (!request_muxed_region(0x2e, 2, __func__))
1348 return;
1349 origval = inb(0x2e); /* Save original value */
1350 outb(0x87, 0x2e);
1351 outb(0x01, 0x2e);
1352 outb(0x55, 0x2e);
1353 outb(0x55, 0x2e);
1354 outb(0x20, 0x2e);
1355 dev = inb(0x2f) << 8;
1356 outb(0x21, 0x2e);
1357 dev |= inb(0x2f);
1358 if (dev == 0x8712 || dev == 0x8705 || dev == 0x8715 ||
1359 dev == 0x8716 || dev == 0x8718 || dev == 0x8726) {
1360 printk(KERN_INFO "IT%04X SuperIO detected.\n", dev);
1361 outb(0x07, 0x2E); /* Parallel Port */
1362 outb(0x03, 0x2F);
1363 outb(0xF0, 0x2E); /* BOOT 0x80 off */
1364 r = inb(0x2f);
1365 outb(0xF0, 0x2E);
1366 outb(r | 8, 0x2F);
1367 outb(0x02, 0x2E); /* Lock */
1368 outb(0x02, 0x2F);
1369 } else {
1370 outb(origval, 0x2e); /* Oops, sorry to disturb */
1371 }
1372 release_region(0x2e, 2);
1373 }
1374 #endif /* CONFIG_PARPORT_PC_SUPERIO */
1375
find_superio(struct parport * p)1376 static struct superio_struct *find_superio(struct parport *p)
1377 {
1378 int i;
1379 for (i = 0; i < NR_SUPERIOS; i++)
1380 if (superios[i].io == p->base)
1381 return &superios[i];
1382 return NULL;
1383 }
1384
get_superio_dma(struct parport * p)1385 static int get_superio_dma(struct parport *p)
1386 {
1387 struct superio_struct *s = find_superio(p);
1388 if (s)
1389 return s->dma;
1390 return PARPORT_DMA_NONE;
1391 }
1392
get_superio_irq(struct parport * p)1393 static int get_superio_irq(struct parport *p)
1394 {
1395 struct superio_struct *s = find_superio(p);
1396 if (s)
1397 return s->irq;
1398 return PARPORT_IRQ_NONE;
1399 }
1400
1401
1402 /* --- Mode detection ------------------------------------- */
1403
1404 /*
1405 * Checks for port existence, all ports support SPP MODE
1406 * Returns:
1407 * 0 : No parallel port at this address
1408 * PARPORT_MODE_PCSPP : SPP port detected
1409 * (if the user specified an ioport himself,
1410 * this shall always be the case!)
1411 *
1412 */
parport_SPP_supported(struct parport * pb)1413 static int parport_SPP_supported(struct parport *pb)
1414 {
1415 unsigned char r, w;
1416
1417 /*
1418 * first clear an eventually pending EPP timeout
1419 * I (sailer@ife.ee.ethz.ch) have an SMSC chipset
1420 * that does not even respond to SPP cycles if an EPP
1421 * timeout is pending
1422 */
1423 clear_epp_timeout(pb);
1424
1425 /* Do a simple read-write test to make sure the port exists. */
1426 w = 0xc;
1427 outb(w, CONTROL(pb));
1428
1429 /* Is there a control register that we can read from? Some
1430 * ports don't allow reads, so read_control just returns a
1431 * software copy. Some ports _do_ allow reads, so bypass the
1432 * software copy here. In addition, some bits aren't
1433 * writable. */
1434 r = inb(CONTROL(pb));
1435 if ((r & 0xf) == w) {
1436 w = 0xe;
1437 outb(w, CONTROL(pb));
1438 r = inb(CONTROL(pb));
1439 outb(0xc, CONTROL(pb));
1440 if ((r & 0xf) == w)
1441 return PARPORT_MODE_PCSPP;
1442 }
1443
1444 if (user_specified)
1445 /* That didn't work, but the user thinks there's a
1446 * port here. */
1447 printk(KERN_INFO "parport 0x%lx (WARNING): CTR: "
1448 "wrote 0x%02x, read 0x%02x\n", pb->base, w, r);
1449
1450 /* Try the data register. The data lines aren't tri-stated at
1451 * this stage, so we expect back what we wrote. */
1452 w = 0xaa;
1453 parport_pc_write_data(pb, w);
1454 r = parport_pc_read_data(pb);
1455 if (r == w) {
1456 w = 0x55;
1457 parport_pc_write_data(pb, w);
1458 r = parport_pc_read_data(pb);
1459 if (r == w)
1460 return PARPORT_MODE_PCSPP;
1461 }
1462
1463 if (user_specified) {
1464 /* Didn't work, but the user is convinced this is the
1465 * place. */
1466 printk(KERN_INFO "parport 0x%lx (WARNING): DATA: "
1467 "wrote 0x%02x, read 0x%02x\n", pb->base, w, r);
1468 printk(KERN_INFO "parport 0x%lx: You gave this address, "
1469 "but there is probably no parallel port there!\n",
1470 pb->base);
1471 }
1472
1473 /* It's possible that we can't read the control register or
1474 * the data register. In that case just believe the user. */
1475 if (user_specified)
1476 return PARPORT_MODE_PCSPP;
1477
1478 return 0;
1479 }
1480
1481 /* Check for ECR
1482 *
1483 * Old style XT ports alias io ports every 0x400, hence accessing ECR
1484 * on these cards actually accesses the CTR.
1485 *
1486 * Modern cards don't do this but reading from ECR will return 0xff
1487 * regardless of what is written here if the card does NOT support
1488 * ECP.
1489 *
1490 * We first check to see if ECR is the same as CTR. If not, the low
1491 * two bits of ECR aren't writable, so we check by writing ECR and
1492 * reading it back to see if it's what we expect.
1493 */
parport_ECR_present(struct parport * pb)1494 static int parport_ECR_present(struct parport *pb)
1495 {
1496 struct parport_pc_private *priv = pb->private_data;
1497 unsigned char r = 0xc;
1498
1499 outb(r, CONTROL(pb));
1500 if ((inb(ECONTROL(pb)) & 0x3) == (r & 0x3)) {
1501 outb(r ^ 0x2, CONTROL(pb)); /* Toggle bit 1 */
1502
1503 r = inb(CONTROL(pb));
1504 if ((inb(ECONTROL(pb)) & 0x2) == (r & 0x2))
1505 goto no_reg; /* Sure that no ECR register exists */
1506 }
1507
1508 if ((inb(ECONTROL(pb)) & 0x3) != 0x1)
1509 goto no_reg;
1510
1511 ECR_WRITE(pb, 0x34);
1512 if (inb(ECONTROL(pb)) != 0x35)
1513 goto no_reg;
1514
1515 priv->ecr = 1;
1516 outb(0xc, CONTROL(pb));
1517
1518 /* Go to mode 000 */
1519 frob_set_mode(pb, ECR_SPP);
1520
1521 return 1;
1522
1523 no_reg:
1524 outb(0xc, CONTROL(pb));
1525 return 0;
1526 }
1527
1528 #ifdef CONFIG_PARPORT_1284
1529 /* Detect PS/2 support.
1530 *
1531 * Bit 5 (0x20) sets the PS/2 data direction; setting this high
1532 * allows us to read data from the data lines. In theory we would get back
1533 * 0xff but any peripheral attached to the port may drag some or all of the
1534 * lines down to zero. So if we get back anything that isn't the contents
1535 * of the data register we deem PS/2 support to be present.
1536 *
1537 * Some SPP ports have "half PS/2" ability - you can't turn off the line
1538 * drivers, but an external peripheral with sufficiently beefy drivers of
1539 * its own can overpower them and assert its own levels onto the bus, from
1540 * where they can then be read back as normal. Ports with this property
1541 * and the right type of device attached are likely to fail the SPP test,
1542 * (as they will appear to have stuck bits) and so the fact that they might
1543 * be misdetected here is rather academic.
1544 */
1545
parport_PS2_supported(struct parport * pb)1546 static int parport_PS2_supported(struct parport *pb)
1547 {
1548 int ok = 0;
1549
1550 clear_epp_timeout(pb);
1551
1552 /* try to tri-state the buffer */
1553 parport_pc_data_reverse(pb);
1554
1555 parport_pc_write_data(pb, 0x55);
1556 if (parport_pc_read_data(pb) != 0x55)
1557 ok++;
1558
1559 parport_pc_write_data(pb, 0xaa);
1560 if (parport_pc_read_data(pb) != 0xaa)
1561 ok++;
1562
1563 /* cancel input mode */
1564 parport_pc_data_forward(pb);
1565
1566 if (ok) {
1567 pb->modes |= PARPORT_MODE_TRISTATE;
1568 } else {
1569 struct parport_pc_private *priv = pb->private_data;
1570 priv->ctr_writable &= ~0x20;
1571 }
1572
1573 return ok;
1574 }
1575
1576 #ifdef CONFIG_PARPORT_PC_FIFO
parport_ECP_supported(struct parport * pb)1577 static int parport_ECP_supported(struct parport *pb)
1578 {
1579 int i;
1580 int config, configb;
1581 int pword;
1582 struct parport_pc_private *priv = pb->private_data;
1583 /* Translate ECP intrLine to ISA irq value */
1584 static const int intrline[] = { 0, 7, 9, 10, 11, 14, 15, 5 };
1585
1586 /* If there is no ECR, we have no hope of supporting ECP. */
1587 if (!priv->ecr)
1588 return 0;
1589
1590 /* Find out FIFO depth */
1591 ECR_WRITE(pb, ECR_SPP << 5); /* Reset FIFO */
1592 ECR_WRITE(pb, ECR_TST << 5); /* TEST FIFO */
1593 for (i = 0; i < 1024 && !(inb(ECONTROL(pb)) & 0x02); i++)
1594 outb(0xaa, FIFO(pb));
1595
1596 /*
1597 * Using LGS chipset it uses ECR register, but
1598 * it doesn't support ECP or FIFO MODE
1599 */
1600 if (i == 1024) {
1601 ECR_WRITE(pb, ECR_SPP << 5);
1602 return 0;
1603 }
1604
1605 priv->fifo_depth = i;
1606 if (verbose_probing)
1607 printk(KERN_DEBUG "0x%lx: FIFO is %d bytes\n", pb->base, i);
1608
1609 /* Find out writeIntrThreshold */
1610 frob_econtrol(pb, 1<<2, 1<<2);
1611 frob_econtrol(pb, 1<<2, 0);
1612 for (i = 1; i <= priv->fifo_depth; i++) {
1613 inb(FIFO(pb));
1614 udelay(50);
1615 if (inb(ECONTROL(pb)) & (1<<2))
1616 break;
1617 }
1618
1619 if (i <= priv->fifo_depth) {
1620 if (verbose_probing)
1621 printk(KERN_DEBUG "0x%lx: writeIntrThreshold is %d\n",
1622 pb->base, i);
1623 } else
1624 /* Number of bytes we know we can write if we get an
1625 interrupt. */
1626 i = 0;
1627
1628 priv->writeIntrThreshold = i;
1629
1630 /* Find out readIntrThreshold */
1631 frob_set_mode(pb, ECR_PS2); /* Reset FIFO and enable PS2 */
1632 parport_pc_data_reverse(pb); /* Must be in PS2 mode */
1633 frob_set_mode(pb, ECR_TST); /* Test FIFO */
1634 frob_econtrol(pb, 1<<2, 1<<2);
1635 frob_econtrol(pb, 1<<2, 0);
1636 for (i = 1; i <= priv->fifo_depth; i++) {
1637 outb(0xaa, FIFO(pb));
1638 if (inb(ECONTROL(pb)) & (1<<2))
1639 break;
1640 }
1641
1642 if (i <= priv->fifo_depth) {
1643 if (verbose_probing)
1644 printk(KERN_INFO "0x%lx: readIntrThreshold is %d\n",
1645 pb->base, i);
1646 } else
1647 /* Number of bytes we can read if we get an interrupt. */
1648 i = 0;
1649
1650 priv->readIntrThreshold = i;
1651
1652 ECR_WRITE(pb, ECR_SPP << 5); /* Reset FIFO */
1653 ECR_WRITE(pb, 0xf4); /* Configuration mode */
1654 config = inb(CONFIGA(pb));
1655 pword = (config >> 4) & 0x7;
1656 switch (pword) {
1657 case 0:
1658 pword = 2;
1659 printk(KERN_WARNING "0x%lx: Unsupported pword size!\n",
1660 pb->base);
1661 break;
1662 case 2:
1663 pword = 4;
1664 printk(KERN_WARNING "0x%lx: Unsupported pword size!\n",
1665 pb->base);
1666 break;
1667 default:
1668 printk(KERN_WARNING "0x%lx: Unknown implementation ID\n",
1669 pb->base);
1670 /* Assume 1 */
1671 case 1:
1672 pword = 1;
1673 }
1674 priv->pword = pword;
1675
1676 if (verbose_probing) {
1677 printk(KERN_DEBUG "0x%lx: PWord is %d bits\n",
1678 pb->base, 8 * pword);
1679
1680 printk(KERN_DEBUG "0x%lx: Interrupts are ISA-%s\n", pb->base,
1681 config & 0x80 ? "Level" : "Pulses");
1682
1683 configb = inb(CONFIGB(pb));
1684 printk(KERN_DEBUG "0x%lx: ECP port cfgA=0x%02x cfgB=0x%02x\n",
1685 pb->base, config, configb);
1686 printk(KERN_DEBUG "0x%lx: ECP settings irq=", pb->base);
1687 if ((configb >> 3) & 0x07)
1688 pr_cont("%d", intrline[(configb >> 3) & 0x07]);
1689 else
1690 pr_cont("<none or set by other means>");
1691 pr_cont(" dma=");
1692 if ((configb & 0x03) == 0x00)
1693 pr_cont("<none or set by other means>\n");
1694 else
1695 pr_cont("%d\n", configb & 0x07);
1696 }
1697
1698 /* Go back to mode 000 */
1699 frob_set_mode(pb, ECR_SPP);
1700
1701 return 1;
1702 }
1703 #endif
1704
1705 #ifdef CONFIG_X86_32
intel_bug_present_check_epp(struct parport * pb)1706 static int intel_bug_present_check_epp(struct parport *pb)
1707 {
1708 const struct parport_pc_private *priv = pb->private_data;
1709 int bug_present = 0;
1710
1711 if (priv->ecr) {
1712 /* store value of ECR */
1713 unsigned char ecr = inb(ECONTROL(pb));
1714 unsigned char i;
1715 for (i = 0x00; i < 0x80; i += 0x20) {
1716 ECR_WRITE(pb, i);
1717 if (clear_epp_timeout(pb)) {
1718 /* Phony EPP in ECP. */
1719 bug_present = 1;
1720 break;
1721 }
1722 }
1723 /* return ECR into the inital state */
1724 ECR_WRITE(pb, ecr);
1725 }
1726
1727 return bug_present;
1728 }
intel_bug_present(struct parport * pb)1729 static int intel_bug_present(struct parport *pb)
1730 {
1731 /* Check whether the device is legacy, not PCI or PCMCIA. Only legacy is known to be affected. */
1732 if (pb->dev != NULL) {
1733 return 0;
1734 }
1735
1736 return intel_bug_present_check_epp(pb);
1737 }
1738 #else
intel_bug_present(struct parport * pb)1739 static int intel_bug_present(struct parport *pb)
1740 {
1741 return 0;
1742 }
1743 #endif /* CONFIG_X86_32 */
1744
parport_ECPPS2_supported(struct parport * pb)1745 static int parport_ECPPS2_supported(struct parport *pb)
1746 {
1747 const struct parport_pc_private *priv = pb->private_data;
1748 int result;
1749 unsigned char oecr;
1750
1751 if (!priv->ecr)
1752 return 0;
1753
1754 oecr = inb(ECONTROL(pb));
1755 ECR_WRITE(pb, ECR_PS2 << 5);
1756 result = parport_PS2_supported(pb);
1757 ECR_WRITE(pb, oecr);
1758 return result;
1759 }
1760
1761 /* EPP mode detection */
1762
parport_EPP_supported(struct parport * pb)1763 static int parport_EPP_supported(struct parport *pb)
1764 {
1765 /*
1766 * Theory:
1767 * Bit 0 of STR is the EPP timeout bit, this bit is 0
1768 * when EPP is possible and is set high when an EPP timeout
1769 * occurs (EPP uses the HALT line to stop the CPU while it does
1770 * the byte transfer, an EPP timeout occurs if the attached
1771 * device fails to respond after 10 micro seconds).
1772 *
1773 * This bit is cleared by either reading it (National Semi)
1774 * or writing a 1 to the bit (SMC, UMC, WinBond), others ???
1775 * This bit is always high in non EPP modes.
1776 */
1777
1778 /* If EPP timeout bit clear then EPP available */
1779 if (!clear_epp_timeout(pb))
1780 return 0; /* No way to clear timeout */
1781
1782 /* Check for Intel bug. */
1783 if (intel_bug_present(pb))
1784 return 0;
1785
1786 pb->modes |= PARPORT_MODE_EPP;
1787
1788 /* Set up access functions to use EPP hardware. */
1789 pb->ops->epp_read_data = parport_pc_epp_read_data;
1790 pb->ops->epp_write_data = parport_pc_epp_write_data;
1791 pb->ops->epp_read_addr = parport_pc_epp_read_addr;
1792 pb->ops->epp_write_addr = parport_pc_epp_write_addr;
1793
1794 return 1;
1795 }
1796
parport_ECPEPP_supported(struct parport * pb)1797 static int parport_ECPEPP_supported(struct parport *pb)
1798 {
1799 struct parport_pc_private *priv = pb->private_data;
1800 int result;
1801 unsigned char oecr;
1802
1803 if (!priv->ecr)
1804 return 0;
1805
1806 oecr = inb(ECONTROL(pb));
1807 /* Search for SMC style EPP+ECP mode */
1808 ECR_WRITE(pb, 0x80);
1809 outb(0x04, CONTROL(pb));
1810 result = parport_EPP_supported(pb);
1811
1812 ECR_WRITE(pb, oecr);
1813
1814 if (result) {
1815 /* Set up access functions to use ECP+EPP hardware. */
1816 pb->ops->epp_read_data = parport_pc_ecpepp_read_data;
1817 pb->ops->epp_write_data = parport_pc_ecpepp_write_data;
1818 pb->ops->epp_read_addr = parport_pc_ecpepp_read_addr;
1819 pb->ops->epp_write_addr = parport_pc_ecpepp_write_addr;
1820 }
1821
1822 return result;
1823 }
1824
1825 #else /* No IEEE 1284 support */
1826
1827 /* Don't bother probing for modes we know we won't use. */
parport_PS2_supported(struct parport * pb)1828 static int parport_PS2_supported(struct parport *pb) { return 0; }
1829 #ifdef CONFIG_PARPORT_PC_FIFO
parport_ECP_supported(struct parport * pb)1830 static int parport_ECP_supported(struct parport *pb)
1831 {
1832 return 0;
1833 }
1834 #endif
parport_EPP_supported(struct parport * pb)1835 static int parport_EPP_supported(struct parport *pb)
1836 {
1837 return 0;
1838 }
1839
parport_ECPEPP_supported(struct parport * pb)1840 static int parport_ECPEPP_supported(struct parport *pb)
1841 {
1842 return 0;
1843 }
1844
parport_ECPPS2_supported(struct parport * pb)1845 static int parport_ECPPS2_supported(struct parport *pb)
1846 {
1847 return 0;
1848 }
1849
1850 #endif /* No IEEE 1284 support */
1851
1852 /* --- IRQ detection -------------------------------------- */
1853
1854 /* Only if supports ECP mode */
programmable_irq_support(struct parport * pb)1855 static int programmable_irq_support(struct parport *pb)
1856 {
1857 int irq, intrLine;
1858 unsigned char oecr = inb(ECONTROL(pb));
1859 static const int lookup[8] = {
1860 PARPORT_IRQ_NONE, 7, 9, 10, 11, 14, 15, 5
1861 };
1862
1863 ECR_WRITE(pb, ECR_CNF << 5); /* Configuration MODE */
1864
1865 intrLine = (inb(CONFIGB(pb)) >> 3) & 0x07;
1866 irq = lookup[intrLine];
1867
1868 ECR_WRITE(pb, oecr);
1869 return irq;
1870 }
1871
irq_probe_ECP(struct parport * pb)1872 static int irq_probe_ECP(struct parport *pb)
1873 {
1874 int i;
1875 unsigned long irqs;
1876
1877 irqs = probe_irq_on();
1878
1879 ECR_WRITE(pb, ECR_SPP << 5); /* Reset FIFO */
1880 ECR_WRITE(pb, (ECR_TST << 5) | 0x04);
1881 ECR_WRITE(pb, ECR_TST << 5);
1882
1883 /* If Full FIFO sure that writeIntrThreshold is generated */
1884 for (i = 0; i < 1024 && !(inb(ECONTROL(pb)) & 0x02) ; i++)
1885 outb(0xaa, FIFO(pb));
1886
1887 pb->irq = probe_irq_off(irqs);
1888 ECR_WRITE(pb, ECR_SPP << 5);
1889
1890 if (pb->irq <= 0)
1891 pb->irq = PARPORT_IRQ_NONE;
1892
1893 return pb->irq;
1894 }
1895
1896 /*
1897 * This detection seems that only works in National Semiconductors
1898 * This doesn't work in SMC, LGS, and Winbond
1899 */
irq_probe_EPP(struct parport * pb)1900 static int irq_probe_EPP(struct parport *pb)
1901 {
1902 #ifndef ADVANCED_DETECT
1903 return PARPORT_IRQ_NONE;
1904 #else
1905 int irqs;
1906 unsigned char oecr;
1907
1908 if (pb->modes & PARPORT_MODE_PCECR)
1909 oecr = inb(ECONTROL(pb));
1910
1911 irqs = probe_irq_on();
1912
1913 if (pb->modes & PARPORT_MODE_PCECR)
1914 frob_econtrol(pb, 0x10, 0x10);
1915
1916 clear_epp_timeout(pb);
1917 parport_pc_frob_control(pb, 0x20, 0x20);
1918 parport_pc_frob_control(pb, 0x10, 0x10);
1919 clear_epp_timeout(pb);
1920
1921 /* Device isn't expecting an EPP read
1922 * and generates an IRQ.
1923 */
1924 parport_pc_read_epp(pb);
1925 udelay(20);
1926
1927 pb->irq = probe_irq_off(irqs);
1928 if (pb->modes & PARPORT_MODE_PCECR)
1929 ECR_WRITE(pb, oecr);
1930 parport_pc_write_control(pb, 0xc);
1931
1932 if (pb->irq <= 0)
1933 pb->irq = PARPORT_IRQ_NONE;
1934
1935 return pb->irq;
1936 #endif /* Advanced detection */
1937 }
1938
irq_probe_SPP(struct parport * pb)1939 static int irq_probe_SPP(struct parport *pb)
1940 {
1941 /* Don't even try to do this. */
1942 return PARPORT_IRQ_NONE;
1943 }
1944
1945 /* We will attempt to share interrupt requests since other devices
1946 * such as sound cards and network cards seem to like using the
1947 * printer IRQs.
1948 *
1949 * When ECP is available we can autoprobe for IRQs.
1950 * NOTE: If we can autoprobe it, we can register the IRQ.
1951 */
parport_irq_probe(struct parport * pb)1952 static int parport_irq_probe(struct parport *pb)
1953 {
1954 struct parport_pc_private *priv = pb->private_data;
1955
1956 if (priv->ecr) {
1957 pb->irq = programmable_irq_support(pb);
1958
1959 if (pb->irq == PARPORT_IRQ_NONE)
1960 pb->irq = irq_probe_ECP(pb);
1961 }
1962
1963 if ((pb->irq == PARPORT_IRQ_NONE) && priv->ecr &&
1964 (pb->modes & PARPORT_MODE_EPP))
1965 pb->irq = irq_probe_EPP(pb);
1966
1967 clear_epp_timeout(pb);
1968
1969 if (pb->irq == PARPORT_IRQ_NONE && (pb->modes & PARPORT_MODE_EPP))
1970 pb->irq = irq_probe_EPP(pb);
1971
1972 clear_epp_timeout(pb);
1973
1974 if (pb->irq == PARPORT_IRQ_NONE)
1975 pb->irq = irq_probe_SPP(pb);
1976
1977 if (pb->irq == PARPORT_IRQ_NONE)
1978 pb->irq = get_superio_irq(pb);
1979
1980 return pb->irq;
1981 }
1982
1983 /* --- DMA detection -------------------------------------- */
1984
1985 /* Only if chipset conforms to ECP ISA Interface Standard */
programmable_dma_support(struct parport * p)1986 static int programmable_dma_support(struct parport *p)
1987 {
1988 unsigned char oecr = inb(ECONTROL(p));
1989 int dma;
1990
1991 frob_set_mode(p, ECR_CNF);
1992
1993 dma = inb(CONFIGB(p)) & 0x07;
1994 /* 000: Indicates jumpered 8-bit DMA if read-only.
1995 100: Indicates jumpered 16-bit DMA if read-only. */
1996 if ((dma & 0x03) == 0)
1997 dma = PARPORT_DMA_NONE;
1998
1999 ECR_WRITE(p, oecr);
2000 return dma;
2001 }
2002
parport_dma_probe(struct parport * p)2003 static int parport_dma_probe(struct parport *p)
2004 {
2005 const struct parport_pc_private *priv = p->private_data;
2006 if (priv->ecr) /* ask ECP chipset first */
2007 p->dma = programmable_dma_support(p);
2008 if (p->dma == PARPORT_DMA_NONE) {
2009 /* ask known Super-IO chips proper, although these
2010 claim ECP compatible, some don't report their DMA
2011 conforming to ECP standards */
2012 p->dma = get_superio_dma(p);
2013 }
2014
2015 return p->dma;
2016 }
2017
2018 /* --- Initialisation code -------------------------------- */
2019
2020 static LIST_HEAD(ports_list);
2021 static DEFINE_SPINLOCK(ports_lock);
2022
parport_pc_probe_port(unsigned long int base,unsigned long int base_hi,int irq,int dma,struct device * dev,int irqflags)2023 struct parport *parport_pc_probe_port(unsigned long int base,
2024 unsigned long int base_hi,
2025 int irq, int dma,
2026 struct device *dev,
2027 int irqflags)
2028 {
2029 struct parport_pc_private *priv;
2030 struct parport_operations *ops;
2031 struct parport *p;
2032 int probedirq = PARPORT_IRQ_NONE;
2033 struct resource *base_res;
2034 struct resource *ECR_res = NULL;
2035 struct resource *EPP_res = NULL;
2036 struct platform_device *pdev = NULL;
2037 int ret;
2038
2039 if (!dev) {
2040 /* We need a physical device to attach to, but none was
2041 * provided. Create our own. */
2042 pdev = platform_device_register_simple("parport_pc",
2043 base, NULL, 0);
2044 if (IS_ERR(pdev))
2045 return NULL;
2046 dev = &pdev->dev;
2047
2048 ret = dma_coerce_mask_and_coherent(dev, DMA_BIT_MASK(24));
2049 if (ret) {
2050 dev_err(dev, "Unable to set coherent dma mask: disabling DMA\n");
2051 dma = PARPORT_DMA_NONE;
2052 }
2053 }
2054
2055 ops = kmalloc(sizeof(struct parport_operations), GFP_KERNEL);
2056 if (!ops)
2057 goto out1;
2058
2059 priv = kmalloc(sizeof(struct parport_pc_private), GFP_KERNEL);
2060 if (!priv)
2061 goto out2;
2062
2063 /* a misnomer, actually - it's allocate and reserve parport number */
2064 p = parport_register_port(base, irq, dma, ops);
2065 if (!p)
2066 goto out3;
2067
2068 base_res = request_region(base, 3, p->name);
2069 if (!base_res)
2070 goto out4;
2071
2072 memcpy(ops, &parport_pc_ops, sizeof(struct parport_operations));
2073 priv->ctr = 0xc;
2074 priv->ctr_writable = ~0x10;
2075 priv->ecr = 0;
2076 priv->fifo_depth = 0;
2077 priv->dma_buf = NULL;
2078 priv->dma_handle = 0;
2079 INIT_LIST_HEAD(&priv->list);
2080 priv->port = p;
2081
2082 p->dev = dev;
2083 p->base_hi = base_hi;
2084 p->modes = PARPORT_MODE_PCSPP | PARPORT_MODE_SAFEININT;
2085 p->private_data = priv;
2086
2087 if (base_hi) {
2088 ECR_res = request_region(base_hi, 3, p->name);
2089 if (ECR_res)
2090 parport_ECR_present(p);
2091 }
2092
2093 if (base != 0x3bc) {
2094 EPP_res = request_region(base+0x3, 5, p->name);
2095 if (EPP_res)
2096 if (!parport_EPP_supported(p))
2097 parport_ECPEPP_supported(p);
2098 }
2099 if (!parport_SPP_supported(p))
2100 /* No port. */
2101 goto out5;
2102 if (priv->ecr)
2103 parport_ECPPS2_supported(p);
2104 else
2105 parport_PS2_supported(p);
2106
2107 p->size = (p->modes & PARPORT_MODE_EPP) ? 8 : 3;
2108
2109 printk(KERN_INFO "%s: PC-style at 0x%lx", p->name, p->base);
2110 if (p->base_hi && priv->ecr)
2111 printk(KERN_CONT " (0x%lx)", p->base_hi);
2112 if (p->irq == PARPORT_IRQ_AUTO) {
2113 p->irq = PARPORT_IRQ_NONE;
2114 parport_irq_probe(p);
2115 } else if (p->irq == PARPORT_IRQ_PROBEONLY) {
2116 p->irq = PARPORT_IRQ_NONE;
2117 parport_irq_probe(p);
2118 probedirq = p->irq;
2119 p->irq = PARPORT_IRQ_NONE;
2120 }
2121 if (p->irq != PARPORT_IRQ_NONE) {
2122 printk(KERN_CONT ", irq %d", p->irq);
2123 priv->ctr_writable |= 0x10;
2124
2125 if (p->dma == PARPORT_DMA_AUTO) {
2126 p->dma = PARPORT_DMA_NONE;
2127 parport_dma_probe(p);
2128 }
2129 }
2130 if (p->dma == PARPORT_DMA_AUTO) /* To use DMA, giving the irq
2131 is mandatory (see above) */
2132 p->dma = PARPORT_DMA_NONE;
2133
2134 #ifdef CONFIG_PARPORT_PC_FIFO
2135 if (parport_ECP_supported(p) &&
2136 p->dma != PARPORT_DMA_NOFIFO &&
2137 priv->fifo_depth > 0 && p->irq != PARPORT_IRQ_NONE) {
2138 p->modes |= PARPORT_MODE_ECP | PARPORT_MODE_COMPAT;
2139 p->ops->compat_write_data = parport_pc_compat_write_block_pio;
2140 #ifdef CONFIG_PARPORT_1284
2141 p->ops->ecp_write_data = parport_pc_ecp_write_block_pio;
2142 /* currently broken, but working on it.. (FB) */
2143 /* p->ops->ecp_read_data = parport_pc_ecp_read_block_pio; */
2144 #endif /* IEEE 1284 support */
2145 if (p->dma != PARPORT_DMA_NONE) {
2146 printk(KERN_CONT ", dma %d", p->dma);
2147 p->modes |= PARPORT_MODE_DMA;
2148 } else
2149 printk(KERN_CONT ", using FIFO");
2150 } else
2151 /* We can't use the DMA channel after all. */
2152 p->dma = PARPORT_DMA_NONE;
2153 #endif /* Allowed to use FIFO/DMA */
2154
2155 printk(KERN_CONT " [");
2156
2157 #define printmode(x) \
2158 {\
2159 if (p->modes & PARPORT_MODE_##x) {\
2160 printk(KERN_CONT "%s%s", f ? "," : "", #x);\
2161 f++;\
2162 } \
2163 }
2164
2165 {
2166 int f = 0;
2167 printmode(PCSPP);
2168 printmode(TRISTATE);
2169 printmode(COMPAT)
2170 printmode(EPP);
2171 printmode(ECP);
2172 printmode(DMA);
2173 }
2174 #undef printmode
2175 #ifndef CONFIG_PARPORT_1284
2176 printk(KERN_CONT "(,...)");
2177 #endif /* CONFIG_PARPORT_1284 */
2178 printk(KERN_CONT "]\n");
2179 if (probedirq != PARPORT_IRQ_NONE)
2180 printk(KERN_INFO "%s: irq %d detected\n", p->name, probedirq);
2181
2182 /* If No ECP release the ports grabbed above. */
2183 if (ECR_res && (p->modes & PARPORT_MODE_ECP) == 0) {
2184 release_region(base_hi, 3);
2185 ECR_res = NULL;
2186 }
2187 /* Likewise for EEP ports */
2188 if (EPP_res && (p->modes & PARPORT_MODE_EPP) == 0) {
2189 release_region(base+3, 5);
2190 EPP_res = NULL;
2191 }
2192 if (p->irq != PARPORT_IRQ_NONE) {
2193 if (request_irq(p->irq, parport_irq_handler,
2194 irqflags, p->name, p)) {
2195 printk(KERN_WARNING "%s: irq %d in use, "
2196 "resorting to polled operation\n",
2197 p->name, p->irq);
2198 p->irq = PARPORT_IRQ_NONE;
2199 p->dma = PARPORT_DMA_NONE;
2200 }
2201
2202 #ifdef CONFIG_PARPORT_PC_FIFO
2203 #ifdef HAS_DMA
2204 if (p->dma != PARPORT_DMA_NONE) {
2205 if (request_dma(p->dma, p->name)) {
2206 printk(KERN_WARNING "%s: dma %d in use, "
2207 "resorting to PIO operation\n",
2208 p->name, p->dma);
2209 p->dma = PARPORT_DMA_NONE;
2210 } else {
2211 priv->dma_buf =
2212 dma_alloc_coherent(dev,
2213 PAGE_SIZE,
2214 &priv->dma_handle,
2215 GFP_KERNEL);
2216 if (!priv->dma_buf) {
2217 printk(KERN_WARNING "%s: "
2218 "cannot get buffer for DMA, "
2219 "resorting to PIO operation\n",
2220 p->name);
2221 free_dma(p->dma);
2222 p->dma = PARPORT_DMA_NONE;
2223 }
2224 }
2225 }
2226 #endif
2227 #endif
2228 }
2229
2230 /* Done probing. Now put the port into a sensible start-up state. */
2231 if (priv->ecr)
2232 /*
2233 * Put the ECP detected port in PS2 mode.
2234 * Do this also for ports that have ECR but don't do ECP.
2235 */
2236 ECR_WRITE(p, 0x34);
2237
2238 parport_pc_write_data(p, 0);
2239 parport_pc_data_forward(p);
2240
2241 /* Now that we've told the sharing engine about the port, and
2242 found out its characteristics, let the high-level drivers
2243 know about it. */
2244 spin_lock(&ports_lock);
2245 list_add(&priv->list, &ports_list);
2246 spin_unlock(&ports_lock);
2247 parport_announce_port(p);
2248
2249 return p;
2250
2251 out5:
2252 if (ECR_res)
2253 release_region(base_hi, 3);
2254 if (EPP_res)
2255 release_region(base+0x3, 5);
2256 release_region(base, 3);
2257 out4:
2258 parport_del_port(p);
2259 out3:
2260 kfree(priv);
2261 out2:
2262 kfree(ops);
2263 out1:
2264 if (pdev)
2265 platform_device_unregister(pdev);
2266 return NULL;
2267 }
2268 EXPORT_SYMBOL(parport_pc_probe_port);
2269
parport_pc_unregister_port(struct parport * p)2270 void parport_pc_unregister_port(struct parport *p)
2271 {
2272 struct parport_pc_private *priv = p->private_data;
2273 struct parport_operations *ops = p->ops;
2274
2275 parport_remove_port(p);
2276 spin_lock(&ports_lock);
2277 list_del_init(&priv->list);
2278 spin_unlock(&ports_lock);
2279 #if defined(CONFIG_PARPORT_PC_FIFO) && defined(HAS_DMA)
2280 if (p->dma != PARPORT_DMA_NONE)
2281 free_dma(p->dma);
2282 #endif
2283 if (p->irq != PARPORT_IRQ_NONE)
2284 free_irq(p->irq, p);
2285 release_region(p->base, 3);
2286 if (p->size > 3)
2287 release_region(p->base + 3, p->size - 3);
2288 if (p->modes & PARPORT_MODE_ECP)
2289 release_region(p->base_hi, 3);
2290 #if defined(CONFIG_PARPORT_PC_FIFO) && defined(HAS_DMA)
2291 if (priv->dma_buf)
2292 dma_free_coherent(p->physport->dev, PAGE_SIZE,
2293 priv->dma_buf,
2294 priv->dma_handle);
2295 #endif
2296 kfree(p->private_data);
2297 parport_del_port(p);
2298 kfree(ops); /* hope no-one cached it */
2299 }
2300 EXPORT_SYMBOL(parport_pc_unregister_port);
2301
2302 #ifdef CONFIG_PCI
2303
2304 /* ITE support maintained by Rich Liu <richliu@poorman.org> */
sio_ite_8872_probe(struct pci_dev * pdev,int autoirq,int autodma,const struct parport_pc_via_data * via)2305 static int sio_ite_8872_probe(struct pci_dev *pdev, int autoirq, int autodma,
2306 const struct parport_pc_via_data *via)
2307 {
2308 short inta_addr[6] = { 0x2A0, 0x2C0, 0x220, 0x240, 0x1E0 };
2309 u32 ite8872set;
2310 u32 ite8872_lpt, ite8872_lpthi;
2311 u8 ite8872_irq, type;
2312 int irq;
2313 int i;
2314
2315 DPRINTK(KERN_DEBUG "sio_ite_8872_probe()\n");
2316
2317 /* make sure which one chip */
2318 for (i = 0; i < 5; i++) {
2319 if (request_region(inta_addr[i], 32, "it887x")) {
2320 int test;
2321 pci_write_config_dword(pdev, 0x60,
2322 0xe5000000 | inta_addr[i]);
2323 pci_write_config_dword(pdev, 0x78,
2324 0x00000000 | inta_addr[i]);
2325 test = inb(inta_addr[i]);
2326 if (test != 0xff)
2327 break;
2328 release_region(inta_addr[i], 32);
2329 }
2330 }
2331 if (i >= 5) {
2332 printk(KERN_INFO "parport_pc: cannot find ITE8872 INTA\n");
2333 return 0;
2334 }
2335
2336 type = inb(inta_addr[i] + 0x18);
2337 type &= 0x0f;
2338
2339 switch (type) {
2340 case 0x2:
2341 printk(KERN_INFO "parport_pc: ITE8871 found (1P)\n");
2342 ite8872set = 0x64200000;
2343 break;
2344 case 0xa:
2345 printk(KERN_INFO "parport_pc: ITE8875 found (1P)\n");
2346 ite8872set = 0x64200000;
2347 break;
2348 case 0xe:
2349 printk(KERN_INFO "parport_pc: ITE8872 found (2S1P)\n");
2350 ite8872set = 0x64e00000;
2351 break;
2352 case 0x6:
2353 printk(KERN_INFO "parport_pc: ITE8873 found (1S)\n");
2354 release_region(inta_addr[i], 32);
2355 return 0;
2356 case 0x8:
2357 printk(KERN_INFO "parport_pc: ITE8874 found (2S)\n");
2358 release_region(inta_addr[i], 32);
2359 return 0;
2360 default:
2361 printk(KERN_INFO "parport_pc: unknown ITE887x\n");
2362 printk(KERN_INFO "parport_pc: please mail 'lspci -nvv' "
2363 "output to Rich.Liu@ite.com.tw\n");
2364 release_region(inta_addr[i], 32);
2365 return 0;
2366 }
2367
2368 pci_read_config_byte(pdev, 0x3c, &ite8872_irq);
2369 pci_read_config_dword(pdev, 0x1c, &ite8872_lpt);
2370 ite8872_lpt &= 0x0000ff00;
2371 pci_read_config_dword(pdev, 0x20, &ite8872_lpthi);
2372 ite8872_lpthi &= 0x0000ff00;
2373 pci_write_config_dword(pdev, 0x6c, 0xe3000000 | ite8872_lpt);
2374 pci_write_config_dword(pdev, 0x70, 0xe3000000 | ite8872_lpthi);
2375 pci_write_config_dword(pdev, 0x80, (ite8872_lpthi<<16) | ite8872_lpt);
2376 /* SET SPP&EPP , Parallel Port NO DMA , Enable All Function */
2377 /* SET Parallel IRQ */
2378 pci_write_config_dword(pdev, 0x9c,
2379 ite8872set | (ite8872_irq * 0x11111));
2380
2381 DPRINTK(KERN_DEBUG "ITE887x: The IRQ is %d.\n", ite8872_irq);
2382 DPRINTK(KERN_DEBUG "ITE887x: The PARALLEL I/O port is 0x%x.\n",
2383 ite8872_lpt);
2384 DPRINTK(KERN_DEBUG "ITE887x: The PARALLEL I/O porthi is 0x%x.\n",
2385 ite8872_lpthi);
2386
2387 /* Let the user (or defaults) steer us away from interrupts */
2388 irq = ite8872_irq;
2389 if (autoirq != PARPORT_IRQ_AUTO)
2390 irq = PARPORT_IRQ_NONE;
2391
2392 /*
2393 * Release the resource so that parport_pc_probe_port can get it.
2394 */
2395 release_region(inta_addr[i], 32);
2396 if (parport_pc_probe_port(ite8872_lpt, ite8872_lpthi,
2397 irq, PARPORT_DMA_NONE, &pdev->dev, 0)) {
2398 printk(KERN_INFO
2399 "parport_pc: ITE 8872 parallel port: io=0x%X",
2400 ite8872_lpt);
2401 if (irq != PARPORT_IRQ_NONE)
2402 pr_cont(", irq=%d", irq);
2403 pr_cont("\n");
2404 return 1;
2405 }
2406
2407 return 0;
2408 }
2409
2410 /* VIA 8231 support by Pavel Fedin <sonic_amiga@rambler.ru>
2411 based on VIA 686a support code by Jeff Garzik <jgarzik@pobox.com> */
2412 static int parport_init_mode;
2413
2414 /* Data for two known VIA chips */
2415 static struct parport_pc_via_data via_686a_data = {
2416 0x51,
2417 0x50,
2418 0x85,
2419 0x02,
2420 0xE2,
2421 0xF0,
2422 0xE6
2423 };
2424 static struct parport_pc_via_data via_8231_data = {
2425 0x45,
2426 0x44,
2427 0x50,
2428 0x04,
2429 0xF2,
2430 0xFA,
2431 0xF6
2432 };
2433
sio_via_probe(struct pci_dev * pdev,int autoirq,int autodma,const struct parport_pc_via_data * via)2434 static int sio_via_probe(struct pci_dev *pdev, int autoirq, int autodma,
2435 const struct parport_pc_via_data *via)
2436 {
2437 u8 tmp, tmp2, siofunc;
2438 u8 ppcontrol = 0;
2439 int dma, irq;
2440 unsigned port1, port2;
2441 unsigned have_epp = 0;
2442
2443 printk(KERN_DEBUG "parport_pc: VIA 686A/8231 detected\n");
2444
2445 switch (parport_init_mode) {
2446 case 1:
2447 printk(KERN_DEBUG "parport_pc: setting SPP mode\n");
2448 siofunc = VIA_FUNCTION_PARPORT_SPP;
2449 break;
2450 case 2:
2451 printk(KERN_DEBUG "parport_pc: setting PS/2 mode\n");
2452 siofunc = VIA_FUNCTION_PARPORT_SPP;
2453 ppcontrol = VIA_PARPORT_BIDIR;
2454 break;
2455 case 3:
2456 printk(KERN_DEBUG "parport_pc: setting EPP mode\n");
2457 siofunc = VIA_FUNCTION_PARPORT_EPP;
2458 ppcontrol = VIA_PARPORT_BIDIR;
2459 have_epp = 1;
2460 break;
2461 case 4:
2462 printk(KERN_DEBUG "parport_pc: setting ECP mode\n");
2463 siofunc = VIA_FUNCTION_PARPORT_ECP;
2464 ppcontrol = VIA_PARPORT_BIDIR;
2465 break;
2466 case 5:
2467 printk(KERN_DEBUG "parport_pc: setting EPP+ECP mode\n");
2468 siofunc = VIA_FUNCTION_PARPORT_ECP;
2469 ppcontrol = VIA_PARPORT_BIDIR|VIA_PARPORT_ECPEPP;
2470 have_epp = 1;
2471 break;
2472 default:
2473 printk(KERN_DEBUG
2474 "parport_pc: probing current configuration\n");
2475 siofunc = VIA_FUNCTION_PROBE;
2476 break;
2477 }
2478 /*
2479 * unlock super i/o configuration
2480 */
2481 pci_read_config_byte(pdev, via->via_pci_superio_config_reg, &tmp);
2482 tmp |= via->via_pci_superio_config_data;
2483 pci_write_config_byte(pdev, via->via_pci_superio_config_reg, tmp);
2484
2485 /* Bits 1-0: Parallel Port Mode / Enable */
2486 outb(via->viacfg_function, VIA_CONFIG_INDEX);
2487 tmp = inb(VIA_CONFIG_DATA);
2488 /* Bit 5: EPP+ECP enable; bit 7: PS/2 bidirectional port enable */
2489 outb(via->viacfg_parport_control, VIA_CONFIG_INDEX);
2490 tmp2 = inb(VIA_CONFIG_DATA);
2491 if (siofunc == VIA_FUNCTION_PROBE) {
2492 siofunc = tmp & VIA_FUNCTION_PARPORT_DISABLE;
2493 ppcontrol = tmp2;
2494 } else {
2495 tmp &= ~VIA_FUNCTION_PARPORT_DISABLE;
2496 tmp |= siofunc;
2497 outb(via->viacfg_function, VIA_CONFIG_INDEX);
2498 outb(tmp, VIA_CONFIG_DATA);
2499 tmp2 &= ~(VIA_PARPORT_BIDIR|VIA_PARPORT_ECPEPP);
2500 tmp2 |= ppcontrol;
2501 outb(via->viacfg_parport_control, VIA_CONFIG_INDEX);
2502 outb(tmp2, VIA_CONFIG_DATA);
2503 }
2504
2505 /* Parallel Port I/O Base Address, bits 9-2 */
2506 outb(via->viacfg_parport_base, VIA_CONFIG_INDEX);
2507 port1 = inb(VIA_CONFIG_DATA) << 2;
2508
2509 printk(KERN_DEBUG "parport_pc: Current parallel port base: 0x%X\n",
2510 port1);
2511 if (port1 == 0x3BC && have_epp) {
2512 outb(via->viacfg_parport_base, VIA_CONFIG_INDEX);
2513 outb((0x378 >> 2), VIA_CONFIG_DATA);
2514 printk(KERN_DEBUG
2515 "parport_pc: Parallel port base changed to 0x378\n");
2516 port1 = 0x378;
2517 }
2518
2519 /*
2520 * lock super i/o configuration
2521 */
2522 pci_read_config_byte(pdev, via->via_pci_superio_config_reg, &tmp);
2523 tmp &= ~via->via_pci_superio_config_data;
2524 pci_write_config_byte(pdev, via->via_pci_superio_config_reg, tmp);
2525
2526 if (siofunc == VIA_FUNCTION_PARPORT_DISABLE) {
2527 printk(KERN_INFO "parport_pc: VIA parallel port disabled in BIOS\n");
2528 return 0;
2529 }
2530
2531 /* Bits 7-4: PnP Routing for Parallel Port IRQ */
2532 pci_read_config_byte(pdev, via->via_pci_parport_irq_reg, &tmp);
2533 irq = ((tmp & VIA_IRQCONTROL_PARALLEL) >> 4);
2534
2535 if (siofunc == VIA_FUNCTION_PARPORT_ECP) {
2536 /* Bits 3-2: PnP Routing for Parallel Port DMA */
2537 pci_read_config_byte(pdev, via->via_pci_parport_dma_reg, &tmp);
2538 dma = ((tmp & VIA_DMACONTROL_PARALLEL) >> 2);
2539 } else
2540 /* if ECP not enabled, DMA is not enabled, assumed
2541 bogus 'dma' value */
2542 dma = PARPORT_DMA_NONE;
2543
2544 /* Let the user (or defaults) steer us away from interrupts and DMA */
2545 if (autoirq == PARPORT_IRQ_NONE) {
2546 irq = PARPORT_IRQ_NONE;
2547 dma = PARPORT_DMA_NONE;
2548 }
2549 if (autodma == PARPORT_DMA_NONE)
2550 dma = PARPORT_DMA_NONE;
2551
2552 switch (port1) {
2553 case 0x3bc:
2554 port2 = 0x7bc; break;
2555 case 0x378:
2556 port2 = 0x778; break;
2557 case 0x278:
2558 port2 = 0x678; break;
2559 default:
2560 printk(KERN_INFO
2561 "parport_pc: Weird VIA parport base 0x%X, ignoring\n",
2562 port1);
2563 return 0;
2564 }
2565
2566 /* filter bogus IRQs */
2567 switch (irq) {
2568 case 0:
2569 case 2:
2570 case 8:
2571 case 13:
2572 irq = PARPORT_IRQ_NONE;
2573 break;
2574
2575 default: /* do nothing */
2576 break;
2577 }
2578
2579 /* finally, do the probe with values obtained */
2580 if (parport_pc_probe_port(port1, port2, irq, dma, &pdev->dev, 0)) {
2581 printk(KERN_INFO
2582 "parport_pc: VIA parallel port: io=0x%X", port1);
2583 if (irq != PARPORT_IRQ_NONE)
2584 pr_cont(", irq=%d", irq);
2585 if (dma != PARPORT_DMA_NONE)
2586 pr_cont(", dma=%d", dma);
2587 pr_cont("\n");
2588 return 1;
2589 }
2590
2591 printk(KERN_WARNING "parport_pc: Strange, can't probe VIA parallel port: io=0x%X, irq=%d, dma=%d\n",
2592 port1, irq, dma);
2593 return 0;
2594 }
2595
2596
2597 enum parport_pc_sio_types {
2598 sio_via_686a = 0, /* Via VT82C686A motherboard Super I/O */
2599 sio_via_8231, /* Via VT8231 south bridge integrated Super IO */
2600 sio_ite_8872,
2601 last_sio
2602 };
2603
2604 /* each element directly indexed from enum list, above */
2605 static struct parport_pc_superio {
2606 int (*probe) (struct pci_dev *pdev, int autoirq, int autodma,
2607 const struct parport_pc_via_data *via);
2608 const struct parport_pc_via_data *via;
2609 } parport_pc_superio_info[] = {
2610 { sio_via_probe, &via_686a_data, },
2611 { sio_via_probe, &via_8231_data, },
2612 { sio_ite_8872_probe, NULL, },
2613 };
2614
2615 enum parport_pc_pci_cards {
2616 siig_1p_10x = last_sio,
2617 siig_2p_10x,
2618 siig_1p_20x,
2619 siig_2p_20x,
2620 lava_parallel,
2621 lava_parallel_dual_a,
2622 lava_parallel_dual_b,
2623 boca_ioppar,
2624 plx_9050,
2625 timedia_4006a,
2626 timedia_4014,
2627 timedia_4008a,
2628 timedia_4018,
2629 timedia_9018a,
2630 syba_2p_epp,
2631 syba_1p_ecp,
2632 titan_010l,
2633 avlab_1p,
2634 avlab_2p,
2635 oxsemi_952,
2636 oxsemi_954,
2637 oxsemi_840,
2638 oxsemi_pcie_pport,
2639 aks_0100,
2640 mobility_pp,
2641 netmos_9705,
2642 netmos_9715,
2643 netmos_9755,
2644 netmos_9805,
2645 netmos_9815,
2646 netmos_9901,
2647 netmos_9865,
2648 quatech_sppxp100,
2649 wch_ch382l,
2650 };
2651
2652
2653 /* each element directly indexed from enum list, above
2654 * (but offset by last_sio) */
2655 static struct parport_pc_pci {
2656 int numports;
2657 struct { /* BAR (base address registers) numbers in the config
2658 space header */
2659 int lo;
2660 int hi;
2661 /* -1 if not there, >6 for offset-method (max BAR is 6) */
2662 } addr[4];
2663
2664 /* If set, this is called immediately after pci_enable_device.
2665 * If it returns non-zero, no probing will take place and the
2666 * ports will not be used. */
2667 int (*preinit_hook) (struct pci_dev *pdev, int autoirq, int autodma);
2668
2669 /* If set, this is called after probing for ports. If 'failed'
2670 * is non-zero we couldn't use any of the ports. */
2671 void (*postinit_hook) (struct pci_dev *pdev, int failed);
2672 } cards[] = {
2673 /* siig_1p_10x */ { 1, { { 2, 3 }, } },
2674 /* siig_2p_10x */ { 2, { { 2, 3 }, { 4, 5 }, } },
2675 /* siig_1p_20x */ { 1, { { 0, 1 }, } },
2676 /* siig_2p_20x */ { 2, { { 0, 1 }, { 2, 3 }, } },
2677 /* lava_parallel */ { 1, { { 0, -1 }, } },
2678 /* lava_parallel_dual_a */ { 1, { { 0, -1 }, } },
2679 /* lava_parallel_dual_b */ { 1, { { 0, -1 }, } },
2680 /* boca_ioppar */ { 1, { { 0, -1 }, } },
2681 /* plx_9050 */ { 2, { { 4, -1 }, { 5, -1 }, } },
2682 /* timedia_4006a */ { 1, { { 0, -1 }, } },
2683 /* timedia_4014 */ { 2, { { 0, -1 }, { 2, -1 }, } },
2684 /* timedia_4008a */ { 1, { { 0, 1 }, } },
2685 /* timedia_4018 */ { 2, { { 0, 1 }, { 2, 3 }, } },
2686 /* timedia_9018a */ { 2, { { 0, 1 }, { 2, 3 }, } },
2687 /* SYBA uses fixed offsets in
2688 a 1K io window */
2689 /* syba_2p_epp AP138B */ { 2, { { 0, 0x078 }, { 0, 0x178 }, } },
2690 /* syba_1p_ecp W83787 */ { 1, { { 0, 0x078 }, } },
2691 /* titan_010l */ { 1, { { 3, -1 }, } },
2692 /* avlab_1p */ { 1, { { 0, 1}, } },
2693 /* avlab_2p */ { 2, { { 0, 1}, { 2, 3 },} },
2694 /* The Oxford Semi cards are unusual: 954 doesn't support ECP,
2695 * and 840 locks up if you write 1 to bit 2! */
2696 /* oxsemi_952 */ { 1, { { 0, 1 }, } },
2697 /* oxsemi_954 */ { 1, { { 0, -1 }, } },
2698 /* oxsemi_840 */ { 1, { { 0, 1 }, } },
2699 /* oxsemi_pcie_pport */ { 1, { { 0, 1 }, } },
2700 /* aks_0100 */ { 1, { { 0, -1 }, } },
2701 /* mobility_pp */ { 1, { { 0, 1 }, } },
2702
2703 /* The netmos entries below are untested */
2704 /* netmos_9705 */ { 1, { { 0, -1 }, } },
2705 /* netmos_9715 */ { 2, { { 0, 1 }, { 2, 3 },} },
2706 /* netmos_9755 */ { 2, { { 0, 1 }, { 2, 3 },} },
2707 /* netmos_9805 */ { 1, { { 0, 1 }, } },
2708 /* netmos_9815 */ { 2, { { 0, 1 }, { 2, 3 }, } },
2709 /* netmos_9901 */ { 1, { { 0, -1 }, } },
2710 /* netmos_9865 */ { 1, { { 0, -1 }, } },
2711 /* quatech_sppxp100 */ { 1, { { 0, 1 }, } },
2712 /* wch_ch382l */ { 1, { { 2, -1 }, } },
2713 };
2714
2715 static const struct pci_device_id parport_pc_pci_tbl[] = {
2716 /* Super-IO onboard chips */
2717 { 0x1106, 0x0686, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sio_via_686a },
2718 { 0x1106, 0x8231, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sio_via_8231 },
2719 { PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8872,
2720 PCI_ANY_ID, PCI_ANY_ID, 0, 0, sio_ite_8872 },
2721
2722 /* PCI cards */
2723 { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1P_10x,
2724 PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_1p_10x },
2725 { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2P_10x,
2726 PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_2p_10x },
2727 { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1P_20x,
2728 PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_1p_20x },
2729 { PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2P_20x,
2730 PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_2p_20x },
2731 { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_PARALLEL,
2732 PCI_ANY_ID, PCI_ANY_ID, 0, 0, lava_parallel },
2733 { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_DUAL_PAR_A,
2734 PCI_ANY_ID, PCI_ANY_ID, 0, 0, lava_parallel_dual_a },
2735 { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_DUAL_PAR_B,
2736 PCI_ANY_ID, PCI_ANY_ID, 0, 0, lava_parallel_dual_b },
2737 { PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_BOCA_IOPPAR,
2738 PCI_ANY_ID, PCI_ANY_ID, 0, 0, boca_ioppar },
2739 { PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
2740 PCI_SUBVENDOR_ID_EXSYS, PCI_SUBDEVICE_ID_EXSYS_4014, 0, 0, plx_9050 },
2741 /* PCI_VENDOR_ID_TIMEDIA/SUNIX has many differing cards ...*/
2742 { 0x1409, 0x7268, 0x1409, 0x0101, 0, 0, timedia_4006a },
2743 { 0x1409, 0x7268, 0x1409, 0x0102, 0, 0, timedia_4014 },
2744 { 0x1409, 0x7268, 0x1409, 0x0103, 0, 0, timedia_4008a },
2745 { 0x1409, 0x7268, 0x1409, 0x0104, 0, 0, timedia_4018 },
2746 { 0x1409, 0x7268, 0x1409, 0x9018, 0, 0, timedia_9018a },
2747 { PCI_VENDOR_ID_SYBA, PCI_DEVICE_ID_SYBA_2P_EPP,
2748 PCI_ANY_ID, PCI_ANY_ID, 0, 0, syba_2p_epp },
2749 { PCI_VENDOR_ID_SYBA, PCI_DEVICE_ID_SYBA_1P_ECP,
2750 PCI_ANY_ID, PCI_ANY_ID, 0, 0, syba_1p_ecp },
2751 { PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_010L,
2752 PCI_ANY_ID, PCI_ANY_ID, 0, 0, titan_010l },
2753 /* PCI_VENDOR_ID_AVLAB/Intek21 has another bunch of cards ...*/
2754 /* AFAVLAB_TK9902 */
2755 { 0x14db, 0x2120, PCI_ANY_ID, PCI_ANY_ID, 0, 0, avlab_1p},
2756 { 0x14db, 0x2121, PCI_ANY_ID, PCI_ANY_ID, 0, 0, avlab_2p},
2757 { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI952PP,
2758 PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_952 },
2759 { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI954PP,
2760 PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_954 },
2761 { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_12PCI840,
2762 PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_840 },
2763 { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe840,
2764 PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport },
2765 { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe840_G,
2766 PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport },
2767 { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe952_0,
2768 PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport },
2769 { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe952_0_G,
2770 PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport },
2771 { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe952_1,
2772 PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport },
2773 { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe952_1_G,
2774 PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport },
2775 { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe952_1_U,
2776 PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport },
2777 { PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe952_1_GU,
2778 PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport },
2779 { PCI_VENDOR_ID_AKS, PCI_DEVICE_ID_AKS_ALADDINCARD,
2780 PCI_ANY_ID, PCI_ANY_ID, 0, 0, aks_0100 },
2781 { 0x14f2, 0x0121, PCI_ANY_ID, PCI_ANY_ID, 0, 0, mobility_pp },
2782 /* NetMos communication controllers */
2783 { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9705,
2784 PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9705 },
2785 { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9715,
2786 PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9715 },
2787 { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9755,
2788 PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9755 },
2789 { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9805,
2790 PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9805 },
2791 { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9815,
2792 PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9815 },
2793 { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9901,
2794 0xA000, 0x2000, 0, 0, netmos_9901 },
2795 { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9865,
2796 0xA000, 0x1000, 0, 0, netmos_9865 },
2797 { PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9865,
2798 0xA000, 0x2000, 0, 0, netmos_9865 },
2799 /* Quatech SPPXP-100 Parallel port PCI ExpressCard */
2800 { PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_SPPXP_100,
2801 PCI_ANY_ID, PCI_ANY_ID, 0, 0, quatech_sppxp100 },
2802 /* WCH CH382L PCI-E single parallel port card */
2803 { 0x1c00, 0x3050, 0x1c00, 0x3050, 0, 0, wch_ch382l },
2804 { 0, } /* terminate list */
2805 };
2806 MODULE_DEVICE_TABLE(pci, parport_pc_pci_tbl);
2807
2808 struct pci_parport_data {
2809 int num;
2810 struct parport *ports[2];
2811 };
2812
parport_pc_pci_probe(struct pci_dev * dev,const struct pci_device_id * id)2813 static int parport_pc_pci_probe(struct pci_dev *dev,
2814 const struct pci_device_id *id)
2815 {
2816 int err, count, n, i = id->driver_data;
2817 struct pci_parport_data *data;
2818
2819 if (i < last_sio)
2820 /* This is an onboard Super-IO and has already been probed */
2821 return 0;
2822
2823 /* This is a PCI card */
2824 i -= last_sio;
2825 count = 0;
2826 err = pci_enable_device(dev);
2827 if (err)
2828 return err;
2829
2830 data = kmalloc(sizeof(struct pci_parport_data), GFP_KERNEL);
2831 if (!data)
2832 return -ENOMEM;
2833
2834 if (cards[i].preinit_hook &&
2835 cards[i].preinit_hook(dev, PARPORT_IRQ_NONE, PARPORT_DMA_NONE)) {
2836 kfree(data);
2837 return -ENODEV;
2838 }
2839
2840 for (n = 0; n < cards[i].numports; n++) {
2841 int lo = cards[i].addr[n].lo;
2842 int hi = cards[i].addr[n].hi;
2843 int irq;
2844 unsigned long io_lo, io_hi;
2845 io_lo = pci_resource_start(dev, lo);
2846 io_hi = 0;
2847 if ((hi >= 0) && (hi <= 6))
2848 io_hi = pci_resource_start(dev, hi);
2849 else if (hi > 6)
2850 io_lo += hi; /* Reinterpret the meaning of
2851 "hi" as an offset (see SYBA
2852 def.) */
2853 /* TODO: test if sharing interrupts works */
2854 irq = dev->irq;
2855 if (irq == IRQ_NONE) {
2856 printk(KERN_DEBUG
2857 "PCI parallel port detected: %04x:%04x, I/O at %#lx(%#lx)\n",
2858 id->vendor, id->device, io_lo, io_hi);
2859 irq = PARPORT_IRQ_NONE;
2860 } else {
2861 printk(KERN_DEBUG
2862 "PCI parallel port detected: %04x:%04x, I/O at %#lx(%#lx), IRQ %d\n",
2863 id->vendor, id->device, io_lo, io_hi, irq);
2864 }
2865 data->ports[count] =
2866 parport_pc_probe_port(io_lo, io_hi, irq,
2867 PARPORT_DMA_NONE, &dev->dev,
2868 IRQF_SHARED);
2869 if (data->ports[count])
2870 count++;
2871 }
2872
2873 data->num = count;
2874
2875 if (cards[i].postinit_hook)
2876 cards[i].postinit_hook(dev, count == 0);
2877
2878 if (count) {
2879 pci_set_drvdata(dev, data);
2880 return 0;
2881 }
2882
2883 kfree(data);
2884
2885 return -ENODEV;
2886 }
2887
parport_pc_pci_remove(struct pci_dev * dev)2888 static void parport_pc_pci_remove(struct pci_dev *dev)
2889 {
2890 struct pci_parport_data *data = pci_get_drvdata(dev);
2891 int i;
2892
2893 if (data) {
2894 for (i = data->num - 1; i >= 0; i--)
2895 parport_pc_unregister_port(data->ports[i]);
2896
2897 kfree(data);
2898 }
2899 }
2900
2901 static struct pci_driver parport_pc_pci_driver = {
2902 .name = "parport_pc",
2903 .id_table = parport_pc_pci_tbl,
2904 .probe = parport_pc_pci_probe,
2905 .remove = parport_pc_pci_remove,
2906 };
2907
parport_pc_init_superio(int autoirq,int autodma)2908 static int __init parport_pc_init_superio(int autoirq, int autodma)
2909 {
2910 const struct pci_device_id *id;
2911 struct pci_dev *pdev = NULL;
2912 int ret = 0;
2913
2914 for_each_pci_dev(pdev) {
2915 id = pci_match_id(parport_pc_pci_tbl, pdev);
2916 if (id == NULL || id->driver_data >= last_sio)
2917 continue;
2918
2919 if (parport_pc_superio_info[id->driver_data].probe(
2920 pdev, autoirq, autodma,
2921 parport_pc_superio_info[id->driver_data].via)) {
2922 ret++;
2923 }
2924 }
2925
2926 return ret; /* number of devices found */
2927 }
2928 #else
2929 static struct pci_driver parport_pc_pci_driver;
parport_pc_init_superio(int autoirq,int autodma)2930 static int __init parport_pc_init_superio(int autoirq, int autodma)
2931 {
2932 return 0;
2933 }
2934 #endif /* CONFIG_PCI */
2935
2936 #ifdef CONFIG_PNP
2937
2938 static const struct pnp_device_id parport_pc_pnp_tbl[] = {
2939 /* Standard LPT Printer Port */
2940 {.id = "PNP0400", .driver_data = 0},
2941 /* ECP Printer Port */
2942 {.id = "PNP0401", .driver_data = 0},
2943 { }
2944 };
2945
2946 MODULE_DEVICE_TABLE(pnp, parport_pc_pnp_tbl);
2947
parport_pc_pnp_probe(struct pnp_dev * dev,const struct pnp_device_id * id)2948 static int parport_pc_pnp_probe(struct pnp_dev *dev,
2949 const struct pnp_device_id *id)
2950 {
2951 struct parport *pdata;
2952 unsigned long io_lo, io_hi;
2953 int dma, irq;
2954
2955 if (pnp_port_valid(dev, 0) &&
2956 !(pnp_port_flags(dev, 0) & IORESOURCE_DISABLED)) {
2957 io_lo = pnp_port_start(dev, 0);
2958 } else
2959 return -EINVAL;
2960
2961 if (pnp_port_valid(dev, 1) &&
2962 !(pnp_port_flags(dev, 1) & IORESOURCE_DISABLED)) {
2963 io_hi = pnp_port_start(dev, 1);
2964 } else
2965 io_hi = 0;
2966
2967 if (pnp_irq_valid(dev, 0) &&
2968 !(pnp_irq_flags(dev, 0) & IORESOURCE_DISABLED)) {
2969 irq = pnp_irq(dev, 0);
2970 } else
2971 irq = PARPORT_IRQ_NONE;
2972
2973 if (pnp_dma_valid(dev, 0) &&
2974 !(pnp_dma_flags(dev, 0) & IORESOURCE_DISABLED)) {
2975 dma = pnp_dma(dev, 0);
2976 } else
2977 dma = PARPORT_DMA_NONE;
2978
2979 dev_info(&dev->dev, "reported by %s\n", dev->protocol->name);
2980 pdata = parport_pc_probe_port(io_lo, io_hi, irq, dma, &dev->dev, 0);
2981 if (pdata == NULL)
2982 return -ENODEV;
2983
2984 pnp_set_drvdata(dev, pdata);
2985 return 0;
2986 }
2987
parport_pc_pnp_remove(struct pnp_dev * dev)2988 static void parport_pc_pnp_remove(struct pnp_dev *dev)
2989 {
2990 struct parport *pdata = (struct parport *)pnp_get_drvdata(dev);
2991 if (!pdata)
2992 return;
2993
2994 parport_pc_unregister_port(pdata);
2995 }
2996
2997 /* we only need the pnp layer to activate the device, at least for now */
2998 static struct pnp_driver parport_pc_pnp_driver = {
2999 .name = "parport_pc",
3000 .id_table = parport_pc_pnp_tbl,
3001 .probe = parport_pc_pnp_probe,
3002 .remove = parport_pc_pnp_remove,
3003 };
3004
3005 #else
3006 static struct pnp_driver parport_pc_pnp_driver;
3007 #endif /* CONFIG_PNP */
3008
parport_pc_platform_probe(struct platform_device * pdev)3009 static int parport_pc_platform_probe(struct platform_device *pdev)
3010 {
3011 /* Always succeed, the actual probing is done in
3012 * parport_pc_probe_port(). */
3013 return 0;
3014 }
3015
3016 static struct platform_driver parport_pc_platform_driver = {
3017 .driver = {
3018 .name = "parport_pc",
3019 },
3020 .probe = parport_pc_platform_probe,
3021 };
3022
3023 /* This is called by parport_pc_find_nonpci_ports (in asm/parport.h) */
3024 static int __attribute__((unused))
parport_pc_find_isa_ports(int autoirq,int autodma)3025 parport_pc_find_isa_ports(int autoirq, int autodma)
3026 {
3027 int count = 0;
3028
3029 if (parport_pc_probe_port(0x3bc, 0x7bc, autoirq, autodma, NULL, 0))
3030 count++;
3031 if (parport_pc_probe_port(0x378, 0x778, autoirq, autodma, NULL, 0))
3032 count++;
3033 if (parport_pc_probe_port(0x278, 0x678, autoirq, autodma, NULL, 0))
3034 count++;
3035
3036 return count;
3037 }
3038
3039 /* This function is called by parport_pc_init if the user didn't
3040 * specify any ports to probe. Its job is to find some ports. Order
3041 * is important here -- we want ISA ports to be registered first,
3042 * followed by PCI cards (for least surprise), but before that we want
3043 * to do chipset-specific tests for some onboard ports that we know
3044 * about.
3045 *
3046 * autoirq is PARPORT_IRQ_NONE, PARPORT_IRQ_AUTO, or PARPORT_IRQ_PROBEONLY
3047 * autodma is PARPORT_DMA_NONE or PARPORT_DMA_AUTO
3048 */
parport_pc_find_ports(int autoirq,int autodma)3049 static void __init parport_pc_find_ports(int autoirq, int autodma)
3050 {
3051 int count = 0, err;
3052
3053 #ifdef CONFIG_PARPORT_PC_SUPERIO
3054 detect_and_report_it87();
3055 detect_and_report_winbond();
3056 detect_and_report_smsc();
3057 #endif
3058
3059 /* Onboard SuperIO chipsets that show themselves on the PCI bus. */
3060 count += parport_pc_init_superio(autoirq, autodma);
3061
3062 /* PnP ports, skip detection if SuperIO already found them */
3063 if (!count) {
3064 err = pnp_register_driver(&parport_pc_pnp_driver);
3065 if (!err)
3066 pnp_registered_parport = 1;
3067 }
3068
3069 /* ISA ports and whatever (see asm/parport.h). */
3070 parport_pc_find_nonpci_ports(autoirq, autodma);
3071
3072 err = pci_register_driver(&parport_pc_pci_driver);
3073 if (!err)
3074 pci_registered_parport = 1;
3075 }
3076
3077 /*
3078 * Piles of crap below pretend to be a parser for module and kernel
3079 * parameters. Say "thank you" to whoever had come up with that
3080 * syntax and keep in mind that code below is a cleaned up version.
3081 */
3082
3083 static int __initdata io[PARPORT_PC_MAX_PORTS+1] = {
3084 [0 ... PARPORT_PC_MAX_PORTS] = 0
3085 };
3086 static int __initdata io_hi[PARPORT_PC_MAX_PORTS+1] = {
3087 [0 ... PARPORT_PC_MAX_PORTS] = PARPORT_IOHI_AUTO
3088 };
3089 static int __initdata dmaval[PARPORT_PC_MAX_PORTS] = {
3090 [0 ... PARPORT_PC_MAX_PORTS-1] = PARPORT_DMA_NONE
3091 };
3092 static int __initdata irqval[PARPORT_PC_MAX_PORTS] = {
3093 [0 ... PARPORT_PC_MAX_PORTS-1] = PARPORT_IRQ_PROBEONLY
3094 };
3095
parport_parse_param(const char * s,int * val,int automatic,int none,int nofifo)3096 static int __init parport_parse_param(const char *s, int *val,
3097 int automatic, int none, int nofifo)
3098 {
3099 if (!s)
3100 return 0;
3101 if (!strncmp(s, "auto", 4))
3102 *val = automatic;
3103 else if (!strncmp(s, "none", 4))
3104 *val = none;
3105 else if (nofifo && !strncmp(s, "nofifo", 6))
3106 *val = nofifo;
3107 else {
3108 char *ep;
3109 unsigned long r = simple_strtoul(s, &ep, 0);
3110 if (ep != s)
3111 *val = r;
3112 else {
3113 printk(KERN_ERR "parport: bad specifier `%s'\n", s);
3114 return -1;
3115 }
3116 }
3117 return 0;
3118 }
3119
parport_parse_irq(const char * irqstr,int * val)3120 static int __init parport_parse_irq(const char *irqstr, int *val)
3121 {
3122 return parport_parse_param(irqstr, val, PARPORT_IRQ_AUTO,
3123 PARPORT_IRQ_NONE, 0);
3124 }
3125
parport_parse_dma(const char * dmastr,int * val)3126 static int __init parport_parse_dma(const char *dmastr, int *val)
3127 {
3128 return parport_parse_param(dmastr, val, PARPORT_DMA_AUTO,
3129 PARPORT_DMA_NONE, PARPORT_DMA_NOFIFO);
3130 }
3131
3132 #ifdef CONFIG_PCI
parport_init_mode_setup(char * str)3133 static int __init parport_init_mode_setup(char *str)
3134 {
3135 printk(KERN_DEBUG
3136 "parport_pc.c: Specified parameter parport_init_mode=%s\n", str);
3137
3138 if (!strcmp(str, "spp"))
3139 parport_init_mode = 1;
3140 if (!strcmp(str, "ps2"))
3141 parport_init_mode = 2;
3142 if (!strcmp(str, "epp"))
3143 parport_init_mode = 3;
3144 if (!strcmp(str, "ecp"))
3145 parport_init_mode = 4;
3146 if (!strcmp(str, "ecpepp"))
3147 parport_init_mode = 5;
3148 return 1;
3149 }
3150 #endif
3151
3152 #ifdef MODULE
3153 static char *irq[PARPORT_PC_MAX_PORTS];
3154 static char *dma[PARPORT_PC_MAX_PORTS];
3155
3156 MODULE_PARM_DESC(io, "Base I/O address (SPP regs)");
3157 module_param_hw_array(io, int, ioport, NULL, 0);
3158 MODULE_PARM_DESC(io_hi, "Base I/O address (ECR)");
3159 module_param_hw_array(io_hi, int, ioport, NULL, 0);
3160 MODULE_PARM_DESC(irq, "IRQ line");
3161 module_param_hw_array(irq, charp, irq, NULL, 0);
3162 MODULE_PARM_DESC(dma, "DMA channel");
3163 module_param_hw_array(dma, charp, dma, NULL, 0);
3164 #if defined(CONFIG_PARPORT_PC_SUPERIO) || \
3165 (defined(CONFIG_PARPORT_1284) && defined(CONFIG_PARPORT_PC_FIFO))
3166 MODULE_PARM_DESC(verbose_probing, "Log chit-chat during initialisation");
3167 module_param(verbose_probing, int, 0644);
3168 #endif
3169 #ifdef CONFIG_PCI
3170 static char *init_mode;
3171 MODULE_PARM_DESC(init_mode,
3172 "Initialise mode for VIA VT8231 port (spp, ps2, epp, ecp or ecpepp)");
3173 module_param(init_mode, charp, 0);
3174 #endif
3175
parse_parport_params(void)3176 static int __init parse_parport_params(void)
3177 {
3178 unsigned int i;
3179 int val;
3180
3181 #ifdef CONFIG_PCI
3182 if (init_mode)
3183 parport_init_mode_setup(init_mode);
3184 #endif
3185
3186 for (i = 0; i < PARPORT_PC_MAX_PORTS && io[i]; i++) {
3187 if (parport_parse_irq(irq[i], &val))
3188 return 1;
3189 irqval[i] = val;
3190 if (parport_parse_dma(dma[i], &val))
3191 return 1;
3192 dmaval[i] = val;
3193 }
3194 if (!io[0]) {
3195 /* The user can make us use any IRQs or DMAs we find. */
3196 if (irq[0] && !parport_parse_irq(irq[0], &val))
3197 switch (val) {
3198 case PARPORT_IRQ_NONE:
3199 case PARPORT_IRQ_AUTO:
3200 irqval[0] = val;
3201 break;
3202 default:
3203 printk(KERN_WARNING
3204 "parport_pc: irq specified "
3205 "without base address. Use 'io=' "
3206 "to specify one\n");
3207 }
3208
3209 if (dma[0] && !parport_parse_dma(dma[0], &val))
3210 switch (val) {
3211 case PARPORT_DMA_NONE:
3212 case PARPORT_DMA_AUTO:
3213 dmaval[0] = val;
3214 break;
3215 default:
3216 printk(KERN_WARNING
3217 "parport_pc: dma specified "
3218 "without base address. Use 'io=' "
3219 "to specify one\n");
3220 }
3221 }
3222 return 0;
3223 }
3224
3225 #else
3226
3227 static int parport_setup_ptr __initdata;
3228
3229 /*
3230 * Acceptable parameters:
3231 *
3232 * parport=0
3233 * parport=auto
3234 * parport=0xBASE[,IRQ[,DMA]]
3235 *
3236 * IRQ/DMA may be numeric or 'auto' or 'none'
3237 */
parport_setup(char * str)3238 static int __init parport_setup(char *str)
3239 {
3240 char *endptr;
3241 char *sep;
3242 int val;
3243
3244 if (!str || !*str || (*str == '0' && !*(str+1))) {
3245 /* Disable parport if "parport=0" in cmdline */
3246 io[0] = PARPORT_DISABLE;
3247 return 1;
3248 }
3249
3250 if (!strncmp(str, "auto", 4)) {
3251 irqval[0] = PARPORT_IRQ_AUTO;
3252 dmaval[0] = PARPORT_DMA_AUTO;
3253 return 1;
3254 }
3255
3256 val = simple_strtoul(str, &endptr, 0);
3257 if (endptr == str) {
3258 printk(KERN_WARNING "parport=%s not understood\n", str);
3259 return 1;
3260 }
3261
3262 if (parport_setup_ptr == PARPORT_PC_MAX_PORTS) {
3263 printk(KERN_ERR "parport=%s ignored, too many ports\n", str);
3264 return 1;
3265 }
3266
3267 io[parport_setup_ptr] = val;
3268 irqval[parport_setup_ptr] = PARPORT_IRQ_NONE;
3269 dmaval[parport_setup_ptr] = PARPORT_DMA_NONE;
3270
3271 sep = strchr(str, ',');
3272 if (sep++) {
3273 if (parport_parse_irq(sep, &val))
3274 return 1;
3275 irqval[parport_setup_ptr] = val;
3276 sep = strchr(sep, ',');
3277 if (sep++) {
3278 if (parport_parse_dma(sep, &val))
3279 return 1;
3280 dmaval[parport_setup_ptr] = val;
3281 }
3282 }
3283 parport_setup_ptr++;
3284 return 1;
3285 }
3286
parse_parport_params(void)3287 static int __init parse_parport_params(void)
3288 {
3289 return io[0] == PARPORT_DISABLE;
3290 }
3291
3292 __setup("parport=", parport_setup);
3293
3294 /*
3295 * Acceptable parameters:
3296 *
3297 * parport_init_mode=[spp|ps2|epp|ecp|ecpepp]
3298 */
3299 #ifdef CONFIG_PCI
3300 __setup("parport_init_mode=", parport_init_mode_setup);
3301 #endif
3302 #endif
3303
3304 /* "Parser" ends here */
3305
parport_pc_init(void)3306 static int __init parport_pc_init(void)
3307 {
3308 int err;
3309
3310 if (parse_parport_params())
3311 return -EINVAL;
3312
3313 err = platform_driver_register(&parport_pc_platform_driver);
3314 if (err)
3315 return err;
3316
3317 if (io[0]) {
3318 int i;
3319 /* Only probe the ports we were given. */
3320 user_specified = 1;
3321 for (i = 0; i < PARPORT_PC_MAX_PORTS; i++) {
3322 if (!io[i])
3323 break;
3324 if (io_hi[i] == PARPORT_IOHI_AUTO)
3325 io_hi[i] = 0x400 + io[i];
3326 parport_pc_probe_port(io[i], io_hi[i],
3327 irqval[i], dmaval[i], NULL, 0);
3328 }
3329 } else
3330 parport_pc_find_ports(irqval[0], dmaval[0]);
3331
3332 return 0;
3333 }
3334
parport_pc_exit(void)3335 static void __exit parport_pc_exit(void)
3336 {
3337 if (pci_registered_parport)
3338 pci_unregister_driver(&parport_pc_pci_driver);
3339 if (pnp_registered_parport)
3340 pnp_unregister_driver(&parport_pc_pnp_driver);
3341 platform_driver_unregister(&parport_pc_platform_driver);
3342
3343 while (!list_empty(&ports_list)) {
3344 struct parport_pc_private *priv;
3345 struct parport *port;
3346 struct device *dev;
3347 priv = list_entry(ports_list.next,
3348 struct parport_pc_private, list);
3349 port = priv->port;
3350 dev = port->dev;
3351 parport_pc_unregister_port(port);
3352 if (dev && dev->bus == &platform_bus_type)
3353 platform_device_unregister(to_platform_device(dev));
3354 }
3355 }
3356
3357 MODULE_AUTHOR("Phil Blundell, Tim Waugh, others");
3358 MODULE_DESCRIPTION("PC-style parallel port driver");
3359 MODULE_LICENSE("GPL");
3360 module_init(parport_pc_init)
3361 module_exit(parport_pc_exit)
3362