1 /* Low-level parallel-port routines for 8255-based PC-style hardware.
2  *
3  * Authors: Phil Blundell <philb@gnu.org>
4  *          Tim Waugh <tim@cyberelk.demon.co.uk>
5  *	    Jose Renau <renau@acm.org>
6  *          David Campbell
7  *          Andrea Arcangeli
8  *
9  * based on work by Grant Guenther <grant@torque.net> and Phil Blundell.
10  *
11  * Cleaned up include files - Russell King <linux@arm.uk.linux.org>
12  * DMA support - Bert De Jonghe <bert@sophis.be>
13  * Many ECP bugs fixed.  Fred Barnes & Jamie Lokier, 1999
14  * More PCI support now conditional on CONFIG_PCI, 03/2001, Paul G.
15  * Various hacks, Fred Barnes, 04/2001
16  * Updated probing logic - Adam Belay <ambx1@neo.rr.com>
17  */
18 
19 /* This driver should work with any hardware that is broadly compatible
20  * with that in the IBM PC.  This applies to the majority of integrated
21  * I/O chipsets that are commonly available.  The expected register
22  * layout is:
23  *
24  *	base+0		data
25  *	base+1		status
26  *	base+2		control
27  *
28  * In addition, there are some optional registers:
29  *
30  *	base+3		EPP address
31  *	base+4		EPP data
32  *	base+0x400	ECP config A
33  *	base+0x401	ECP config B
34  *	base+0x402	ECP control
35  *
36  * All registers are 8 bits wide and read/write.  If your hardware differs
37  * only in register addresses (eg because your registers are on 32-bit
38  * word boundaries) then you can alter the constants in parport_pc.h to
39  * accommodate this.
40  *
41  * Note that the ECP registers may not start at offset 0x400 for PCI cards,
42  * but rather will start at port->base_hi.
43  */
44 
45 #include <linux/module.h>
46 #include <linux/init.h>
47 #include <linux/sched/signal.h>
48 #include <linux/delay.h>
49 #include <linux/errno.h>
50 #include <linux/interrupt.h>
51 #include <linux/ioport.h>
52 #include <linux/kernel.h>
53 #include <linux/slab.h>
54 #include <linux/dma-mapping.h>
55 #include <linux/pci.h>
56 #include <linux/pnp.h>
57 #include <linux/platform_device.h>
58 #include <linux/sysctl.h>
59 #include <linux/io.h>
60 #include <linux/uaccess.h>
61 
62 #include <asm/dma.h>
63 
64 #include <linux/parport.h>
65 #include <linux/parport_pc.h>
66 #include <linux/via.h>
67 #include <asm/parport.h>
68 
69 #define PARPORT_PC_MAX_PORTS PARPORT_MAX
70 
71 #ifdef CONFIG_ISA_DMA_API
72 #define HAS_DMA
73 #endif
74 
75 /* ECR modes */
76 #define ECR_SPP 00
77 #define ECR_PS2 01
78 #define ECR_PPF 02
79 #define ECR_ECP 03
80 #define ECR_EPP 04
81 #define ECR_VND 05
82 #define ECR_TST 06
83 #define ECR_CNF 07
84 #define ECR_MODE_MASK 0xe0
85 #define ECR_WRITE(p, v) frob_econtrol((p), 0xff, (v))
86 
87 #undef DEBUG
88 
89 #ifdef DEBUG
90 #define DPRINTK  printk
91 #else
92 #define DPRINTK(stuff...)
93 #endif
94 
95 
96 #define NR_SUPERIOS 3
97 static struct superio_struct {	/* For Super-IO chips autodetection */
98 	int io;
99 	int irq;
100 	int dma;
101 } superios[NR_SUPERIOS] = { {0,},};
102 
103 static int user_specified;
104 #if defined(CONFIG_PARPORT_PC_SUPERIO) || \
105        (defined(CONFIG_PARPORT_1284) && defined(CONFIG_PARPORT_PC_FIFO))
106 static int verbose_probing;
107 #endif
108 static int pci_registered_parport;
109 static int pnp_registered_parport;
110 
111 /* frob_control, but for ECR */
frob_econtrol(struct parport * pb,unsigned char m,unsigned char v)112 static void frob_econtrol(struct parport *pb, unsigned char m,
113 			   unsigned char v)
114 {
115 	unsigned char ectr = 0;
116 
117 	if (m != 0xff)
118 		ectr = inb(ECONTROL(pb));
119 
120 	DPRINTK(KERN_DEBUG "frob_econtrol(%02x,%02x): %02x -> %02x\n",
121 		m, v, ectr, (ectr & ~m) ^ v);
122 
123 	outb((ectr & ~m) ^ v, ECONTROL(pb));
124 }
125 
frob_set_mode(struct parport * p,int mode)126 static inline void frob_set_mode(struct parport *p, int mode)
127 {
128 	frob_econtrol(p, ECR_MODE_MASK, mode << 5);
129 }
130 
131 #ifdef CONFIG_PARPORT_PC_FIFO
132 /* Safely change the mode bits in the ECR
133    Returns:
134 	    0    : Success
135 	   -EBUSY: Could not drain FIFO in some finite amount of time,
136 		   mode not changed!
137  */
change_mode(struct parport * p,int m)138 static int change_mode(struct parport *p, int m)
139 {
140 	const struct parport_pc_private *priv = p->physport->private_data;
141 	unsigned char oecr;
142 	int mode;
143 
144 	DPRINTK(KERN_INFO "parport change_mode ECP-ISA to mode 0x%02x\n", m);
145 
146 	if (!priv->ecr) {
147 		printk(KERN_DEBUG "change_mode: but there's no ECR!\n");
148 		return 0;
149 	}
150 
151 	/* Bits <7:5> contain the mode. */
152 	oecr = inb(ECONTROL(p));
153 	mode = (oecr >> 5) & 0x7;
154 	if (mode == m)
155 		return 0;
156 
157 	if (mode >= 2 && !(priv->ctr & 0x20)) {
158 		/* This mode resets the FIFO, so we may
159 		 * have to wait for it to drain first. */
160 		unsigned long expire = jiffies + p->physport->cad->timeout;
161 		int counter;
162 		switch (mode) {
163 		case ECR_PPF: /* Parallel Port FIFO mode */
164 		case ECR_ECP: /* ECP Parallel Port mode */
165 			/* Busy wait for 200us */
166 			for (counter = 0; counter < 40; counter++) {
167 				if (inb(ECONTROL(p)) & 0x01)
168 					break;
169 				if (signal_pending(current))
170 					break;
171 				udelay(5);
172 			}
173 
174 			/* Poll slowly. */
175 			while (!(inb(ECONTROL(p)) & 0x01)) {
176 				if (time_after_eq(jiffies, expire))
177 					/* The FIFO is stuck. */
178 					return -EBUSY;
179 				schedule_timeout_interruptible(
180 							msecs_to_jiffies(10));
181 				if (signal_pending(current))
182 					break;
183 			}
184 		}
185 	}
186 
187 	if (mode >= 2 && m >= 2) {
188 		/* We have to go through mode 001 */
189 		oecr &= ~(7 << 5);
190 		oecr |= ECR_PS2 << 5;
191 		ECR_WRITE(p, oecr);
192 	}
193 
194 	/* Set the mode. */
195 	oecr &= ~(7 << 5);
196 	oecr |= m << 5;
197 	ECR_WRITE(p, oecr);
198 	return 0;
199 }
200 #endif /* FIFO support */
201 
202 /*
203  * Clear TIMEOUT BIT in EPP MODE
204  *
205  * This is also used in SPP detection.
206  */
clear_epp_timeout(struct parport * pb)207 static int clear_epp_timeout(struct parport *pb)
208 {
209 	unsigned char r;
210 
211 	if (!(parport_pc_read_status(pb) & 0x01))
212 		return 1;
213 
214 	/* To clear timeout some chips require double read */
215 	parport_pc_read_status(pb);
216 	r = parport_pc_read_status(pb);
217 	outb(r | 0x01, STATUS(pb)); /* Some reset by writing 1 */
218 	outb(r & 0xfe, STATUS(pb)); /* Others by writing 0 */
219 	r = parport_pc_read_status(pb);
220 
221 	return !(r & 0x01);
222 }
223 
224 /*
225  * Access functions.
226  *
227  * Most of these aren't static because they may be used by the
228  * parport_xxx_yyy macros.  extern __inline__ versions of several
229  * of these are in parport_pc.h.
230  */
231 
parport_pc_init_state(struct pardevice * dev,struct parport_state * s)232 static void parport_pc_init_state(struct pardevice *dev,
233 						struct parport_state *s)
234 {
235 	s->u.pc.ctr = 0xc;
236 	if (dev->irq_func &&
237 	    dev->port->irq != PARPORT_IRQ_NONE)
238 		/* Set ackIntEn */
239 		s->u.pc.ctr |= 0x10;
240 
241 	s->u.pc.ecr = 0x34; /* NetMos chip can cause problems 0x24;
242 			     * D.Gruszka VScom */
243 }
244 
parport_pc_save_state(struct parport * p,struct parport_state * s)245 static void parport_pc_save_state(struct parport *p, struct parport_state *s)
246 {
247 	const struct parport_pc_private *priv = p->physport->private_data;
248 	s->u.pc.ctr = priv->ctr;
249 	if (priv->ecr)
250 		s->u.pc.ecr = inb(ECONTROL(p));
251 }
252 
parport_pc_restore_state(struct parport * p,struct parport_state * s)253 static void parport_pc_restore_state(struct parport *p,
254 						struct parport_state *s)
255 {
256 	struct parport_pc_private *priv = p->physport->private_data;
257 	register unsigned char c = s->u.pc.ctr & priv->ctr_writable;
258 	outb(c, CONTROL(p));
259 	priv->ctr = c;
260 	if (priv->ecr)
261 		ECR_WRITE(p, s->u.pc.ecr);
262 }
263 
264 #ifdef CONFIG_PARPORT_1284
parport_pc_epp_read_data(struct parport * port,void * buf,size_t length,int flags)265 static size_t parport_pc_epp_read_data(struct parport *port, void *buf,
266 				       size_t length, int flags)
267 {
268 	size_t got = 0;
269 
270 	if (flags & PARPORT_W91284PIC) {
271 		unsigned char status;
272 		size_t left = length;
273 
274 		/* use knowledge about data lines..:
275 		 *  nFault is 0 if there is at least 1 byte in the Warp's FIFO
276 		 *  pError is 1 if there are 16 bytes in the Warp's FIFO
277 		 */
278 		status = inb(STATUS(port));
279 
280 		while (!(status & 0x08) && got < length) {
281 			if (left >= 16 && (status & 0x20) && !(status & 0x08)) {
282 				/* can grab 16 bytes from warp fifo */
283 				if (!((long)buf & 0x03))
284 					insl(EPPDATA(port), buf, 4);
285 				else
286 					insb(EPPDATA(port), buf, 16);
287 				buf += 16;
288 				got += 16;
289 				left -= 16;
290 			} else {
291 				/* grab single byte from the warp fifo */
292 				*((char *)buf) = inb(EPPDATA(port));
293 				buf++;
294 				got++;
295 				left--;
296 			}
297 			status = inb(STATUS(port));
298 			if (status & 0x01) {
299 				/* EPP timeout should never occur... */
300 				printk(KERN_DEBUG
301 "%s: EPP timeout occurred while talking to w91284pic (should not have done)\n", port->name);
302 				clear_epp_timeout(port);
303 			}
304 		}
305 		return got;
306 	}
307 	if ((flags & PARPORT_EPP_FAST) && (length > 1)) {
308 		if (!(((long)buf | length) & 0x03))
309 			insl(EPPDATA(port), buf, (length >> 2));
310 		else
311 			insb(EPPDATA(port), buf, length);
312 		if (inb(STATUS(port)) & 0x01) {
313 			clear_epp_timeout(port);
314 			return -EIO;
315 		}
316 		return length;
317 	}
318 	for (; got < length; got++) {
319 		*((char *)buf) = inb(EPPDATA(port));
320 		buf++;
321 		if (inb(STATUS(port)) & 0x01) {
322 			/* EPP timeout */
323 			clear_epp_timeout(port);
324 			break;
325 		}
326 	}
327 
328 	return got;
329 }
330 
parport_pc_epp_write_data(struct parport * port,const void * buf,size_t length,int flags)331 static size_t parport_pc_epp_write_data(struct parport *port, const void *buf,
332 					size_t length, int flags)
333 {
334 	size_t written = 0;
335 
336 	if ((flags & PARPORT_EPP_FAST) && (length > 1)) {
337 		if (!(((long)buf | length) & 0x03))
338 			outsl(EPPDATA(port), buf, (length >> 2));
339 		else
340 			outsb(EPPDATA(port), buf, length);
341 		if (inb(STATUS(port)) & 0x01) {
342 			clear_epp_timeout(port);
343 			return -EIO;
344 		}
345 		return length;
346 	}
347 	for (; written < length; written++) {
348 		outb(*((char *)buf), EPPDATA(port));
349 		buf++;
350 		if (inb(STATUS(port)) & 0x01) {
351 			clear_epp_timeout(port);
352 			break;
353 		}
354 	}
355 
356 	return written;
357 }
358 
parport_pc_epp_read_addr(struct parport * port,void * buf,size_t length,int flags)359 static size_t parport_pc_epp_read_addr(struct parport *port, void *buf,
360 					size_t length, int flags)
361 {
362 	size_t got = 0;
363 
364 	if ((flags & PARPORT_EPP_FAST) && (length > 1)) {
365 		insb(EPPADDR(port), buf, length);
366 		if (inb(STATUS(port)) & 0x01) {
367 			clear_epp_timeout(port);
368 			return -EIO;
369 		}
370 		return length;
371 	}
372 	for (; got < length; got++) {
373 		*((char *)buf) = inb(EPPADDR(port));
374 		buf++;
375 		if (inb(STATUS(port)) & 0x01) {
376 			clear_epp_timeout(port);
377 			break;
378 		}
379 	}
380 
381 	return got;
382 }
383 
parport_pc_epp_write_addr(struct parport * port,const void * buf,size_t length,int flags)384 static size_t parport_pc_epp_write_addr(struct parport *port,
385 					 const void *buf, size_t length,
386 					 int flags)
387 {
388 	size_t written = 0;
389 
390 	if ((flags & PARPORT_EPP_FAST) && (length > 1)) {
391 		outsb(EPPADDR(port), buf, length);
392 		if (inb(STATUS(port)) & 0x01) {
393 			clear_epp_timeout(port);
394 			return -EIO;
395 		}
396 		return length;
397 	}
398 	for (; written < length; written++) {
399 		outb(*((char *)buf), EPPADDR(port));
400 		buf++;
401 		if (inb(STATUS(port)) & 0x01) {
402 			clear_epp_timeout(port);
403 			break;
404 		}
405 	}
406 
407 	return written;
408 }
409 
parport_pc_ecpepp_read_data(struct parport * port,void * buf,size_t length,int flags)410 static size_t parport_pc_ecpepp_read_data(struct parport *port, void *buf,
411 					  size_t length, int flags)
412 {
413 	size_t got;
414 
415 	frob_set_mode(port, ECR_EPP);
416 	parport_pc_data_reverse(port);
417 	parport_pc_write_control(port, 0x4);
418 	got = parport_pc_epp_read_data(port, buf, length, flags);
419 	frob_set_mode(port, ECR_PS2);
420 
421 	return got;
422 }
423 
parport_pc_ecpepp_write_data(struct parport * port,const void * buf,size_t length,int flags)424 static size_t parport_pc_ecpepp_write_data(struct parport *port,
425 					   const void *buf, size_t length,
426 					   int flags)
427 {
428 	size_t written;
429 
430 	frob_set_mode(port, ECR_EPP);
431 	parport_pc_write_control(port, 0x4);
432 	parport_pc_data_forward(port);
433 	written = parport_pc_epp_write_data(port, buf, length, flags);
434 	frob_set_mode(port, ECR_PS2);
435 
436 	return written;
437 }
438 
parport_pc_ecpepp_read_addr(struct parport * port,void * buf,size_t length,int flags)439 static size_t parport_pc_ecpepp_read_addr(struct parport *port, void *buf,
440 					  size_t length, int flags)
441 {
442 	size_t got;
443 
444 	frob_set_mode(port, ECR_EPP);
445 	parport_pc_data_reverse(port);
446 	parport_pc_write_control(port, 0x4);
447 	got = parport_pc_epp_read_addr(port, buf, length, flags);
448 	frob_set_mode(port, ECR_PS2);
449 
450 	return got;
451 }
452 
parport_pc_ecpepp_write_addr(struct parport * port,const void * buf,size_t length,int flags)453 static size_t parport_pc_ecpepp_write_addr(struct parport *port,
454 					    const void *buf, size_t length,
455 					    int flags)
456 {
457 	size_t written;
458 
459 	frob_set_mode(port, ECR_EPP);
460 	parport_pc_write_control(port, 0x4);
461 	parport_pc_data_forward(port);
462 	written = parport_pc_epp_write_addr(port, buf, length, flags);
463 	frob_set_mode(port, ECR_PS2);
464 
465 	return written;
466 }
467 #endif /* IEEE 1284 support */
468 
469 #ifdef CONFIG_PARPORT_PC_FIFO
parport_pc_fifo_write_block_pio(struct parport * port,const void * buf,size_t length)470 static size_t parport_pc_fifo_write_block_pio(struct parport *port,
471 					       const void *buf, size_t length)
472 {
473 	int ret = 0;
474 	const unsigned char *bufp = buf;
475 	size_t left = length;
476 	unsigned long expire = jiffies + port->physport->cad->timeout;
477 	const unsigned long fifo = FIFO(port);
478 	int poll_for = 8; /* 80 usecs */
479 	const struct parport_pc_private *priv = port->physport->private_data;
480 	const int fifo_depth = priv->fifo_depth;
481 
482 	port = port->physport;
483 
484 	/* We don't want to be interrupted every character. */
485 	parport_pc_disable_irq(port);
486 	/* set nErrIntrEn and serviceIntr */
487 	frob_econtrol(port, (1<<4) | (1<<2), (1<<4) | (1<<2));
488 
489 	/* Forward mode. */
490 	parport_pc_data_forward(port); /* Must be in PS2 mode */
491 
492 	while (left) {
493 		unsigned char byte;
494 		unsigned char ecrval = inb(ECONTROL(port));
495 		int i = 0;
496 
497 		if (need_resched() && time_before(jiffies, expire))
498 			/* Can't yield the port. */
499 			schedule();
500 
501 		/* Anyone else waiting for the port? */
502 		if (port->waithead) {
503 			printk(KERN_DEBUG "Somebody wants the port\n");
504 			break;
505 		}
506 
507 		if (ecrval & 0x02) {
508 			/* FIFO is full. Wait for interrupt. */
509 
510 			/* Clear serviceIntr */
511 			ECR_WRITE(port, ecrval & ~(1<<2));
512 false_alarm:
513 			ret = parport_wait_event(port, HZ);
514 			if (ret < 0)
515 				break;
516 			ret = 0;
517 			if (!time_before(jiffies, expire)) {
518 				/* Timed out. */
519 				printk(KERN_DEBUG "FIFO write timed out\n");
520 				break;
521 			}
522 			ecrval = inb(ECONTROL(port));
523 			if (!(ecrval & (1<<2))) {
524 				if (need_resched() &&
525 				    time_before(jiffies, expire))
526 					schedule();
527 
528 				goto false_alarm;
529 			}
530 
531 			continue;
532 		}
533 
534 		/* Can't fail now. */
535 		expire = jiffies + port->cad->timeout;
536 
537 poll:
538 		if (signal_pending(current))
539 			break;
540 
541 		if (ecrval & 0x01) {
542 			/* FIFO is empty. Blast it full. */
543 			const int n = left < fifo_depth ? left : fifo_depth;
544 			outsb(fifo, bufp, n);
545 			bufp += n;
546 			left -= n;
547 
548 			/* Adjust the poll time. */
549 			if (i < (poll_for - 2))
550 				poll_for--;
551 			continue;
552 		} else if (i++ < poll_for) {
553 			udelay(10);
554 			ecrval = inb(ECONTROL(port));
555 			goto poll;
556 		}
557 
558 		/* Half-full(call me an optimist) */
559 		byte = *bufp++;
560 		outb(byte, fifo);
561 		left--;
562 	}
563 	dump_parport_state("leave fifo_write_block_pio", port);
564 	return length - left;
565 }
566 
567 #ifdef HAS_DMA
parport_pc_fifo_write_block_dma(struct parport * port,const void * buf,size_t length)568 static size_t parport_pc_fifo_write_block_dma(struct parport *port,
569 					       const void *buf, size_t length)
570 {
571 	int ret = 0;
572 	unsigned long dmaflag;
573 	size_t left = length;
574 	const struct parport_pc_private *priv = port->physport->private_data;
575 	struct device *dev = port->physport->dev;
576 	dma_addr_t dma_addr, dma_handle;
577 	size_t maxlen = 0x10000; /* max 64k per DMA transfer */
578 	unsigned long start = (unsigned long) buf;
579 	unsigned long end = (unsigned long) buf + length - 1;
580 
581 	dump_parport_state("enter fifo_write_block_dma", port);
582 	if (end < MAX_DMA_ADDRESS) {
583 		/* If it would cross a 64k boundary, cap it at the end. */
584 		if ((start ^ end) & ~0xffffUL)
585 			maxlen = 0x10000 - (start & 0xffff);
586 
587 		dma_addr = dma_handle = dma_map_single(dev, (void *)buf, length,
588 						       DMA_TO_DEVICE);
589 	} else {
590 		/* above 16 MB we use a bounce buffer as ISA-DMA
591 		   is not possible */
592 		maxlen   = PAGE_SIZE;          /* sizeof(priv->dma_buf) */
593 		dma_addr = priv->dma_handle;
594 		dma_handle = 0;
595 	}
596 
597 	port = port->physport;
598 
599 	/* We don't want to be interrupted every character. */
600 	parport_pc_disable_irq(port);
601 	/* set nErrIntrEn and serviceIntr */
602 	frob_econtrol(port, (1<<4) | (1<<2), (1<<4) | (1<<2));
603 
604 	/* Forward mode. */
605 	parport_pc_data_forward(port); /* Must be in PS2 mode */
606 
607 	while (left) {
608 		unsigned long expire = jiffies + port->physport->cad->timeout;
609 
610 		size_t count = left;
611 
612 		if (count > maxlen)
613 			count = maxlen;
614 
615 		if (!dma_handle)   /* bounce buffer ! */
616 			memcpy(priv->dma_buf, buf, count);
617 
618 		dmaflag = claim_dma_lock();
619 		disable_dma(port->dma);
620 		clear_dma_ff(port->dma);
621 		set_dma_mode(port->dma, DMA_MODE_WRITE);
622 		set_dma_addr(port->dma, dma_addr);
623 		set_dma_count(port->dma, count);
624 
625 		/* Set DMA mode */
626 		frob_econtrol(port, 1<<3, 1<<3);
627 
628 		/* Clear serviceIntr */
629 		frob_econtrol(port, 1<<2, 0);
630 
631 		enable_dma(port->dma);
632 		release_dma_lock(dmaflag);
633 
634 		/* assume DMA will be successful */
635 		left -= count;
636 		buf  += count;
637 		if (dma_handle)
638 			dma_addr += count;
639 
640 		/* Wait for interrupt. */
641 false_alarm:
642 		ret = parport_wait_event(port, HZ);
643 		if (ret < 0)
644 			break;
645 		ret = 0;
646 		if (!time_before(jiffies, expire)) {
647 			/* Timed out. */
648 			printk(KERN_DEBUG "DMA write timed out\n");
649 			break;
650 		}
651 		/* Is serviceIntr set? */
652 		if (!(inb(ECONTROL(port)) & (1<<2))) {
653 			cond_resched();
654 
655 			goto false_alarm;
656 		}
657 
658 		dmaflag = claim_dma_lock();
659 		disable_dma(port->dma);
660 		clear_dma_ff(port->dma);
661 		count = get_dma_residue(port->dma);
662 		release_dma_lock(dmaflag);
663 
664 		cond_resched(); /* Can't yield the port. */
665 
666 		/* Anyone else waiting for the port? */
667 		if (port->waithead) {
668 			printk(KERN_DEBUG "Somebody wants the port\n");
669 			break;
670 		}
671 
672 		/* update for possible DMA residue ! */
673 		buf  -= count;
674 		left += count;
675 		if (dma_handle)
676 			dma_addr -= count;
677 	}
678 
679 	/* Maybe got here through break, so adjust for DMA residue! */
680 	dmaflag = claim_dma_lock();
681 	disable_dma(port->dma);
682 	clear_dma_ff(port->dma);
683 	left += get_dma_residue(port->dma);
684 	release_dma_lock(dmaflag);
685 
686 	/* Turn off DMA mode */
687 	frob_econtrol(port, 1<<3, 0);
688 
689 	if (dma_handle)
690 		dma_unmap_single(dev, dma_handle, length, DMA_TO_DEVICE);
691 
692 	dump_parport_state("leave fifo_write_block_dma", port);
693 	return length - left;
694 }
695 #endif
696 
parport_pc_fifo_write_block(struct parport * port,const void * buf,size_t length)697 static inline size_t parport_pc_fifo_write_block(struct parport *port,
698 					       const void *buf, size_t length)
699 {
700 #ifdef HAS_DMA
701 	if (port->dma != PARPORT_DMA_NONE)
702 		return parport_pc_fifo_write_block_dma(port, buf, length);
703 #endif
704 	return parport_pc_fifo_write_block_pio(port, buf, length);
705 }
706 
707 /* Parallel Port FIFO mode (ECP chipsets) */
parport_pc_compat_write_block_pio(struct parport * port,const void * buf,size_t length,int flags)708 static size_t parport_pc_compat_write_block_pio(struct parport *port,
709 						 const void *buf, size_t length,
710 						 int flags)
711 {
712 	size_t written;
713 	int r;
714 	unsigned long expire;
715 	const struct parport_pc_private *priv = port->physport->private_data;
716 
717 	/* Special case: a timeout of zero means we cannot call schedule().
718 	 * Also if O_NONBLOCK is set then use the default implementation. */
719 	if (port->physport->cad->timeout <= PARPORT_INACTIVITY_O_NONBLOCK)
720 		return parport_ieee1284_write_compat(port, buf,
721 						      length, flags);
722 
723 	/* Set up parallel port FIFO mode.*/
724 	parport_pc_data_forward(port); /* Must be in PS2 mode */
725 	parport_pc_frob_control(port, PARPORT_CONTROL_STROBE, 0);
726 	r = change_mode(port, ECR_PPF); /* Parallel port FIFO */
727 	if (r)
728 		printk(KERN_DEBUG "%s: Warning change_mode ECR_PPF failed\n",
729 								port->name);
730 
731 	port->physport->ieee1284.phase = IEEE1284_PH_FWD_DATA;
732 
733 	/* Write the data to the FIFO. */
734 	written = parport_pc_fifo_write_block(port, buf, length);
735 
736 	/* Finish up. */
737 	/* For some hardware we don't want to touch the mode until
738 	 * the FIFO is empty, so allow 4 seconds for each position
739 	 * in the fifo.
740 	 */
741 	expire = jiffies + (priv->fifo_depth * HZ * 4);
742 	do {
743 		/* Wait for the FIFO to empty */
744 		r = change_mode(port, ECR_PS2);
745 		if (r != -EBUSY)
746 			break;
747 	} while (time_before(jiffies, expire));
748 	if (r == -EBUSY) {
749 
750 		printk(KERN_DEBUG "%s: FIFO is stuck\n", port->name);
751 
752 		/* Prevent further data transfer. */
753 		frob_set_mode(port, ECR_TST);
754 
755 		/* Adjust for the contents of the FIFO. */
756 		for (written -= priv->fifo_depth; ; written++) {
757 			if (inb(ECONTROL(port)) & 0x2) {
758 				/* Full up. */
759 				break;
760 			}
761 			outb(0, FIFO(port));
762 		}
763 
764 		/* Reset the FIFO and return to PS2 mode. */
765 		frob_set_mode(port, ECR_PS2);
766 	}
767 
768 	r = parport_wait_peripheral(port,
769 				     PARPORT_STATUS_BUSY,
770 				     PARPORT_STATUS_BUSY);
771 	if (r)
772 		printk(KERN_DEBUG
773 			"%s: BUSY timeout (%d) in compat_write_block_pio\n",
774 			port->name, r);
775 
776 	port->physport->ieee1284.phase = IEEE1284_PH_FWD_IDLE;
777 
778 	return written;
779 }
780 
781 /* ECP */
782 #ifdef CONFIG_PARPORT_1284
parport_pc_ecp_write_block_pio(struct parport * port,const void * buf,size_t length,int flags)783 static size_t parport_pc_ecp_write_block_pio(struct parport *port,
784 					      const void *buf, size_t length,
785 					      int flags)
786 {
787 	size_t written;
788 	int r;
789 	unsigned long expire;
790 	const struct parport_pc_private *priv = port->physport->private_data;
791 
792 	/* Special case: a timeout of zero means we cannot call schedule().
793 	 * Also if O_NONBLOCK is set then use the default implementation. */
794 	if (port->physport->cad->timeout <= PARPORT_INACTIVITY_O_NONBLOCK)
795 		return parport_ieee1284_ecp_write_data(port, buf,
796 							length, flags);
797 
798 	/* Switch to forward mode if necessary. */
799 	if (port->physport->ieee1284.phase != IEEE1284_PH_FWD_IDLE) {
800 		/* Event 47: Set nInit high. */
801 		parport_frob_control(port,
802 				      PARPORT_CONTROL_INIT
803 				      | PARPORT_CONTROL_AUTOFD,
804 				      PARPORT_CONTROL_INIT
805 				      | PARPORT_CONTROL_AUTOFD);
806 
807 		/* Event 49: PError goes high. */
808 		r = parport_wait_peripheral(port,
809 					     PARPORT_STATUS_PAPEROUT,
810 					     PARPORT_STATUS_PAPEROUT);
811 		if (r) {
812 			printk(KERN_DEBUG "%s: PError timeout (%d) "
813 				"in ecp_write_block_pio\n", port->name, r);
814 		}
815 	}
816 
817 	/* Set up ECP parallel port mode.*/
818 	parport_pc_data_forward(port); /* Must be in PS2 mode */
819 	parport_pc_frob_control(port,
820 				 PARPORT_CONTROL_STROBE |
821 				 PARPORT_CONTROL_AUTOFD,
822 				 0);
823 	r = change_mode(port, ECR_ECP); /* ECP FIFO */
824 	if (r)
825 		printk(KERN_DEBUG "%s: Warning change_mode ECR_ECP failed\n",
826 								port->name);
827 	port->physport->ieee1284.phase = IEEE1284_PH_FWD_DATA;
828 
829 	/* Write the data to the FIFO. */
830 	written = parport_pc_fifo_write_block(port, buf, length);
831 
832 	/* Finish up. */
833 	/* For some hardware we don't want to touch the mode until
834 	 * the FIFO is empty, so allow 4 seconds for each position
835 	 * in the fifo.
836 	 */
837 	expire = jiffies + (priv->fifo_depth * (HZ * 4));
838 	do {
839 		/* Wait for the FIFO to empty */
840 		r = change_mode(port, ECR_PS2);
841 		if (r != -EBUSY)
842 			break;
843 	} while (time_before(jiffies, expire));
844 	if (r == -EBUSY) {
845 
846 		printk(KERN_DEBUG "%s: FIFO is stuck\n", port->name);
847 
848 		/* Prevent further data transfer. */
849 		frob_set_mode(port, ECR_TST);
850 
851 		/* Adjust for the contents of the FIFO. */
852 		for (written -= priv->fifo_depth; ; written++) {
853 			if (inb(ECONTROL(port)) & 0x2) {
854 				/* Full up. */
855 				break;
856 			}
857 			outb(0, FIFO(port));
858 		}
859 
860 		/* Reset the FIFO and return to PS2 mode. */
861 		frob_set_mode(port, ECR_PS2);
862 
863 		/* Host transfer recovery. */
864 		parport_pc_data_reverse(port); /* Must be in PS2 mode */
865 		udelay(5);
866 		parport_frob_control(port, PARPORT_CONTROL_INIT, 0);
867 		r = parport_wait_peripheral(port, PARPORT_STATUS_PAPEROUT, 0);
868 		if (r)
869 			printk(KERN_DEBUG "%s: PE,1 timeout (%d) "
870 				"in ecp_write_block_pio\n", port->name, r);
871 
872 		parport_frob_control(port,
873 				      PARPORT_CONTROL_INIT,
874 				      PARPORT_CONTROL_INIT);
875 		r = parport_wait_peripheral(port,
876 					     PARPORT_STATUS_PAPEROUT,
877 					     PARPORT_STATUS_PAPEROUT);
878 		if (r)
879 			printk(KERN_DEBUG "%s: PE,2 timeout (%d) "
880 				"in ecp_write_block_pio\n", port->name, r);
881 	}
882 
883 	r = parport_wait_peripheral(port,
884 				     PARPORT_STATUS_BUSY,
885 				     PARPORT_STATUS_BUSY);
886 	if (r)
887 		printk(KERN_DEBUG
888 			"%s: BUSY timeout (%d) in ecp_write_block_pio\n",
889 			port->name, r);
890 
891 	port->physport->ieee1284.phase = IEEE1284_PH_FWD_IDLE;
892 
893 	return written;
894 }
895 #endif /* IEEE 1284 support */
896 #endif /* Allowed to use FIFO/DMA */
897 
898 
899 /*
900  *	******************************************
901  *	INITIALISATION AND MODULE STUFF BELOW HERE
902  *	******************************************
903  */
904 
905 /* GCC is not inlining extern inline function later overwritten to non-inline,
906    so we use outlined_ variants here.  */
907 static const struct parport_operations parport_pc_ops = {
908 	.write_data	= parport_pc_write_data,
909 	.read_data	= parport_pc_read_data,
910 
911 	.write_control	= parport_pc_write_control,
912 	.read_control	= parport_pc_read_control,
913 	.frob_control	= parport_pc_frob_control,
914 
915 	.read_status	= parport_pc_read_status,
916 
917 	.enable_irq	= parport_pc_enable_irq,
918 	.disable_irq	= parport_pc_disable_irq,
919 
920 	.data_forward	= parport_pc_data_forward,
921 	.data_reverse	= parport_pc_data_reverse,
922 
923 	.init_state	= parport_pc_init_state,
924 	.save_state	= parport_pc_save_state,
925 	.restore_state	= parport_pc_restore_state,
926 
927 	.epp_write_data	= parport_ieee1284_epp_write_data,
928 	.epp_read_data	= parport_ieee1284_epp_read_data,
929 	.epp_write_addr	= parport_ieee1284_epp_write_addr,
930 	.epp_read_addr	= parport_ieee1284_epp_read_addr,
931 
932 	.ecp_write_data	= parport_ieee1284_ecp_write_data,
933 	.ecp_read_data	= parport_ieee1284_ecp_read_data,
934 	.ecp_write_addr	= parport_ieee1284_ecp_write_addr,
935 
936 	.compat_write_data	= parport_ieee1284_write_compat,
937 	.nibble_read_data	= parport_ieee1284_read_nibble,
938 	.byte_read_data		= parport_ieee1284_read_byte,
939 
940 	.owner		= THIS_MODULE,
941 };
942 
943 #ifdef CONFIG_PARPORT_PC_SUPERIO
944 
find_free_superio(void)945 static struct superio_struct *find_free_superio(void)
946 {
947 	int i;
948 	for (i = 0; i < NR_SUPERIOS; i++)
949 		if (superios[i].io == 0)
950 			return &superios[i];
951 	return NULL;
952 }
953 
954 
955 /* Super-IO chipset detection, Winbond, SMSC */
show_parconfig_smsc37c669(int io,int key)956 static void show_parconfig_smsc37c669(int io, int key)
957 {
958 	int cr1, cr4, cra, cr23, cr26, cr27;
959 	struct superio_struct *s;
960 
961 	static const char *const modes[] = {
962 		"SPP and Bidirectional (PS/2)",
963 		"EPP and SPP",
964 		"ECP",
965 		"ECP and EPP" };
966 
967 	outb(key, io);
968 	outb(key, io);
969 	outb(1, io);
970 	cr1 = inb(io + 1);
971 	outb(4, io);
972 	cr4 = inb(io + 1);
973 	outb(0x0a, io);
974 	cra = inb(io + 1);
975 	outb(0x23, io);
976 	cr23 = inb(io + 1);
977 	outb(0x26, io);
978 	cr26 = inb(io + 1);
979 	outb(0x27, io);
980 	cr27 = inb(io + 1);
981 	outb(0xaa, io);
982 
983 	if (verbose_probing) {
984 		printk(KERN_INFO
985 			"SMSC 37c669 LPT Config: cr_1=0x%02x, 4=0x%02x, "
986 			"A=0x%2x, 23=0x%02x, 26=0x%02x, 27=0x%02x\n",
987 			cr1, cr4, cra, cr23, cr26, cr27);
988 
989 		/* The documentation calls DMA and IRQ-Lines by letters, so
990 		   the board maker can/will wire them
991 		   appropriately/randomly...  G=reserved H=IDE-irq, */
992 		printk(KERN_INFO
993 	"SMSC LPT Config: io=0x%04x, irq=%c, dma=%c, fifo threshold=%d\n",
994 				cr23 * 4,
995 				(cr27 & 0x0f) ? 'A' - 1 + (cr27 & 0x0f) : '-',
996 				(cr26 & 0x0f) ? 'A' - 1 + (cr26 & 0x0f) : '-',
997 				cra & 0x0f);
998 		printk(KERN_INFO "SMSC LPT Config: enabled=%s power=%s\n",
999 		       (cr23 * 4 >= 0x100) ? "yes" : "no",
1000 		       (cr1 & 4) ? "yes" : "no");
1001 		printk(KERN_INFO
1002 			"SMSC LPT Config: Port mode=%s, EPP version =%s\n",
1003 				(cr1 & 0x08) ? "Standard mode only (SPP)"
1004 					      : modes[cr4 & 0x03],
1005 				(cr4 & 0x40) ? "1.7" : "1.9");
1006 	}
1007 
1008 	/* Heuristics !  BIOS setup for this mainboard device limits
1009 	   the choices to standard settings, i.e. io-address and IRQ
1010 	   are related, however DMA can be 1 or 3, assume DMA_A=DMA1,
1011 	   DMA_C=DMA3 (this is true e.g. for TYAN 1564D Tomcat IV) */
1012 	if (cr23 * 4 >= 0x100) { /* if active */
1013 		s = find_free_superio();
1014 		if (s == NULL)
1015 			printk(KERN_INFO "Super-IO: too many chips!\n");
1016 		else {
1017 			int d;
1018 			switch (cr23 * 4) {
1019 			case 0x3bc:
1020 				s->io = 0x3bc;
1021 				s->irq = 7;
1022 				break;
1023 			case 0x378:
1024 				s->io = 0x378;
1025 				s->irq = 7;
1026 				break;
1027 			case 0x278:
1028 				s->io = 0x278;
1029 				s->irq = 5;
1030 			}
1031 			d = (cr26 & 0x0f);
1032 			if (d == 1 || d == 3)
1033 				s->dma = d;
1034 			else
1035 				s->dma = PARPORT_DMA_NONE;
1036 		}
1037 	}
1038 }
1039 
1040 
show_parconfig_winbond(int io,int key)1041 static void show_parconfig_winbond(int io, int key)
1042 {
1043 	int cr30, cr60, cr61, cr70, cr74, crf0;
1044 	struct superio_struct *s;
1045 	static const char *const modes[] = {
1046 		"Standard (SPP) and Bidirectional(PS/2)", /* 0 */
1047 		"EPP-1.9 and SPP",
1048 		"ECP",
1049 		"ECP and EPP-1.9",
1050 		"Standard (SPP)",
1051 		"EPP-1.7 and SPP",		/* 5 */
1052 		"undefined!",
1053 		"ECP and EPP-1.7" };
1054 	static char *const irqtypes[] = {
1055 		"pulsed low, high-Z",
1056 		"follows nACK" };
1057 
1058 	/* The registers are called compatible-PnP because the
1059 	   register layout is modelled after ISA-PnP, the access
1060 	   method is just another ... */
1061 	outb(key, io);
1062 	outb(key, io);
1063 	outb(0x07, io);   /* Register 7: Select Logical Device */
1064 	outb(0x01, io + 1); /* LD1 is Parallel Port */
1065 	outb(0x30, io);
1066 	cr30 = inb(io + 1);
1067 	outb(0x60, io);
1068 	cr60 = inb(io + 1);
1069 	outb(0x61, io);
1070 	cr61 = inb(io + 1);
1071 	outb(0x70, io);
1072 	cr70 = inb(io + 1);
1073 	outb(0x74, io);
1074 	cr74 = inb(io + 1);
1075 	outb(0xf0, io);
1076 	crf0 = inb(io + 1);
1077 	outb(0xaa, io);
1078 
1079 	if (verbose_probing) {
1080 		printk(KERN_INFO
1081     "Winbond LPT Config: cr_30=%02x 60,61=%02x%02x 70=%02x 74=%02x, f0=%02x\n",
1082 					cr30, cr60, cr61, cr70, cr74, crf0);
1083 		printk(KERN_INFO "Winbond LPT Config: active=%s, io=0x%02x%02x irq=%d, ",
1084 		       (cr30 & 0x01) ? "yes" : "no", cr60, cr61, cr70 & 0x0f);
1085 		if ((cr74 & 0x07) > 3)
1086 			pr_cont("dma=none\n");
1087 		else
1088 			pr_cont("dma=%d\n", cr74 & 0x07);
1089 		printk(KERN_INFO
1090 		    "Winbond LPT Config: irqtype=%s, ECP fifo threshold=%d\n",
1091 					irqtypes[crf0>>7], (crf0>>3)&0x0f);
1092 		printk(KERN_INFO "Winbond LPT Config: Port mode=%s\n",
1093 					modes[crf0 & 0x07]);
1094 	}
1095 
1096 	if (cr30 & 0x01) { /* the settings can be interrogated later ... */
1097 		s = find_free_superio();
1098 		if (s == NULL)
1099 			printk(KERN_INFO "Super-IO: too many chips!\n");
1100 		else {
1101 			s->io = (cr60 << 8) | cr61;
1102 			s->irq = cr70 & 0x0f;
1103 			s->dma = (((cr74 & 0x07) > 3) ?
1104 					   PARPORT_DMA_NONE : (cr74 & 0x07));
1105 		}
1106 	}
1107 }
1108 
decode_winbond(int efer,int key,int devid,int devrev,int oldid)1109 static void decode_winbond(int efer, int key, int devid, int devrev, int oldid)
1110 {
1111 	const char *type = "unknown";
1112 	int id, progif = 2;
1113 
1114 	if (devid == devrev)
1115 		/* simple heuristics, we happened to read some
1116 		   non-winbond register */
1117 		return;
1118 
1119 	id = (devid << 8) | devrev;
1120 
1121 	/* Values are from public data sheets pdf files, I can just
1122 	   confirm 83977TF is correct :-) */
1123 	if (id == 0x9771)
1124 		type = "83977F/AF";
1125 	else if (id == 0x9773)
1126 		type = "83977TF / SMSC 97w33x/97w34x";
1127 	else if (id == 0x9774)
1128 		type = "83977ATF";
1129 	else if ((id & ~0x0f) == 0x5270)
1130 		type = "83977CTF / SMSC 97w36x";
1131 	else if ((id & ~0x0f) == 0x52f0)
1132 		type = "83977EF / SMSC 97w35x";
1133 	else if ((id & ~0x0f) == 0x5210)
1134 		type = "83627";
1135 	else if ((id & ~0x0f) == 0x6010)
1136 		type = "83697HF";
1137 	else if ((oldid & 0x0f) == 0x0a) {
1138 		type = "83877F";
1139 		progif = 1;
1140 	} else if ((oldid & 0x0f) == 0x0b) {
1141 		type = "83877AF";
1142 		progif = 1;
1143 	} else if ((oldid & 0x0f) == 0x0c) {
1144 		type = "83877TF";
1145 		progif = 1;
1146 	} else if ((oldid & 0x0f) == 0x0d) {
1147 		type = "83877ATF";
1148 		progif = 1;
1149 	} else
1150 		progif = 0;
1151 
1152 	if (verbose_probing)
1153 		printk(KERN_INFO "Winbond chip at EFER=0x%x key=0x%02x "
1154 		       "devid=%02x devrev=%02x oldid=%02x type=%s\n",
1155 		       efer, key, devid, devrev, oldid, type);
1156 
1157 	if (progif == 2)
1158 		show_parconfig_winbond(efer, key);
1159 }
1160 
decode_smsc(int efer,int key,int devid,int devrev)1161 static void decode_smsc(int efer, int key, int devid, int devrev)
1162 {
1163 	const char *type = "unknown";
1164 	void (*func)(int io, int key);
1165 	int id;
1166 
1167 	if (devid == devrev)
1168 		/* simple heuristics, we happened to read some
1169 		   non-smsc register */
1170 		return;
1171 
1172 	func = NULL;
1173 	id = (devid << 8) | devrev;
1174 
1175 	if (id == 0x0302) {
1176 		type = "37c669";
1177 		func = show_parconfig_smsc37c669;
1178 	} else if (id == 0x6582)
1179 		type = "37c665IR";
1180 	else if	(devid == 0x65)
1181 		type = "37c665GT";
1182 	else if	(devid == 0x66)
1183 		type = "37c666GT";
1184 
1185 	if (verbose_probing)
1186 		printk(KERN_INFO "SMSC chip at EFER=0x%x "
1187 		       "key=0x%02x devid=%02x devrev=%02x type=%s\n",
1188 		       efer, key, devid, devrev, type);
1189 
1190 	if (func)
1191 		func(efer, key);
1192 }
1193 
1194 
winbond_check(int io,int key)1195 static void winbond_check(int io, int key)
1196 {
1197 	int origval, devid, devrev, oldid, x_devid, x_devrev, x_oldid;
1198 
1199 	if (!request_region(io, 3, __func__))
1200 		return;
1201 
1202 	origval = inb(io); /* Save original value */
1203 
1204 	/* First probe without key */
1205 	outb(0x20, io);
1206 	x_devid = inb(io + 1);
1207 	outb(0x21, io);
1208 	x_devrev = inb(io + 1);
1209 	outb(0x09, io);
1210 	x_oldid = inb(io + 1);
1211 
1212 	outb(key, io);
1213 	outb(key, io);     /* Write Magic Sequence to EFER, extended
1214 			      function enable register */
1215 	outb(0x20, io);    /* Write EFIR, extended function index register */
1216 	devid = inb(io + 1);  /* Read EFDR, extended function data register */
1217 	outb(0x21, io);
1218 	devrev = inb(io + 1);
1219 	outb(0x09, io);
1220 	oldid = inb(io + 1);
1221 	outb(0xaa, io);    /* Magic Seal */
1222 
1223 	outb(origval, io); /* in case we poked some entirely different hardware */
1224 
1225 	if ((x_devid == devid) && (x_devrev == devrev) && (x_oldid == oldid))
1226 		goto out; /* protection against false positives */
1227 
1228 	decode_winbond(io, key, devid, devrev, oldid);
1229 out:
1230 	release_region(io, 3);
1231 }
1232 
winbond_check2(int io,int key)1233 static void winbond_check2(int io, int key)
1234 {
1235 	int origval[3], devid, devrev, oldid, x_devid, x_devrev, x_oldid;
1236 
1237 	if (!request_region(io, 3, __func__))
1238 		return;
1239 
1240 	origval[0] = inb(io); /* Save original values */
1241 	origval[1] = inb(io + 1);
1242 	origval[2] = inb(io + 2);
1243 
1244 	/* First probe without the key */
1245 	outb(0x20, io + 2);
1246 	x_devid = inb(io + 2);
1247 	outb(0x21, io + 1);
1248 	x_devrev = inb(io + 2);
1249 	outb(0x09, io + 1);
1250 	x_oldid = inb(io + 2);
1251 
1252 	outb(key, io);     /* Write Magic Byte to EFER, extended
1253 			      function enable register */
1254 	outb(0x20, io + 2);  /* Write EFIR, extended function index register */
1255 	devid = inb(io + 2);  /* Read EFDR, extended function data register */
1256 	outb(0x21, io + 1);
1257 	devrev = inb(io + 2);
1258 	outb(0x09, io + 1);
1259 	oldid = inb(io + 2);
1260 	outb(0xaa, io);    /* Magic Seal */
1261 
1262 	outb(origval[0], io); /* in case we poked some entirely different hardware */
1263 	outb(origval[1], io + 1);
1264 	outb(origval[2], io + 2);
1265 
1266 	if (x_devid == devid && x_devrev == devrev && x_oldid == oldid)
1267 		goto out; /* protection against false positives */
1268 
1269 	decode_winbond(io, key, devid, devrev, oldid);
1270 out:
1271 	release_region(io, 3);
1272 }
1273 
smsc_check(int io,int key)1274 static void smsc_check(int io, int key)
1275 {
1276 	int origval, id, rev, oldid, oldrev, x_id, x_rev, x_oldid, x_oldrev;
1277 
1278 	if (!request_region(io, 3, __func__))
1279 		return;
1280 
1281 	origval = inb(io); /* Save original value */
1282 
1283 	/* First probe without the key */
1284 	outb(0x0d, io);
1285 	x_oldid = inb(io + 1);
1286 	outb(0x0e, io);
1287 	x_oldrev = inb(io + 1);
1288 	outb(0x20, io);
1289 	x_id = inb(io + 1);
1290 	outb(0x21, io);
1291 	x_rev = inb(io + 1);
1292 
1293 	outb(key, io);
1294 	outb(key, io);     /* Write Magic Sequence to EFER, extended
1295 			      function enable register */
1296 	outb(0x0d, io);    /* Write EFIR, extended function index register */
1297 	oldid = inb(io + 1);  /* Read EFDR, extended function data register */
1298 	outb(0x0e, io);
1299 	oldrev = inb(io + 1);
1300 	outb(0x20, io);
1301 	id = inb(io + 1);
1302 	outb(0x21, io);
1303 	rev = inb(io + 1);
1304 	outb(0xaa, io);    /* Magic Seal */
1305 
1306 	outb(origval, io); /* in case we poked some entirely different hardware */
1307 
1308 	if (x_id == id && x_oldrev == oldrev &&
1309 	    x_oldid == oldid && x_rev == rev)
1310 		goto out; /* protection against false positives */
1311 
1312 	decode_smsc(io, key, oldid, oldrev);
1313 out:
1314 	release_region(io, 3);
1315 }
1316 
1317 
detect_and_report_winbond(void)1318 static void detect_and_report_winbond(void)
1319 {
1320 	if (verbose_probing)
1321 		printk(KERN_DEBUG "Winbond Super-IO detection, now testing ports 3F0,370,250,4E,2E ...\n");
1322 	winbond_check(0x3f0, 0x87);
1323 	winbond_check(0x370, 0x87);
1324 	winbond_check(0x2e , 0x87);
1325 	winbond_check(0x4e , 0x87);
1326 	winbond_check(0x3f0, 0x86);
1327 	winbond_check2(0x250, 0x88);
1328 	winbond_check2(0x250, 0x89);
1329 }
1330 
detect_and_report_smsc(void)1331 static void detect_and_report_smsc(void)
1332 {
1333 	if (verbose_probing)
1334 		printk(KERN_DEBUG "SMSC Super-IO detection, now testing Ports 2F0, 370 ...\n");
1335 	smsc_check(0x3f0, 0x55);
1336 	smsc_check(0x370, 0x55);
1337 	smsc_check(0x3f0, 0x44);
1338 	smsc_check(0x370, 0x44);
1339 }
1340 
detect_and_report_it87(void)1341 static void detect_and_report_it87(void)
1342 {
1343 	u16 dev;
1344 	u8 origval, r;
1345 	if (verbose_probing)
1346 		printk(KERN_DEBUG "IT8705 Super-IO detection, now testing port 2E ...\n");
1347 	if (!request_muxed_region(0x2e, 2, __func__))
1348 		return;
1349 	origval = inb(0x2e);		/* Save original value */
1350 	outb(0x87, 0x2e);
1351 	outb(0x01, 0x2e);
1352 	outb(0x55, 0x2e);
1353 	outb(0x55, 0x2e);
1354 	outb(0x20, 0x2e);
1355 	dev = inb(0x2f) << 8;
1356 	outb(0x21, 0x2e);
1357 	dev |= inb(0x2f);
1358 	if (dev == 0x8712 || dev == 0x8705 || dev == 0x8715 ||
1359 	    dev == 0x8716 || dev == 0x8718 || dev == 0x8726) {
1360 		printk(KERN_INFO "IT%04X SuperIO detected.\n", dev);
1361 		outb(0x07, 0x2E);	/* Parallel Port */
1362 		outb(0x03, 0x2F);
1363 		outb(0xF0, 0x2E);	/* BOOT 0x80 off */
1364 		r = inb(0x2f);
1365 		outb(0xF0, 0x2E);
1366 		outb(r | 8, 0x2F);
1367 		outb(0x02, 0x2E);	/* Lock */
1368 		outb(0x02, 0x2F);
1369 	} else {
1370 		outb(origval, 0x2e);	/* Oops, sorry to disturb */
1371 	}
1372 	release_region(0x2e, 2);
1373 }
1374 #endif /* CONFIG_PARPORT_PC_SUPERIO */
1375 
find_superio(struct parport * p)1376 static struct superio_struct *find_superio(struct parport *p)
1377 {
1378 	int i;
1379 	for (i = 0; i < NR_SUPERIOS; i++)
1380 		if (superios[i].io == p->base)
1381 			return &superios[i];
1382 	return NULL;
1383 }
1384 
get_superio_dma(struct parport * p)1385 static int get_superio_dma(struct parport *p)
1386 {
1387 	struct superio_struct *s = find_superio(p);
1388 	if (s)
1389 		return s->dma;
1390 	return PARPORT_DMA_NONE;
1391 }
1392 
get_superio_irq(struct parport * p)1393 static int get_superio_irq(struct parport *p)
1394 {
1395 	struct superio_struct *s = find_superio(p);
1396 	if (s)
1397 		return s->irq;
1398 	return PARPORT_IRQ_NONE;
1399 }
1400 
1401 
1402 /* --- Mode detection ------------------------------------- */
1403 
1404 /*
1405  * Checks for port existence, all ports support SPP MODE
1406  * Returns:
1407  *         0           :  No parallel port at this address
1408  *  PARPORT_MODE_PCSPP :  SPP port detected
1409  *                        (if the user specified an ioport himself,
1410  *                         this shall always be the case!)
1411  *
1412  */
parport_SPP_supported(struct parport * pb)1413 static int parport_SPP_supported(struct parport *pb)
1414 {
1415 	unsigned char r, w;
1416 
1417 	/*
1418 	 * first clear an eventually pending EPP timeout
1419 	 * I (sailer@ife.ee.ethz.ch) have an SMSC chipset
1420 	 * that does not even respond to SPP cycles if an EPP
1421 	 * timeout is pending
1422 	 */
1423 	clear_epp_timeout(pb);
1424 
1425 	/* Do a simple read-write test to make sure the port exists. */
1426 	w = 0xc;
1427 	outb(w, CONTROL(pb));
1428 
1429 	/* Is there a control register that we can read from?  Some
1430 	 * ports don't allow reads, so read_control just returns a
1431 	 * software copy. Some ports _do_ allow reads, so bypass the
1432 	 * software copy here.  In addition, some bits aren't
1433 	 * writable. */
1434 	r = inb(CONTROL(pb));
1435 	if ((r & 0xf) == w) {
1436 		w = 0xe;
1437 		outb(w, CONTROL(pb));
1438 		r = inb(CONTROL(pb));
1439 		outb(0xc, CONTROL(pb));
1440 		if ((r & 0xf) == w)
1441 			return PARPORT_MODE_PCSPP;
1442 	}
1443 
1444 	if (user_specified)
1445 		/* That didn't work, but the user thinks there's a
1446 		 * port here. */
1447 		printk(KERN_INFO "parport 0x%lx (WARNING): CTR: "
1448 			"wrote 0x%02x, read 0x%02x\n", pb->base, w, r);
1449 
1450 	/* Try the data register.  The data lines aren't tri-stated at
1451 	 * this stage, so we expect back what we wrote. */
1452 	w = 0xaa;
1453 	parport_pc_write_data(pb, w);
1454 	r = parport_pc_read_data(pb);
1455 	if (r == w) {
1456 		w = 0x55;
1457 		parport_pc_write_data(pb, w);
1458 		r = parport_pc_read_data(pb);
1459 		if (r == w)
1460 			return PARPORT_MODE_PCSPP;
1461 	}
1462 
1463 	if (user_specified) {
1464 		/* Didn't work, but the user is convinced this is the
1465 		 * place. */
1466 		printk(KERN_INFO "parport 0x%lx (WARNING): DATA: "
1467 			"wrote 0x%02x, read 0x%02x\n", pb->base, w, r);
1468 		printk(KERN_INFO "parport 0x%lx: You gave this address, "
1469 			"but there is probably no parallel port there!\n",
1470 			pb->base);
1471 	}
1472 
1473 	/* It's possible that we can't read the control register or
1474 	 * the data register.  In that case just believe the user. */
1475 	if (user_specified)
1476 		return PARPORT_MODE_PCSPP;
1477 
1478 	return 0;
1479 }
1480 
1481 /* Check for ECR
1482  *
1483  * Old style XT ports alias io ports every 0x400, hence accessing ECR
1484  * on these cards actually accesses the CTR.
1485  *
1486  * Modern cards don't do this but reading from ECR will return 0xff
1487  * regardless of what is written here if the card does NOT support
1488  * ECP.
1489  *
1490  * We first check to see if ECR is the same as CTR.  If not, the low
1491  * two bits of ECR aren't writable, so we check by writing ECR and
1492  * reading it back to see if it's what we expect.
1493  */
parport_ECR_present(struct parport * pb)1494 static int parport_ECR_present(struct parport *pb)
1495 {
1496 	struct parport_pc_private *priv = pb->private_data;
1497 	unsigned char r = 0xc;
1498 
1499 	outb(r, CONTROL(pb));
1500 	if ((inb(ECONTROL(pb)) & 0x3) == (r & 0x3)) {
1501 		outb(r ^ 0x2, CONTROL(pb)); /* Toggle bit 1 */
1502 
1503 		r = inb(CONTROL(pb));
1504 		if ((inb(ECONTROL(pb)) & 0x2) == (r & 0x2))
1505 			goto no_reg; /* Sure that no ECR register exists */
1506 	}
1507 
1508 	if ((inb(ECONTROL(pb)) & 0x3) != 0x1)
1509 		goto no_reg;
1510 
1511 	ECR_WRITE(pb, 0x34);
1512 	if (inb(ECONTROL(pb)) != 0x35)
1513 		goto no_reg;
1514 
1515 	priv->ecr = 1;
1516 	outb(0xc, CONTROL(pb));
1517 
1518 	/* Go to mode 000 */
1519 	frob_set_mode(pb, ECR_SPP);
1520 
1521 	return 1;
1522 
1523  no_reg:
1524 	outb(0xc, CONTROL(pb));
1525 	return 0;
1526 }
1527 
1528 #ifdef CONFIG_PARPORT_1284
1529 /* Detect PS/2 support.
1530  *
1531  * Bit 5 (0x20) sets the PS/2 data direction; setting this high
1532  * allows us to read data from the data lines.  In theory we would get back
1533  * 0xff but any peripheral attached to the port may drag some or all of the
1534  * lines down to zero.  So if we get back anything that isn't the contents
1535  * of the data register we deem PS/2 support to be present.
1536  *
1537  * Some SPP ports have "half PS/2" ability - you can't turn off the line
1538  * drivers, but an external peripheral with sufficiently beefy drivers of
1539  * its own can overpower them and assert its own levels onto the bus, from
1540  * where they can then be read back as normal.  Ports with this property
1541  * and the right type of device attached are likely to fail the SPP test,
1542  * (as they will appear to have stuck bits) and so the fact that they might
1543  * be misdetected here is rather academic.
1544  */
1545 
parport_PS2_supported(struct parport * pb)1546 static int parport_PS2_supported(struct parport *pb)
1547 {
1548 	int ok = 0;
1549 
1550 	clear_epp_timeout(pb);
1551 
1552 	/* try to tri-state the buffer */
1553 	parport_pc_data_reverse(pb);
1554 
1555 	parport_pc_write_data(pb, 0x55);
1556 	if (parport_pc_read_data(pb) != 0x55)
1557 		ok++;
1558 
1559 	parport_pc_write_data(pb, 0xaa);
1560 	if (parport_pc_read_data(pb) != 0xaa)
1561 		ok++;
1562 
1563 	/* cancel input mode */
1564 	parport_pc_data_forward(pb);
1565 
1566 	if (ok) {
1567 		pb->modes |= PARPORT_MODE_TRISTATE;
1568 	} else {
1569 		struct parport_pc_private *priv = pb->private_data;
1570 		priv->ctr_writable &= ~0x20;
1571 	}
1572 
1573 	return ok;
1574 }
1575 
1576 #ifdef CONFIG_PARPORT_PC_FIFO
parport_ECP_supported(struct parport * pb)1577 static int parport_ECP_supported(struct parport *pb)
1578 {
1579 	int i;
1580 	int config, configb;
1581 	int pword;
1582 	struct parport_pc_private *priv = pb->private_data;
1583 	/* Translate ECP intrLine to ISA irq value */
1584 	static const int intrline[] = { 0, 7, 9, 10, 11, 14, 15, 5 };
1585 
1586 	/* If there is no ECR, we have no hope of supporting ECP. */
1587 	if (!priv->ecr)
1588 		return 0;
1589 
1590 	/* Find out FIFO depth */
1591 	ECR_WRITE(pb, ECR_SPP << 5); /* Reset FIFO */
1592 	ECR_WRITE(pb, ECR_TST << 5); /* TEST FIFO */
1593 	for (i = 0; i < 1024 && !(inb(ECONTROL(pb)) & 0x02); i++)
1594 		outb(0xaa, FIFO(pb));
1595 
1596 	/*
1597 	 * Using LGS chipset it uses ECR register, but
1598 	 * it doesn't support ECP or FIFO MODE
1599 	 */
1600 	if (i == 1024) {
1601 		ECR_WRITE(pb, ECR_SPP << 5);
1602 		return 0;
1603 	}
1604 
1605 	priv->fifo_depth = i;
1606 	if (verbose_probing)
1607 		printk(KERN_DEBUG "0x%lx: FIFO is %d bytes\n", pb->base, i);
1608 
1609 	/* Find out writeIntrThreshold */
1610 	frob_econtrol(pb, 1<<2, 1<<2);
1611 	frob_econtrol(pb, 1<<2, 0);
1612 	for (i = 1; i <= priv->fifo_depth; i++) {
1613 		inb(FIFO(pb));
1614 		udelay(50);
1615 		if (inb(ECONTROL(pb)) & (1<<2))
1616 			break;
1617 	}
1618 
1619 	if (i <= priv->fifo_depth) {
1620 		if (verbose_probing)
1621 			printk(KERN_DEBUG "0x%lx: writeIntrThreshold is %d\n",
1622 				pb->base, i);
1623 	} else
1624 		/* Number of bytes we know we can write if we get an
1625 		   interrupt. */
1626 		i = 0;
1627 
1628 	priv->writeIntrThreshold = i;
1629 
1630 	/* Find out readIntrThreshold */
1631 	frob_set_mode(pb, ECR_PS2); /* Reset FIFO and enable PS2 */
1632 	parport_pc_data_reverse(pb); /* Must be in PS2 mode */
1633 	frob_set_mode(pb, ECR_TST); /* Test FIFO */
1634 	frob_econtrol(pb, 1<<2, 1<<2);
1635 	frob_econtrol(pb, 1<<2, 0);
1636 	for (i = 1; i <= priv->fifo_depth; i++) {
1637 		outb(0xaa, FIFO(pb));
1638 		if (inb(ECONTROL(pb)) & (1<<2))
1639 			break;
1640 	}
1641 
1642 	if (i <= priv->fifo_depth) {
1643 		if (verbose_probing)
1644 			printk(KERN_INFO "0x%lx: readIntrThreshold is %d\n",
1645 				pb->base, i);
1646 	} else
1647 		/* Number of bytes we can read if we get an interrupt. */
1648 		i = 0;
1649 
1650 	priv->readIntrThreshold = i;
1651 
1652 	ECR_WRITE(pb, ECR_SPP << 5); /* Reset FIFO */
1653 	ECR_WRITE(pb, 0xf4); /* Configuration mode */
1654 	config = inb(CONFIGA(pb));
1655 	pword = (config >> 4) & 0x7;
1656 	switch (pword) {
1657 	case 0:
1658 		pword = 2;
1659 		printk(KERN_WARNING "0x%lx: Unsupported pword size!\n",
1660 			pb->base);
1661 		break;
1662 	case 2:
1663 		pword = 4;
1664 		printk(KERN_WARNING "0x%lx: Unsupported pword size!\n",
1665 			pb->base);
1666 		break;
1667 	default:
1668 		printk(KERN_WARNING "0x%lx: Unknown implementation ID\n",
1669 			pb->base);
1670 		/* Assume 1 */
1671 	case 1:
1672 		pword = 1;
1673 	}
1674 	priv->pword = pword;
1675 
1676 	if (verbose_probing) {
1677 		printk(KERN_DEBUG "0x%lx: PWord is %d bits\n",
1678 			pb->base, 8 * pword);
1679 
1680 		printk(KERN_DEBUG "0x%lx: Interrupts are ISA-%s\n", pb->base,
1681 			config & 0x80 ? "Level" : "Pulses");
1682 
1683 		configb = inb(CONFIGB(pb));
1684 		printk(KERN_DEBUG "0x%lx: ECP port cfgA=0x%02x cfgB=0x%02x\n",
1685 			pb->base, config, configb);
1686 		printk(KERN_DEBUG "0x%lx: ECP settings irq=", pb->base);
1687 		if ((configb >> 3) & 0x07)
1688 			pr_cont("%d", intrline[(configb >> 3) & 0x07]);
1689 		else
1690 			pr_cont("<none or set by other means>");
1691 		pr_cont(" dma=");
1692 		if ((configb & 0x03) == 0x00)
1693 			pr_cont("<none or set by other means>\n");
1694 		else
1695 			pr_cont("%d\n", configb & 0x07);
1696 	}
1697 
1698 	/* Go back to mode 000 */
1699 	frob_set_mode(pb, ECR_SPP);
1700 
1701 	return 1;
1702 }
1703 #endif
1704 
1705 #ifdef CONFIG_X86_32
intel_bug_present_check_epp(struct parport * pb)1706 static int intel_bug_present_check_epp(struct parport *pb)
1707 {
1708 	const struct parport_pc_private *priv = pb->private_data;
1709 	int bug_present = 0;
1710 
1711 	if (priv->ecr) {
1712 		/* store value of ECR */
1713 		unsigned char ecr = inb(ECONTROL(pb));
1714 		unsigned char i;
1715 		for (i = 0x00; i < 0x80; i += 0x20) {
1716 			ECR_WRITE(pb, i);
1717 			if (clear_epp_timeout(pb)) {
1718 				/* Phony EPP in ECP. */
1719 				bug_present = 1;
1720 				break;
1721 			}
1722 		}
1723 		/* return ECR into the inital state */
1724 		ECR_WRITE(pb, ecr);
1725 	}
1726 
1727 	return bug_present;
1728 }
intel_bug_present(struct parport * pb)1729 static int intel_bug_present(struct parport *pb)
1730 {
1731 /* Check whether the device is legacy, not PCI or PCMCIA. Only legacy is known to be affected. */
1732 	if (pb->dev != NULL) {
1733 		return 0;
1734 	}
1735 
1736 	return intel_bug_present_check_epp(pb);
1737 }
1738 #else
intel_bug_present(struct parport * pb)1739 static int intel_bug_present(struct parport *pb)
1740 {
1741 	return 0;
1742 }
1743 #endif /* CONFIG_X86_32 */
1744 
parport_ECPPS2_supported(struct parport * pb)1745 static int parport_ECPPS2_supported(struct parport *pb)
1746 {
1747 	const struct parport_pc_private *priv = pb->private_data;
1748 	int result;
1749 	unsigned char oecr;
1750 
1751 	if (!priv->ecr)
1752 		return 0;
1753 
1754 	oecr = inb(ECONTROL(pb));
1755 	ECR_WRITE(pb, ECR_PS2 << 5);
1756 	result = parport_PS2_supported(pb);
1757 	ECR_WRITE(pb, oecr);
1758 	return result;
1759 }
1760 
1761 /* EPP mode detection  */
1762 
parport_EPP_supported(struct parport * pb)1763 static int parport_EPP_supported(struct parport *pb)
1764 {
1765 	/*
1766 	 * Theory:
1767 	 *	Bit 0 of STR is the EPP timeout bit, this bit is 0
1768 	 *	when EPP is possible and is set high when an EPP timeout
1769 	 *	occurs (EPP uses the HALT line to stop the CPU while it does
1770 	 *	the byte transfer, an EPP timeout occurs if the attached
1771 	 *	device fails to respond after 10 micro seconds).
1772 	 *
1773 	 *	This bit is cleared by either reading it (National Semi)
1774 	 *	or writing a 1 to the bit (SMC, UMC, WinBond), others ???
1775 	 *	This bit is always high in non EPP modes.
1776 	 */
1777 
1778 	/* If EPP timeout bit clear then EPP available */
1779 	if (!clear_epp_timeout(pb))
1780 		return 0;  /* No way to clear timeout */
1781 
1782 	/* Check for Intel bug. */
1783 	if (intel_bug_present(pb))
1784 		return 0;
1785 
1786 	pb->modes |= PARPORT_MODE_EPP;
1787 
1788 	/* Set up access functions to use EPP hardware. */
1789 	pb->ops->epp_read_data = parport_pc_epp_read_data;
1790 	pb->ops->epp_write_data = parport_pc_epp_write_data;
1791 	pb->ops->epp_read_addr = parport_pc_epp_read_addr;
1792 	pb->ops->epp_write_addr = parport_pc_epp_write_addr;
1793 
1794 	return 1;
1795 }
1796 
parport_ECPEPP_supported(struct parport * pb)1797 static int parport_ECPEPP_supported(struct parport *pb)
1798 {
1799 	struct parport_pc_private *priv = pb->private_data;
1800 	int result;
1801 	unsigned char oecr;
1802 
1803 	if (!priv->ecr)
1804 		return 0;
1805 
1806 	oecr = inb(ECONTROL(pb));
1807 	/* Search for SMC style EPP+ECP mode */
1808 	ECR_WRITE(pb, 0x80);
1809 	outb(0x04, CONTROL(pb));
1810 	result = parport_EPP_supported(pb);
1811 
1812 	ECR_WRITE(pb, oecr);
1813 
1814 	if (result) {
1815 		/* Set up access functions to use ECP+EPP hardware. */
1816 		pb->ops->epp_read_data = parport_pc_ecpepp_read_data;
1817 		pb->ops->epp_write_data = parport_pc_ecpepp_write_data;
1818 		pb->ops->epp_read_addr = parport_pc_ecpepp_read_addr;
1819 		pb->ops->epp_write_addr = parport_pc_ecpepp_write_addr;
1820 	}
1821 
1822 	return result;
1823 }
1824 
1825 #else /* No IEEE 1284 support */
1826 
1827 /* Don't bother probing for modes we know we won't use. */
parport_PS2_supported(struct parport * pb)1828 static int parport_PS2_supported(struct parport *pb) { return 0; }
1829 #ifdef CONFIG_PARPORT_PC_FIFO
parport_ECP_supported(struct parport * pb)1830 static int parport_ECP_supported(struct parport *pb)
1831 {
1832 	return 0;
1833 }
1834 #endif
parport_EPP_supported(struct parport * pb)1835 static int parport_EPP_supported(struct parport *pb)
1836 {
1837 	return 0;
1838 }
1839 
parport_ECPEPP_supported(struct parport * pb)1840 static int parport_ECPEPP_supported(struct parport *pb)
1841 {
1842 	return 0;
1843 }
1844 
parport_ECPPS2_supported(struct parport * pb)1845 static int parport_ECPPS2_supported(struct parport *pb)
1846 {
1847 	return 0;
1848 }
1849 
1850 #endif /* No IEEE 1284 support */
1851 
1852 /* --- IRQ detection -------------------------------------- */
1853 
1854 /* Only if supports ECP mode */
programmable_irq_support(struct parport * pb)1855 static int programmable_irq_support(struct parport *pb)
1856 {
1857 	int irq, intrLine;
1858 	unsigned char oecr = inb(ECONTROL(pb));
1859 	static const int lookup[8] = {
1860 		PARPORT_IRQ_NONE, 7, 9, 10, 11, 14, 15, 5
1861 	};
1862 
1863 	ECR_WRITE(pb, ECR_CNF << 5); /* Configuration MODE */
1864 
1865 	intrLine = (inb(CONFIGB(pb)) >> 3) & 0x07;
1866 	irq = lookup[intrLine];
1867 
1868 	ECR_WRITE(pb, oecr);
1869 	return irq;
1870 }
1871 
irq_probe_ECP(struct parport * pb)1872 static int irq_probe_ECP(struct parport *pb)
1873 {
1874 	int i;
1875 	unsigned long irqs;
1876 
1877 	irqs = probe_irq_on();
1878 
1879 	ECR_WRITE(pb, ECR_SPP << 5); /* Reset FIFO */
1880 	ECR_WRITE(pb, (ECR_TST << 5) | 0x04);
1881 	ECR_WRITE(pb, ECR_TST << 5);
1882 
1883 	/* If Full FIFO sure that writeIntrThreshold is generated */
1884 	for (i = 0; i < 1024 && !(inb(ECONTROL(pb)) & 0x02) ; i++)
1885 		outb(0xaa, FIFO(pb));
1886 
1887 	pb->irq = probe_irq_off(irqs);
1888 	ECR_WRITE(pb, ECR_SPP << 5);
1889 
1890 	if (pb->irq <= 0)
1891 		pb->irq = PARPORT_IRQ_NONE;
1892 
1893 	return pb->irq;
1894 }
1895 
1896 /*
1897  * This detection seems that only works in National Semiconductors
1898  * This doesn't work in SMC, LGS, and Winbond
1899  */
irq_probe_EPP(struct parport * pb)1900 static int irq_probe_EPP(struct parport *pb)
1901 {
1902 #ifndef ADVANCED_DETECT
1903 	return PARPORT_IRQ_NONE;
1904 #else
1905 	int irqs;
1906 	unsigned char oecr;
1907 
1908 	if (pb->modes & PARPORT_MODE_PCECR)
1909 		oecr = inb(ECONTROL(pb));
1910 
1911 	irqs = probe_irq_on();
1912 
1913 	if (pb->modes & PARPORT_MODE_PCECR)
1914 		frob_econtrol(pb, 0x10, 0x10);
1915 
1916 	clear_epp_timeout(pb);
1917 	parport_pc_frob_control(pb, 0x20, 0x20);
1918 	parport_pc_frob_control(pb, 0x10, 0x10);
1919 	clear_epp_timeout(pb);
1920 
1921 	/* Device isn't expecting an EPP read
1922 	 * and generates an IRQ.
1923 	 */
1924 	parport_pc_read_epp(pb);
1925 	udelay(20);
1926 
1927 	pb->irq = probe_irq_off(irqs);
1928 	if (pb->modes & PARPORT_MODE_PCECR)
1929 		ECR_WRITE(pb, oecr);
1930 	parport_pc_write_control(pb, 0xc);
1931 
1932 	if (pb->irq <= 0)
1933 		pb->irq = PARPORT_IRQ_NONE;
1934 
1935 	return pb->irq;
1936 #endif /* Advanced detection */
1937 }
1938 
irq_probe_SPP(struct parport * pb)1939 static int irq_probe_SPP(struct parport *pb)
1940 {
1941 	/* Don't even try to do this. */
1942 	return PARPORT_IRQ_NONE;
1943 }
1944 
1945 /* We will attempt to share interrupt requests since other devices
1946  * such as sound cards and network cards seem to like using the
1947  * printer IRQs.
1948  *
1949  * When ECP is available we can autoprobe for IRQs.
1950  * NOTE: If we can autoprobe it, we can register the IRQ.
1951  */
parport_irq_probe(struct parport * pb)1952 static int parport_irq_probe(struct parport *pb)
1953 {
1954 	struct parport_pc_private *priv = pb->private_data;
1955 
1956 	if (priv->ecr) {
1957 		pb->irq = programmable_irq_support(pb);
1958 
1959 		if (pb->irq == PARPORT_IRQ_NONE)
1960 			pb->irq = irq_probe_ECP(pb);
1961 	}
1962 
1963 	if ((pb->irq == PARPORT_IRQ_NONE) && priv->ecr &&
1964 	    (pb->modes & PARPORT_MODE_EPP))
1965 		pb->irq = irq_probe_EPP(pb);
1966 
1967 	clear_epp_timeout(pb);
1968 
1969 	if (pb->irq == PARPORT_IRQ_NONE && (pb->modes & PARPORT_MODE_EPP))
1970 		pb->irq = irq_probe_EPP(pb);
1971 
1972 	clear_epp_timeout(pb);
1973 
1974 	if (pb->irq == PARPORT_IRQ_NONE)
1975 		pb->irq = irq_probe_SPP(pb);
1976 
1977 	if (pb->irq == PARPORT_IRQ_NONE)
1978 		pb->irq = get_superio_irq(pb);
1979 
1980 	return pb->irq;
1981 }
1982 
1983 /* --- DMA detection -------------------------------------- */
1984 
1985 /* Only if chipset conforms to ECP ISA Interface Standard */
programmable_dma_support(struct parport * p)1986 static int programmable_dma_support(struct parport *p)
1987 {
1988 	unsigned char oecr = inb(ECONTROL(p));
1989 	int dma;
1990 
1991 	frob_set_mode(p, ECR_CNF);
1992 
1993 	dma = inb(CONFIGB(p)) & 0x07;
1994 	/* 000: Indicates jumpered 8-bit DMA if read-only.
1995 	   100: Indicates jumpered 16-bit DMA if read-only. */
1996 	if ((dma & 0x03) == 0)
1997 		dma = PARPORT_DMA_NONE;
1998 
1999 	ECR_WRITE(p, oecr);
2000 	return dma;
2001 }
2002 
parport_dma_probe(struct parport * p)2003 static int parport_dma_probe(struct parport *p)
2004 {
2005 	const struct parport_pc_private *priv = p->private_data;
2006 	if (priv->ecr)		/* ask ECP chipset first */
2007 		p->dma = programmable_dma_support(p);
2008 	if (p->dma == PARPORT_DMA_NONE) {
2009 		/* ask known Super-IO chips proper, although these
2010 		   claim ECP compatible, some don't report their DMA
2011 		   conforming to ECP standards */
2012 		p->dma = get_superio_dma(p);
2013 	}
2014 
2015 	return p->dma;
2016 }
2017 
2018 /* --- Initialisation code -------------------------------- */
2019 
2020 static LIST_HEAD(ports_list);
2021 static DEFINE_SPINLOCK(ports_lock);
2022 
parport_pc_probe_port(unsigned long int base,unsigned long int base_hi,int irq,int dma,struct device * dev,int irqflags)2023 struct parport *parport_pc_probe_port(unsigned long int base,
2024 				      unsigned long int base_hi,
2025 				      int irq, int dma,
2026 				      struct device *dev,
2027 				      int irqflags)
2028 {
2029 	struct parport_pc_private *priv;
2030 	struct parport_operations *ops;
2031 	struct parport *p;
2032 	int probedirq = PARPORT_IRQ_NONE;
2033 	struct resource *base_res;
2034 	struct resource	*ECR_res = NULL;
2035 	struct resource	*EPP_res = NULL;
2036 	struct platform_device *pdev = NULL;
2037 	int ret;
2038 
2039 	if (!dev) {
2040 		/* We need a physical device to attach to, but none was
2041 		 * provided. Create our own. */
2042 		pdev = platform_device_register_simple("parport_pc",
2043 						       base, NULL, 0);
2044 		if (IS_ERR(pdev))
2045 			return NULL;
2046 		dev = &pdev->dev;
2047 
2048 		ret = dma_coerce_mask_and_coherent(dev, DMA_BIT_MASK(24));
2049 		if (ret) {
2050 			dev_err(dev, "Unable to set coherent dma mask: disabling DMA\n");
2051 			dma = PARPORT_DMA_NONE;
2052 		}
2053 	}
2054 
2055 	ops = kmalloc(sizeof(struct parport_operations), GFP_KERNEL);
2056 	if (!ops)
2057 		goto out1;
2058 
2059 	priv = kmalloc(sizeof(struct parport_pc_private), GFP_KERNEL);
2060 	if (!priv)
2061 		goto out2;
2062 
2063 	/* a misnomer, actually - it's allocate and reserve parport number */
2064 	p = parport_register_port(base, irq, dma, ops);
2065 	if (!p)
2066 		goto out3;
2067 
2068 	base_res = request_region(base, 3, p->name);
2069 	if (!base_res)
2070 		goto out4;
2071 
2072 	memcpy(ops, &parport_pc_ops, sizeof(struct parport_operations));
2073 	priv->ctr = 0xc;
2074 	priv->ctr_writable = ~0x10;
2075 	priv->ecr = 0;
2076 	priv->fifo_depth = 0;
2077 	priv->dma_buf = NULL;
2078 	priv->dma_handle = 0;
2079 	INIT_LIST_HEAD(&priv->list);
2080 	priv->port = p;
2081 
2082 	p->dev = dev;
2083 	p->base_hi = base_hi;
2084 	p->modes = PARPORT_MODE_PCSPP | PARPORT_MODE_SAFEININT;
2085 	p->private_data = priv;
2086 
2087 	if (base_hi) {
2088 		ECR_res = request_region(base_hi, 3, p->name);
2089 		if (ECR_res)
2090 			parport_ECR_present(p);
2091 	}
2092 
2093 	if (base != 0x3bc) {
2094 		EPP_res = request_region(base+0x3, 5, p->name);
2095 		if (EPP_res)
2096 			if (!parport_EPP_supported(p))
2097 				parport_ECPEPP_supported(p);
2098 	}
2099 	if (!parport_SPP_supported(p))
2100 		/* No port. */
2101 		goto out5;
2102 	if (priv->ecr)
2103 		parport_ECPPS2_supported(p);
2104 	else
2105 		parport_PS2_supported(p);
2106 
2107 	p->size = (p->modes & PARPORT_MODE_EPP) ? 8 : 3;
2108 
2109 	printk(KERN_INFO "%s: PC-style at 0x%lx", p->name, p->base);
2110 	if (p->base_hi && priv->ecr)
2111 		printk(KERN_CONT " (0x%lx)", p->base_hi);
2112 	if (p->irq == PARPORT_IRQ_AUTO) {
2113 		p->irq = PARPORT_IRQ_NONE;
2114 		parport_irq_probe(p);
2115 	} else if (p->irq == PARPORT_IRQ_PROBEONLY) {
2116 		p->irq = PARPORT_IRQ_NONE;
2117 		parport_irq_probe(p);
2118 		probedirq = p->irq;
2119 		p->irq = PARPORT_IRQ_NONE;
2120 	}
2121 	if (p->irq != PARPORT_IRQ_NONE) {
2122 		printk(KERN_CONT ", irq %d", p->irq);
2123 		priv->ctr_writable |= 0x10;
2124 
2125 		if (p->dma == PARPORT_DMA_AUTO) {
2126 			p->dma = PARPORT_DMA_NONE;
2127 			parport_dma_probe(p);
2128 		}
2129 	}
2130 	if (p->dma == PARPORT_DMA_AUTO) /* To use DMA, giving the irq
2131 					   is mandatory (see above) */
2132 		p->dma = PARPORT_DMA_NONE;
2133 
2134 #ifdef CONFIG_PARPORT_PC_FIFO
2135 	if (parport_ECP_supported(p) &&
2136 	    p->dma != PARPORT_DMA_NOFIFO &&
2137 	    priv->fifo_depth > 0 && p->irq != PARPORT_IRQ_NONE) {
2138 		p->modes |= PARPORT_MODE_ECP | PARPORT_MODE_COMPAT;
2139 		p->ops->compat_write_data = parport_pc_compat_write_block_pio;
2140 #ifdef CONFIG_PARPORT_1284
2141 		p->ops->ecp_write_data = parport_pc_ecp_write_block_pio;
2142 		/* currently broken, but working on it.. (FB) */
2143 		/* p->ops->ecp_read_data = parport_pc_ecp_read_block_pio; */
2144 #endif /* IEEE 1284 support */
2145 		if (p->dma != PARPORT_DMA_NONE) {
2146 			printk(KERN_CONT ", dma %d", p->dma);
2147 			p->modes |= PARPORT_MODE_DMA;
2148 		} else
2149 			printk(KERN_CONT ", using FIFO");
2150 	} else
2151 		/* We can't use the DMA channel after all. */
2152 		p->dma = PARPORT_DMA_NONE;
2153 #endif /* Allowed to use FIFO/DMA */
2154 
2155 	printk(KERN_CONT " [");
2156 
2157 #define printmode(x) \
2158 	{\
2159 		if (p->modes & PARPORT_MODE_##x) {\
2160 			printk(KERN_CONT "%s%s", f ? "," : "", #x);\
2161 			f++;\
2162 		} \
2163 	}
2164 
2165 	{
2166 		int f = 0;
2167 		printmode(PCSPP);
2168 		printmode(TRISTATE);
2169 		printmode(COMPAT)
2170 		printmode(EPP);
2171 		printmode(ECP);
2172 		printmode(DMA);
2173 	}
2174 #undef printmode
2175 #ifndef CONFIG_PARPORT_1284
2176 	printk(KERN_CONT "(,...)");
2177 #endif /* CONFIG_PARPORT_1284 */
2178 	printk(KERN_CONT "]\n");
2179 	if (probedirq != PARPORT_IRQ_NONE)
2180 		printk(KERN_INFO "%s: irq %d detected\n", p->name, probedirq);
2181 
2182 	/* If No ECP release the ports grabbed above. */
2183 	if (ECR_res && (p->modes & PARPORT_MODE_ECP) == 0) {
2184 		release_region(base_hi, 3);
2185 		ECR_res = NULL;
2186 	}
2187 	/* Likewise for EEP ports */
2188 	if (EPP_res && (p->modes & PARPORT_MODE_EPP) == 0) {
2189 		release_region(base+3, 5);
2190 		EPP_res = NULL;
2191 	}
2192 	if (p->irq != PARPORT_IRQ_NONE) {
2193 		if (request_irq(p->irq, parport_irq_handler,
2194 				 irqflags, p->name, p)) {
2195 			printk(KERN_WARNING "%s: irq %d in use, "
2196 				"resorting to polled operation\n",
2197 				p->name, p->irq);
2198 			p->irq = PARPORT_IRQ_NONE;
2199 			p->dma = PARPORT_DMA_NONE;
2200 		}
2201 
2202 #ifdef CONFIG_PARPORT_PC_FIFO
2203 #ifdef HAS_DMA
2204 		if (p->dma != PARPORT_DMA_NONE) {
2205 			if (request_dma(p->dma, p->name)) {
2206 				printk(KERN_WARNING "%s: dma %d in use, "
2207 					"resorting to PIO operation\n",
2208 					p->name, p->dma);
2209 				p->dma = PARPORT_DMA_NONE;
2210 			} else {
2211 				priv->dma_buf =
2212 				  dma_alloc_coherent(dev,
2213 						       PAGE_SIZE,
2214 						       &priv->dma_handle,
2215 						       GFP_KERNEL);
2216 				if (!priv->dma_buf) {
2217 					printk(KERN_WARNING "%s: "
2218 						"cannot get buffer for DMA, "
2219 						"resorting to PIO operation\n",
2220 						p->name);
2221 					free_dma(p->dma);
2222 					p->dma = PARPORT_DMA_NONE;
2223 				}
2224 			}
2225 		}
2226 #endif
2227 #endif
2228 	}
2229 
2230 	/* Done probing.  Now put the port into a sensible start-up state. */
2231 	if (priv->ecr)
2232 		/*
2233 		 * Put the ECP detected port in PS2 mode.
2234 		 * Do this also for ports that have ECR but don't do ECP.
2235 		 */
2236 		ECR_WRITE(p, 0x34);
2237 
2238 	parport_pc_write_data(p, 0);
2239 	parport_pc_data_forward(p);
2240 
2241 	/* Now that we've told the sharing engine about the port, and
2242 	   found out its characteristics, let the high-level drivers
2243 	   know about it. */
2244 	spin_lock(&ports_lock);
2245 	list_add(&priv->list, &ports_list);
2246 	spin_unlock(&ports_lock);
2247 	parport_announce_port(p);
2248 
2249 	return p;
2250 
2251 out5:
2252 	if (ECR_res)
2253 		release_region(base_hi, 3);
2254 	if (EPP_res)
2255 		release_region(base+0x3, 5);
2256 	release_region(base, 3);
2257 out4:
2258 	parport_del_port(p);
2259 out3:
2260 	kfree(priv);
2261 out2:
2262 	kfree(ops);
2263 out1:
2264 	if (pdev)
2265 		platform_device_unregister(pdev);
2266 	return NULL;
2267 }
2268 EXPORT_SYMBOL(parport_pc_probe_port);
2269 
parport_pc_unregister_port(struct parport * p)2270 void parport_pc_unregister_port(struct parport *p)
2271 {
2272 	struct parport_pc_private *priv = p->private_data;
2273 	struct parport_operations *ops = p->ops;
2274 
2275 	parport_remove_port(p);
2276 	spin_lock(&ports_lock);
2277 	list_del_init(&priv->list);
2278 	spin_unlock(&ports_lock);
2279 #if defined(CONFIG_PARPORT_PC_FIFO) && defined(HAS_DMA)
2280 	if (p->dma != PARPORT_DMA_NONE)
2281 		free_dma(p->dma);
2282 #endif
2283 	if (p->irq != PARPORT_IRQ_NONE)
2284 		free_irq(p->irq, p);
2285 	release_region(p->base, 3);
2286 	if (p->size > 3)
2287 		release_region(p->base + 3, p->size - 3);
2288 	if (p->modes & PARPORT_MODE_ECP)
2289 		release_region(p->base_hi, 3);
2290 #if defined(CONFIG_PARPORT_PC_FIFO) && defined(HAS_DMA)
2291 	if (priv->dma_buf)
2292 		dma_free_coherent(p->physport->dev, PAGE_SIZE,
2293 				    priv->dma_buf,
2294 				    priv->dma_handle);
2295 #endif
2296 	kfree(p->private_data);
2297 	parport_del_port(p);
2298 	kfree(ops); /* hope no-one cached it */
2299 }
2300 EXPORT_SYMBOL(parport_pc_unregister_port);
2301 
2302 #ifdef CONFIG_PCI
2303 
2304 /* ITE support maintained by Rich Liu <richliu@poorman.org> */
sio_ite_8872_probe(struct pci_dev * pdev,int autoirq,int autodma,const struct parport_pc_via_data * via)2305 static int sio_ite_8872_probe(struct pci_dev *pdev, int autoirq, int autodma,
2306 			      const struct parport_pc_via_data *via)
2307 {
2308 	short inta_addr[6] = { 0x2A0, 0x2C0, 0x220, 0x240, 0x1E0 };
2309 	u32 ite8872set;
2310 	u32 ite8872_lpt, ite8872_lpthi;
2311 	u8 ite8872_irq, type;
2312 	int irq;
2313 	int i;
2314 
2315 	DPRINTK(KERN_DEBUG "sio_ite_8872_probe()\n");
2316 
2317 	/* make sure which one chip */
2318 	for (i = 0; i < 5; i++) {
2319 		if (request_region(inta_addr[i], 32, "it887x")) {
2320 			int test;
2321 			pci_write_config_dword(pdev, 0x60,
2322 						0xe5000000 | inta_addr[i]);
2323 			pci_write_config_dword(pdev, 0x78,
2324 						0x00000000 | inta_addr[i]);
2325 			test = inb(inta_addr[i]);
2326 			if (test != 0xff)
2327 				break;
2328 			release_region(inta_addr[i], 32);
2329 		}
2330 	}
2331 	if (i >= 5) {
2332 		printk(KERN_INFO "parport_pc: cannot find ITE8872 INTA\n");
2333 		return 0;
2334 	}
2335 
2336 	type = inb(inta_addr[i] + 0x18);
2337 	type &= 0x0f;
2338 
2339 	switch (type) {
2340 	case 0x2:
2341 		printk(KERN_INFO "parport_pc: ITE8871 found (1P)\n");
2342 		ite8872set = 0x64200000;
2343 		break;
2344 	case 0xa:
2345 		printk(KERN_INFO "parport_pc: ITE8875 found (1P)\n");
2346 		ite8872set = 0x64200000;
2347 		break;
2348 	case 0xe:
2349 		printk(KERN_INFO "parport_pc: ITE8872 found (2S1P)\n");
2350 		ite8872set = 0x64e00000;
2351 		break;
2352 	case 0x6:
2353 		printk(KERN_INFO "parport_pc: ITE8873 found (1S)\n");
2354 		release_region(inta_addr[i], 32);
2355 		return 0;
2356 	case 0x8:
2357 		printk(KERN_INFO "parport_pc: ITE8874 found (2S)\n");
2358 		release_region(inta_addr[i], 32);
2359 		return 0;
2360 	default:
2361 		printk(KERN_INFO "parport_pc: unknown ITE887x\n");
2362 		printk(KERN_INFO "parport_pc: please mail 'lspci -nvv' "
2363 			"output to Rich.Liu@ite.com.tw\n");
2364 		release_region(inta_addr[i], 32);
2365 		return 0;
2366 	}
2367 
2368 	pci_read_config_byte(pdev, 0x3c, &ite8872_irq);
2369 	pci_read_config_dword(pdev, 0x1c, &ite8872_lpt);
2370 	ite8872_lpt &= 0x0000ff00;
2371 	pci_read_config_dword(pdev, 0x20, &ite8872_lpthi);
2372 	ite8872_lpthi &= 0x0000ff00;
2373 	pci_write_config_dword(pdev, 0x6c, 0xe3000000 | ite8872_lpt);
2374 	pci_write_config_dword(pdev, 0x70, 0xe3000000 | ite8872_lpthi);
2375 	pci_write_config_dword(pdev, 0x80, (ite8872_lpthi<<16) | ite8872_lpt);
2376 	/* SET SPP&EPP , Parallel Port NO DMA , Enable All Function */
2377 	/* SET Parallel IRQ */
2378 	pci_write_config_dword(pdev, 0x9c,
2379 				ite8872set | (ite8872_irq * 0x11111));
2380 
2381 	DPRINTK(KERN_DEBUG "ITE887x: The IRQ is %d.\n", ite8872_irq);
2382 	DPRINTK(KERN_DEBUG "ITE887x: The PARALLEL I/O port is 0x%x.\n",
2383 		 ite8872_lpt);
2384 	DPRINTK(KERN_DEBUG "ITE887x: The PARALLEL I/O porthi is 0x%x.\n",
2385 		 ite8872_lpthi);
2386 
2387 	/* Let the user (or defaults) steer us away from interrupts */
2388 	irq = ite8872_irq;
2389 	if (autoirq != PARPORT_IRQ_AUTO)
2390 		irq = PARPORT_IRQ_NONE;
2391 
2392 	/*
2393 	 * Release the resource so that parport_pc_probe_port can get it.
2394 	 */
2395 	release_region(inta_addr[i], 32);
2396 	if (parport_pc_probe_port(ite8872_lpt, ite8872_lpthi,
2397 				   irq, PARPORT_DMA_NONE, &pdev->dev, 0)) {
2398 		printk(KERN_INFO
2399 			"parport_pc: ITE 8872 parallel port: io=0x%X",
2400 								ite8872_lpt);
2401 		if (irq != PARPORT_IRQ_NONE)
2402 			pr_cont(", irq=%d", irq);
2403 		pr_cont("\n");
2404 		return 1;
2405 	}
2406 
2407 	return 0;
2408 }
2409 
2410 /* VIA 8231 support by Pavel Fedin <sonic_amiga@rambler.ru>
2411    based on VIA 686a support code by Jeff Garzik <jgarzik@pobox.com> */
2412 static int parport_init_mode;
2413 
2414 /* Data for two known VIA chips */
2415 static struct parport_pc_via_data via_686a_data = {
2416 	0x51,
2417 	0x50,
2418 	0x85,
2419 	0x02,
2420 	0xE2,
2421 	0xF0,
2422 	0xE6
2423 };
2424 static struct parport_pc_via_data via_8231_data = {
2425 	0x45,
2426 	0x44,
2427 	0x50,
2428 	0x04,
2429 	0xF2,
2430 	0xFA,
2431 	0xF6
2432 };
2433 
sio_via_probe(struct pci_dev * pdev,int autoirq,int autodma,const struct parport_pc_via_data * via)2434 static int sio_via_probe(struct pci_dev *pdev, int autoirq, int autodma,
2435 			 const struct parport_pc_via_data *via)
2436 {
2437 	u8 tmp, tmp2, siofunc;
2438 	u8 ppcontrol = 0;
2439 	int dma, irq;
2440 	unsigned port1, port2;
2441 	unsigned have_epp = 0;
2442 
2443 	printk(KERN_DEBUG "parport_pc: VIA 686A/8231 detected\n");
2444 
2445 	switch (parport_init_mode) {
2446 	case 1:
2447 		printk(KERN_DEBUG "parport_pc: setting SPP mode\n");
2448 		siofunc = VIA_FUNCTION_PARPORT_SPP;
2449 		break;
2450 	case 2:
2451 		printk(KERN_DEBUG "parport_pc: setting PS/2 mode\n");
2452 		siofunc = VIA_FUNCTION_PARPORT_SPP;
2453 		ppcontrol = VIA_PARPORT_BIDIR;
2454 		break;
2455 	case 3:
2456 		printk(KERN_DEBUG "parport_pc: setting EPP mode\n");
2457 		siofunc = VIA_FUNCTION_PARPORT_EPP;
2458 		ppcontrol = VIA_PARPORT_BIDIR;
2459 		have_epp = 1;
2460 		break;
2461 	case 4:
2462 		printk(KERN_DEBUG "parport_pc: setting ECP mode\n");
2463 		siofunc = VIA_FUNCTION_PARPORT_ECP;
2464 		ppcontrol = VIA_PARPORT_BIDIR;
2465 		break;
2466 	case 5:
2467 		printk(KERN_DEBUG "parport_pc: setting EPP+ECP mode\n");
2468 		siofunc = VIA_FUNCTION_PARPORT_ECP;
2469 		ppcontrol = VIA_PARPORT_BIDIR|VIA_PARPORT_ECPEPP;
2470 		have_epp = 1;
2471 		break;
2472 	default:
2473 		printk(KERN_DEBUG
2474 			"parport_pc: probing current configuration\n");
2475 		siofunc = VIA_FUNCTION_PROBE;
2476 		break;
2477 	}
2478 	/*
2479 	 * unlock super i/o configuration
2480 	 */
2481 	pci_read_config_byte(pdev, via->via_pci_superio_config_reg, &tmp);
2482 	tmp |= via->via_pci_superio_config_data;
2483 	pci_write_config_byte(pdev, via->via_pci_superio_config_reg, tmp);
2484 
2485 	/* Bits 1-0: Parallel Port Mode / Enable */
2486 	outb(via->viacfg_function, VIA_CONFIG_INDEX);
2487 	tmp = inb(VIA_CONFIG_DATA);
2488 	/* Bit 5: EPP+ECP enable; bit 7: PS/2 bidirectional port enable */
2489 	outb(via->viacfg_parport_control, VIA_CONFIG_INDEX);
2490 	tmp2 = inb(VIA_CONFIG_DATA);
2491 	if (siofunc == VIA_FUNCTION_PROBE) {
2492 		siofunc = tmp & VIA_FUNCTION_PARPORT_DISABLE;
2493 		ppcontrol = tmp2;
2494 	} else {
2495 		tmp &= ~VIA_FUNCTION_PARPORT_DISABLE;
2496 		tmp |= siofunc;
2497 		outb(via->viacfg_function, VIA_CONFIG_INDEX);
2498 		outb(tmp, VIA_CONFIG_DATA);
2499 		tmp2 &= ~(VIA_PARPORT_BIDIR|VIA_PARPORT_ECPEPP);
2500 		tmp2 |= ppcontrol;
2501 		outb(via->viacfg_parport_control, VIA_CONFIG_INDEX);
2502 		outb(tmp2, VIA_CONFIG_DATA);
2503 	}
2504 
2505 	/* Parallel Port I/O Base Address, bits 9-2 */
2506 	outb(via->viacfg_parport_base, VIA_CONFIG_INDEX);
2507 	port1 = inb(VIA_CONFIG_DATA) << 2;
2508 
2509 	printk(KERN_DEBUG "parport_pc: Current parallel port base: 0x%X\n",
2510 									port1);
2511 	if (port1 == 0x3BC && have_epp) {
2512 		outb(via->viacfg_parport_base, VIA_CONFIG_INDEX);
2513 		outb((0x378 >> 2), VIA_CONFIG_DATA);
2514 		printk(KERN_DEBUG
2515 			"parport_pc: Parallel port base changed to 0x378\n");
2516 		port1 = 0x378;
2517 	}
2518 
2519 	/*
2520 	 * lock super i/o configuration
2521 	 */
2522 	pci_read_config_byte(pdev, via->via_pci_superio_config_reg, &tmp);
2523 	tmp &= ~via->via_pci_superio_config_data;
2524 	pci_write_config_byte(pdev, via->via_pci_superio_config_reg, tmp);
2525 
2526 	if (siofunc == VIA_FUNCTION_PARPORT_DISABLE) {
2527 		printk(KERN_INFO "parport_pc: VIA parallel port disabled in BIOS\n");
2528 		return 0;
2529 	}
2530 
2531 	/* Bits 7-4: PnP Routing for Parallel Port IRQ */
2532 	pci_read_config_byte(pdev, via->via_pci_parport_irq_reg, &tmp);
2533 	irq = ((tmp & VIA_IRQCONTROL_PARALLEL) >> 4);
2534 
2535 	if (siofunc == VIA_FUNCTION_PARPORT_ECP) {
2536 		/* Bits 3-2: PnP Routing for Parallel Port DMA */
2537 		pci_read_config_byte(pdev, via->via_pci_parport_dma_reg, &tmp);
2538 		dma = ((tmp & VIA_DMACONTROL_PARALLEL) >> 2);
2539 	} else
2540 		/* if ECP not enabled, DMA is not enabled, assumed
2541 		   bogus 'dma' value */
2542 		dma = PARPORT_DMA_NONE;
2543 
2544 	/* Let the user (or defaults) steer us away from interrupts and DMA */
2545 	if (autoirq == PARPORT_IRQ_NONE) {
2546 		irq = PARPORT_IRQ_NONE;
2547 		dma = PARPORT_DMA_NONE;
2548 	}
2549 	if (autodma == PARPORT_DMA_NONE)
2550 		dma = PARPORT_DMA_NONE;
2551 
2552 	switch (port1) {
2553 	case 0x3bc:
2554 		port2 = 0x7bc; break;
2555 	case 0x378:
2556 		port2 = 0x778; break;
2557 	case 0x278:
2558 		port2 = 0x678; break;
2559 	default:
2560 		printk(KERN_INFO
2561 			"parport_pc: Weird VIA parport base 0x%X, ignoring\n",
2562 									port1);
2563 		return 0;
2564 	}
2565 
2566 	/* filter bogus IRQs */
2567 	switch (irq) {
2568 	case 0:
2569 	case 2:
2570 	case 8:
2571 	case 13:
2572 		irq = PARPORT_IRQ_NONE;
2573 		break;
2574 
2575 	default: /* do nothing */
2576 		break;
2577 	}
2578 
2579 	/* finally, do the probe with values obtained */
2580 	if (parport_pc_probe_port(port1, port2, irq, dma, &pdev->dev, 0)) {
2581 		printk(KERN_INFO
2582 			"parport_pc: VIA parallel port: io=0x%X", port1);
2583 		if (irq != PARPORT_IRQ_NONE)
2584 			pr_cont(", irq=%d", irq);
2585 		if (dma != PARPORT_DMA_NONE)
2586 			pr_cont(", dma=%d", dma);
2587 		pr_cont("\n");
2588 		return 1;
2589 	}
2590 
2591 	printk(KERN_WARNING "parport_pc: Strange, can't probe VIA parallel port: io=0x%X, irq=%d, dma=%d\n",
2592 		port1, irq, dma);
2593 	return 0;
2594 }
2595 
2596 
2597 enum parport_pc_sio_types {
2598 	sio_via_686a = 0,   /* Via VT82C686A motherboard Super I/O */
2599 	sio_via_8231,	    /* Via VT8231 south bridge integrated Super IO */
2600 	sio_ite_8872,
2601 	last_sio
2602 };
2603 
2604 /* each element directly indexed from enum list, above */
2605 static struct parport_pc_superio {
2606 	int (*probe) (struct pci_dev *pdev, int autoirq, int autodma,
2607 		      const struct parport_pc_via_data *via);
2608 	const struct parport_pc_via_data *via;
2609 } parport_pc_superio_info[] = {
2610 	{ sio_via_probe, &via_686a_data, },
2611 	{ sio_via_probe, &via_8231_data, },
2612 	{ sio_ite_8872_probe, NULL, },
2613 };
2614 
2615 enum parport_pc_pci_cards {
2616 	siig_1p_10x = last_sio,
2617 	siig_2p_10x,
2618 	siig_1p_20x,
2619 	siig_2p_20x,
2620 	lava_parallel,
2621 	lava_parallel_dual_a,
2622 	lava_parallel_dual_b,
2623 	boca_ioppar,
2624 	plx_9050,
2625 	timedia_4006a,
2626 	timedia_4014,
2627 	timedia_4008a,
2628 	timedia_4018,
2629 	timedia_9018a,
2630 	syba_2p_epp,
2631 	syba_1p_ecp,
2632 	titan_010l,
2633 	avlab_1p,
2634 	avlab_2p,
2635 	oxsemi_952,
2636 	oxsemi_954,
2637 	oxsemi_840,
2638 	oxsemi_pcie_pport,
2639 	aks_0100,
2640 	mobility_pp,
2641 	netmos_9705,
2642 	netmos_9715,
2643 	netmos_9755,
2644 	netmos_9805,
2645 	netmos_9815,
2646 	netmos_9901,
2647 	netmos_9865,
2648 	quatech_sppxp100,
2649 	wch_ch382l,
2650 };
2651 
2652 
2653 /* each element directly indexed from enum list, above
2654  * (but offset by last_sio) */
2655 static struct parport_pc_pci {
2656 	int numports;
2657 	struct { /* BAR (base address registers) numbers in the config
2658 		    space header */
2659 		int lo;
2660 		int hi;
2661 		/* -1 if not there, >6 for offset-method (max BAR is 6) */
2662 	} addr[4];
2663 
2664 	/* If set, this is called immediately after pci_enable_device.
2665 	 * If it returns non-zero, no probing will take place and the
2666 	 * ports will not be used. */
2667 	int (*preinit_hook) (struct pci_dev *pdev, int autoirq, int autodma);
2668 
2669 	/* If set, this is called after probing for ports.  If 'failed'
2670 	 * is non-zero we couldn't use any of the ports. */
2671 	void (*postinit_hook) (struct pci_dev *pdev, int failed);
2672 } cards[] = {
2673 	/* siig_1p_10x */		{ 1, { { 2, 3 }, } },
2674 	/* siig_2p_10x */		{ 2, { { 2, 3 }, { 4, 5 }, } },
2675 	/* siig_1p_20x */		{ 1, { { 0, 1 }, } },
2676 	/* siig_2p_20x */		{ 2, { { 0, 1 }, { 2, 3 }, } },
2677 	/* lava_parallel */		{ 1, { { 0, -1 }, } },
2678 	/* lava_parallel_dual_a */	{ 1, { { 0, -1 }, } },
2679 	/* lava_parallel_dual_b */	{ 1, { { 0, -1 }, } },
2680 	/* boca_ioppar */		{ 1, { { 0, -1 }, } },
2681 	/* plx_9050 */			{ 2, { { 4, -1 }, { 5, -1 }, } },
2682 	/* timedia_4006a */             { 1, { { 0, -1 }, } },
2683 	/* timedia_4014  */             { 2, { { 0, -1 }, { 2, -1 }, } },
2684 	/* timedia_4008a */             { 1, { { 0, 1 }, } },
2685 	/* timedia_4018  */             { 2, { { 0, 1 }, { 2, 3 }, } },
2686 	/* timedia_9018a */             { 2, { { 0, 1 }, { 2, 3 }, } },
2687 					/* SYBA uses fixed offsets in
2688 					   a 1K io window */
2689 	/* syba_2p_epp AP138B */	{ 2, { { 0, 0x078 }, { 0, 0x178 }, } },
2690 	/* syba_1p_ecp W83787 */	{ 1, { { 0, 0x078 }, } },
2691 	/* titan_010l */		{ 1, { { 3, -1 }, } },
2692 	/* avlab_1p		*/	{ 1, { { 0, 1}, } },
2693 	/* avlab_2p		*/	{ 2, { { 0, 1}, { 2, 3 },} },
2694 	/* The Oxford Semi cards are unusual: 954 doesn't support ECP,
2695 	 * and 840 locks up if you write 1 to bit 2! */
2696 	/* oxsemi_952 */		{ 1, { { 0, 1 }, } },
2697 	/* oxsemi_954 */		{ 1, { { 0, -1 }, } },
2698 	/* oxsemi_840 */		{ 1, { { 0, 1 }, } },
2699 	/* oxsemi_pcie_pport */		{ 1, { { 0, 1 }, } },
2700 	/* aks_0100 */                  { 1, { { 0, -1 }, } },
2701 	/* mobility_pp */		{ 1, { { 0, 1 }, } },
2702 
2703 	/* The netmos entries below are untested */
2704 	/* netmos_9705 */               { 1, { { 0, -1 }, } },
2705 	/* netmos_9715 */               { 2, { { 0, 1 }, { 2, 3 },} },
2706 	/* netmos_9755 */               { 2, { { 0, 1 }, { 2, 3 },} },
2707 	/* netmos_9805 */		{ 1, { { 0, 1 }, } },
2708 	/* netmos_9815 */		{ 2, { { 0, 1 }, { 2, 3 }, } },
2709 	/* netmos_9901 */               { 1, { { 0, -1 }, } },
2710 	/* netmos_9865 */               { 1, { { 0, -1 }, } },
2711 	/* quatech_sppxp100 */		{ 1, { { 0, 1 }, } },
2712 	/* wch_ch382l */		{ 1, { { 2, -1 }, } },
2713 };
2714 
2715 static const struct pci_device_id parport_pc_pci_tbl[] = {
2716 	/* Super-IO onboard chips */
2717 	{ 0x1106, 0x0686, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sio_via_686a },
2718 	{ 0x1106, 0x8231, PCI_ANY_ID, PCI_ANY_ID, 0, 0, sio_via_8231 },
2719 	{ PCI_VENDOR_ID_ITE, PCI_DEVICE_ID_ITE_8872,
2720 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, sio_ite_8872 },
2721 
2722 	/* PCI cards */
2723 	{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1P_10x,
2724 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_1p_10x },
2725 	{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2P_10x,
2726 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_2p_10x },
2727 	{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_1P_20x,
2728 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_1p_20x },
2729 	{ PCI_VENDOR_ID_SIIG, PCI_DEVICE_ID_SIIG_2P_20x,
2730 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, siig_2p_20x },
2731 	{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_PARALLEL,
2732 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, lava_parallel },
2733 	{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_DUAL_PAR_A,
2734 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, lava_parallel_dual_a },
2735 	{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_DUAL_PAR_B,
2736 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, lava_parallel_dual_b },
2737 	{ PCI_VENDOR_ID_LAVA, PCI_DEVICE_ID_LAVA_BOCA_IOPPAR,
2738 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, boca_ioppar },
2739 	{ PCI_VENDOR_ID_PLX, PCI_DEVICE_ID_PLX_9050,
2740 	  PCI_SUBVENDOR_ID_EXSYS, PCI_SUBDEVICE_ID_EXSYS_4014, 0, 0, plx_9050 },
2741 	/* PCI_VENDOR_ID_TIMEDIA/SUNIX has many differing cards ...*/
2742 	{ 0x1409, 0x7268, 0x1409, 0x0101, 0, 0, timedia_4006a },
2743 	{ 0x1409, 0x7268, 0x1409, 0x0102, 0, 0, timedia_4014 },
2744 	{ 0x1409, 0x7268, 0x1409, 0x0103, 0, 0, timedia_4008a },
2745 	{ 0x1409, 0x7268, 0x1409, 0x0104, 0, 0, timedia_4018 },
2746 	{ 0x1409, 0x7268, 0x1409, 0x9018, 0, 0, timedia_9018a },
2747 	{ PCI_VENDOR_ID_SYBA, PCI_DEVICE_ID_SYBA_2P_EPP,
2748 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, syba_2p_epp },
2749 	{ PCI_VENDOR_ID_SYBA, PCI_DEVICE_ID_SYBA_1P_ECP,
2750 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, syba_1p_ecp },
2751 	{ PCI_VENDOR_ID_TITAN, PCI_DEVICE_ID_TITAN_010L,
2752 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, titan_010l },
2753 	/* PCI_VENDOR_ID_AVLAB/Intek21 has another bunch of cards ...*/
2754 	/* AFAVLAB_TK9902 */
2755 	{ 0x14db, 0x2120, PCI_ANY_ID, PCI_ANY_ID, 0, 0, avlab_1p},
2756 	{ 0x14db, 0x2121, PCI_ANY_ID, PCI_ANY_ID, 0, 0, avlab_2p},
2757 	{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI952PP,
2758 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_952 },
2759 	{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_16PCI954PP,
2760 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_954 },
2761 	{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_12PCI840,
2762 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_840 },
2763 	{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe840,
2764 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport },
2765 	{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe840_G,
2766 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport },
2767 	{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe952_0,
2768 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport },
2769 	{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe952_0_G,
2770 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport },
2771 	{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe952_1,
2772 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport },
2773 	{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe952_1_G,
2774 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport },
2775 	{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe952_1_U,
2776 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport },
2777 	{ PCI_VENDOR_ID_OXSEMI, PCI_DEVICE_ID_OXSEMI_PCIe952_1_GU,
2778 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, oxsemi_pcie_pport },
2779 	{ PCI_VENDOR_ID_AKS, PCI_DEVICE_ID_AKS_ALADDINCARD,
2780 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, aks_0100 },
2781 	{ 0x14f2, 0x0121, PCI_ANY_ID, PCI_ANY_ID, 0, 0, mobility_pp },
2782 	/* NetMos communication controllers */
2783 	{ PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9705,
2784 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9705 },
2785 	{ PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9715,
2786 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9715 },
2787 	{ PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9755,
2788 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9755 },
2789 	{ PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9805,
2790 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9805 },
2791 	{ PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9815,
2792 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, netmos_9815 },
2793 	{ PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9901,
2794 	  0xA000, 0x2000, 0, 0, netmos_9901 },
2795 	{ PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9865,
2796 	  0xA000, 0x1000, 0, 0, netmos_9865 },
2797 	{ PCI_VENDOR_ID_NETMOS, PCI_DEVICE_ID_NETMOS_9865,
2798 	  0xA000, 0x2000, 0, 0, netmos_9865 },
2799 	/* Quatech SPPXP-100 Parallel port PCI ExpressCard */
2800 	{ PCI_VENDOR_ID_QUATECH, PCI_DEVICE_ID_QUATECH_SPPXP_100,
2801 	  PCI_ANY_ID, PCI_ANY_ID, 0, 0, quatech_sppxp100 },
2802 	/* WCH CH382L PCI-E single parallel port card */
2803 	{ 0x1c00, 0x3050, 0x1c00, 0x3050, 0, 0, wch_ch382l },
2804 	{ 0, } /* terminate list */
2805 };
2806 MODULE_DEVICE_TABLE(pci, parport_pc_pci_tbl);
2807 
2808 struct pci_parport_data {
2809 	int num;
2810 	struct parport *ports[2];
2811 };
2812 
parport_pc_pci_probe(struct pci_dev * dev,const struct pci_device_id * id)2813 static int parport_pc_pci_probe(struct pci_dev *dev,
2814 					   const struct pci_device_id *id)
2815 {
2816 	int err, count, n, i = id->driver_data;
2817 	struct pci_parport_data *data;
2818 
2819 	if (i < last_sio)
2820 		/* This is an onboard Super-IO and has already been probed */
2821 		return 0;
2822 
2823 	/* This is a PCI card */
2824 	i -= last_sio;
2825 	count = 0;
2826 	err = pci_enable_device(dev);
2827 	if (err)
2828 		return err;
2829 
2830 	data = kmalloc(sizeof(struct pci_parport_data), GFP_KERNEL);
2831 	if (!data)
2832 		return -ENOMEM;
2833 
2834 	if (cards[i].preinit_hook &&
2835 	    cards[i].preinit_hook(dev, PARPORT_IRQ_NONE, PARPORT_DMA_NONE)) {
2836 		kfree(data);
2837 		return -ENODEV;
2838 	}
2839 
2840 	for (n = 0; n < cards[i].numports; n++) {
2841 		int lo = cards[i].addr[n].lo;
2842 		int hi = cards[i].addr[n].hi;
2843 		int irq;
2844 		unsigned long io_lo, io_hi;
2845 		io_lo = pci_resource_start(dev, lo);
2846 		io_hi = 0;
2847 		if ((hi >= 0) && (hi <= 6))
2848 			io_hi = pci_resource_start(dev, hi);
2849 		else if (hi > 6)
2850 			io_lo += hi; /* Reinterpret the meaning of
2851 					"hi" as an offset (see SYBA
2852 					def.) */
2853 		/* TODO: test if sharing interrupts works */
2854 		irq = dev->irq;
2855 		if (irq == IRQ_NONE) {
2856 			printk(KERN_DEBUG
2857 	"PCI parallel port detected: %04x:%04x, I/O at %#lx(%#lx)\n",
2858 				id->vendor, id->device, io_lo, io_hi);
2859 			irq = PARPORT_IRQ_NONE;
2860 		} else {
2861 			printk(KERN_DEBUG
2862 	"PCI parallel port detected: %04x:%04x, I/O at %#lx(%#lx), IRQ %d\n",
2863 				id->vendor, id->device, io_lo, io_hi, irq);
2864 		}
2865 		data->ports[count] =
2866 			parport_pc_probe_port(io_lo, io_hi, irq,
2867 					       PARPORT_DMA_NONE, &dev->dev,
2868 					       IRQF_SHARED);
2869 		if (data->ports[count])
2870 			count++;
2871 	}
2872 
2873 	data->num = count;
2874 
2875 	if (cards[i].postinit_hook)
2876 		cards[i].postinit_hook(dev, count == 0);
2877 
2878 	if (count) {
2879 		pci_set_drvdata(dev, data);
2880 		return 0;
2881 	}
2882 
2883 	kfree(data);
2884 
2885 	return -ENODEV;
2886 }
2887 
parport_pc_pci_remove(struct pci_dev * dev)2888 static void parport_pc_pci_remove(struct pci_dev *dev)
2889 {
2890 	struct pci_parport_data *data = pci_get_drvdata(dev);
2891 	int i;
2892 
2893 	if (data) {
2894 		for (i = data->num - 1; i >= 0; i--)
2895 			parport_pc_unregister_port(data->ports[i]);
2896 
2897 		kfree(data);
2898 	}
2899 }
2900 
2901 static struct pci_driver parport_pc_pci_driver = {
2902 	.name		= "parport_pc",
2903 	.id_table	= parport_pc_pci_tbl,
2904 	.probe		= parport_pc_pci_probe,
2905 	.remove		= parport_pc_pci_remove,
2906 };
2907 
parport_pc_init_superio(int autoirq,int autodma)2908 static int __init parport_pc_init_superio(int autoirq, int autodma)
2909 {
2910 	const struct pci_device_id *id;
2911 	struct pci_dev *pdev = NULL;
2912 	int ret = 0;
2913 
2914 	for_each_pci_dev(pdev) {
2915 		id = pci_match_id(parport_pc_pci_tbl, pdev);
2916 		if (id == NULL || id->driver_data >= last_sio)
2917 			continue;
2918 
2919 		if (parport_pc_superio_info[id->driver_data].probe(
2920 			pdev, autoirq, autodma,
2921 			parport_pc_superio_info[id->driver_data].via)) {
2922 			ret++;
2923 		}
2924 	}
2925 
2926 	return ret; /* number of devices found */
2927 }
2928 #else
2929 static struct pci_driver parport_pc_pci_driver;
parport_pc_init_superio(int autoirq,int autodma)2930 static int __init parport_pc_init_superio(int autoirq, int autodma)
2931 {
2932 	return 0;
2933 }
2934 #endif /* CONFIG_PCI */
2935 
2936 #ifdef CONFIG_PNP
2937 
2938 static const struct pnp_device_id parport_pc_pnp_tbl[] = {
2939 	/* Standard LPT Printer Port */
2940 	{.id = "PNP0400", .driver_data = 0},
2941 	/* ECP Printer Port */
2942 	{.id = "PNP0401", .driver_data = 0},
2943 	{ }
2944 };
2945 
2946 MODULE_DEVICE_TABLE(pnp, parport_pc_pnp_tbl);
2947 
parport_pc_pnp_probe(struct pnp_dev * dev,const struct pnp_device_id * id)2948 static int parport_pc_pnp_probe(struct pnp_dev *dev,
2949 						const struct pnp_device_id *id)
2950 {
2951 	struct parport *pdata;
2952 	unsigned long io_lo, io_hi;
2953 	int dma, irq;
2954 
2955 	if (pnp_port_valid(dev, 0) &&
2956 		!(pnp_port_flags(dev, 0) & IORESOURCE_DISABLED)) {
2957 		io_lo = pnp_port_start(dev, 0);
2958 	} else
2959 		return -EINVAL;
2960 
2961 	if (pnp_port_valid(dev, 1) &&
2962 		!(pnp_port_flags(dev, 1) & IORESOURCE_DISABLED)) {
2963 		io_hi = pnp_port_start(dev, 1);
2964 	} else
2965 		io_hi = 0;
2966 
2967 	if (pnp_irq_valid(dev, 0) &&
2968 		!(pnp_irq_flags(dev, 0) & IORESOURCE_DISABLED)) {
2969 		irq = pnp_irq(dev, 0);
2970 	} else
2971 		irq = PARPORT_IRQ_NONE;
2972 
2973 	if (pnp_dma_valid(dev, 0) &&
2974 		!(pnp_dma_flags(dev, 0) & IORESOURCE_DISABLED)) {
2975 		dma = pnp_dma(dev, 0);
2976 	} else
2977 		dma = PARPORT_DMA_NONE;
2978 
2979 	dev_info(&dev->dev, "reported by %s\n", dev->protocol->name);
2980 	pdata = parport_pc_probe_port(io_lo, io_hi, irq, dma, &dev->dev, 0);
2981 	if (pdata == NULL)
2982 		return -ENODEV;
2983 
2984 	pnp_set_drvdata(dev, pdata);
2985 	return 0;
2986 }
2987 
parport_pc_pnp_remove(struct pnp_dev * dev)2988 static void parport_pc_pnp_remove(struct pnp_dev *dev)
2989 {
2990 	struct parport *pdata = (struct parport *)pnp_get_drvdata(dev);
2991 	if (!pdata)
2992 		return;
2993 
2994 	parport_pc_unregister_port(pdata);
2995 }
2996 
2997 /* we only need the pnp layer to activate the device, at least for now */
2998 static struct pnp_driver parport_pc_pnp_driver = {
2999 	.name		= "parport_pc",
3000 	.id_table	= parport_pc_pnp_tbl,
3001 	.probe		= parport_pc_pnp_probe,
3002 	.remove		= parport_pc_pnp_remove,
3003 };
3004 
3005 #else
3006 static struct pnp_driver parport_pc_pnp_driver;
3007 #endif /* CONFIG_PNP */
3008 
parport_pc_platform_probe(struct platform_device * pdev)3009 static int parport_pc_platform_probe(struct platform_device *pdev)
3010 {
3011 	/* Always succeed, the actual probing is done in
3012 	 * parport_pc_probe_port(). */
3013 	return 0;
3014 }
3015 
3016 static struct platform_driver parport_pc_platform_driver = {
3017 	.driver = {
3018 		.name	= "parport_pc",
3019 	},
3020 	.probe		= parport_pc_platform_probe,
3021 };
3022 
3023 /* This is called by parport_pc_find_nonpci_ports (in asm/parport.h) */
3024 static int __attribute__((unused))
parport_pc_find_isa_ports(int autoirq,int autodma)3025 parport_pc_find_isa_ports(int autoirq, int autodma)
3026 {
3027 	int count = 0;
3028 
3029 	if (parport_pc_probe_port(0x3bc, 0x7bc, autoirq, autodma, NULL, 0))
3030 		count++;
3031 	if (parport_pc_probe_port(0x378, 0x778, autoirq, autodma, NULL, 0))
3032 		count++;
3033 	if (parport_pc_probe_port(0x278, 0x678, autoirq, autodma, NULL, 0))
3034 		count++;
3035 
3036 	return count;
3037 }
3038 
3039 /* This function is called by parport_pc_init if the user didn't
3040  * specify any ports to probe.  Its job is to find some ports.  Order
3041  * is important here -- we want ISA ports to be registered first,
3042  * followed by PCI cards (for least surprise), but before that we want
3043  * to do chipset-specific tests for some onboard ports that we know
3044  * about.
3045  *
3046  * autoirq is PARPORT_IRQ_NONE, PARPORT_IRQ_AUTO, or PARPORT_IRQ_PROBEONLY
3047  * autodma is PARPORT_DMA_NONE or PARPORT_DMA_AUTO
3048  */
parport_pc_find_ports(int autoirq,int autodma)3049 static void __init parport_pc_find_ports(int autoirq, int autodma)
3050 {
3051 	int count = 0, err;
3052 
3053 #ifdef CONFIG_PARPORT_PC_SUPERIO
3054 	detect_and_report_it87();
3055 	detect_and_report_winbond();
3056 	detect_and_report_smsc();
3057 #endif
3058 
3059 	/* Onboard SuperIO chipsets that show themselves on the PCI bus. */
3060 	count += parport_pc_init_superio(autoirq, autodma);
3061 
3062 	/* PnP ports, skip detection if SuperIO already found them */
3063 	if (!count) {
3064 		err = pnp_register_driver(&parport_pc_pnp_driver);
3065 		if (!err)
3066 			pnp_registered_parport = 1;
3067 	}
3068 
3069 	/* ISA ports and whatever (see asm/parport.h). */
3070 	parport_pc_find_nonpci_ports(autoirq, autodma);
3071 
3072 	err = pci_register_driver(&parport_pc_pci_driver);
3073 	if (!err)
3074 		pci_registered_parport = 1;
3075 }
3076 
3077 /*
3078  *	Piles of crap below pretend to be a parser for module and kernel
3079  *	parameters.  Say "thank you" to whoever had come up with that
3080  *	syntax and keep in mind that code below is a cleaned up version.
3081  */
3082 
3083 static int __initdata io[PARPORT_PC_MAX_PORTS+1] = {
3084 	[0 ... PARPORT_PC_MAX_PORTS] = 0
3085 };
3086 static int __initdata io_hi[PARPORT_PC_MAX_PORTS+1] = {
3087 	[0 ... PARPORT_PC_MAX_PORTS] = PARPORT_IOHI_AUTO
3088 };
3089 static int __initdata dmaval[PARPORT_PC_MAX_PORTS] = {
3090 	[0 ... PARPORT_PC_MAX_PORTS-1] = PARPORT_DMA_NONE
3091 };
3092 static int __initdata irqval[PARPORT_PC_MAX_PORTS] = {
3093 	[0 ... PARPORT_PC_MAX_PORTS-1] = PARPORT_IRQ_PROBEONLY
3094 };
3095 
parport_parse_param(const char * s,int * val,int automatic,int none,int nofifo)3096 static int __init parport_parse_param(const char *s, int *val,
3097 				int automatic, int none, int nofifo)
3098 {
3099 	if (!s)
3100 		return 0;
3101 	if (!strncmp(s, "auto", 4))
3102 		*val = automatic;
3103 	else if (!strncmp(s, "none", 4))
3104 		*val = none;
3105 	else if (nofifo && !strncmp(s, "nofifo", 6))
3106 		*val = nofifo;
3107 	else {
3108 		char *ep;
3109 		unsigned long r = simple_strtoul(s, &ep, 0);
3110 		if (ep != s)
3111 			*val = r;
3112 		else {
3113 			printk(KERN_ERR "parport: bad specifier `%s'\n", s);
3114 			return -1;
3115 		}
3116 	}
3117 	return 0;
3118 }
3119 
parport_parse_irq(const char * irqstr,int * val)3120 static int __init parport_parse_irq(const char *irqstr, int *val)
3121 {
3122 	return parport_parse_param(irqstr, val, PARPORT_IRQ_AUTO,
3123 				     PARPORT_IRQ_NONE, 0);
3124 }
3125 
parport_parse_dma(const char * dmastr,int * val)3126 static int __init parport_parse_dma(const char *dmastr, int *val)
3127 {
3128 	return parport_parse_param(dmastr, val, PARPORT_DMA_AUTO,
3129 				     PARPORT_DMA_NONE, PARPORT_DMA_NOFIFO);
3130 }
3131 
3132 #ifdef CONFIG_PCI
parport_init_mode_setup(char * str)3133 static int __init parport_init_mode_setup(char *str)
3134 {
3135 	printk(KERN_DEBUG
3136 	     "parport_pc.c: Specified parameter parport_init_mode=%s\n", str);
3137 
3138 	if (!strcmp(str, "spp"))
3139 		parport_init_mode = 1;
3140 	if (!strcmp(str, "ps2"))
3141 		parport_init_mode = 2;
3142 	if (!strcmp(str, "epp"))
3143 		parport_init_mode = 3;
3144 	if (!strcmp(str, "ecp"))
3145 		parport_init_mode = 4;
3146 	if (!strcmp(str, "ecpepp"))
3147 		parport_init_mode = 5;
3148 	return 1;
3149 }
3150 #endif
3151 
3152 #ifdef MODULE
3153 static char *irq[PARPORT_PC_MAX_PORTS];
3154 static char *dma[PARPORT_PC_MAX_PORTS];
3155 
3156 MODULE_PARM_DESC(io, "Base I/O address (SPP regs)");
3157 module_param_hw_array(io, int, ioport, NULL, 0);
3158 MODULE_PARM_DESC(io_hi, "Base I/O address (ECR)");
3159 module_param_hw_array(io_hi, int, ioport, NULL, 0);
3160 MODULE_PARM_DESC(irq, "IRQ line");
3161 module_param_hw_array(irq, charp, irq, NULL, 0);
3162 MODULE_PARM_DESC(dma, "DMA channel");
3163 module_param_hw_array(dma, charp, dma, NULL, 0);
3164 #if defined(CONFIG_PARPORT_PC_SUPERIO) || \
3165        (defined(CONFIG_PARPORT_1284) && defined(CONFIG_PARPORT_PC_FIFO))
3166 MODULE_PARM_DESC(verbose_probing, "Log chit-chat during initialisation");
3167 module_param(verbose_probing, int, 0644);
3168 #endif
3169 #ifdef CONFIG_PCI
3170 static char *init_mode;
3171 MODULE_PARM_DESC(init_mode,
3172 	"Initialise mode for VIA VT8231 port (spp, ps2, epp, ecp or ecpepp)");
3173 module_param(init_mode, charp, 0);
3174 #endif
3175 
parse_parport_params(void)3176 static int __init parse_parport_params(void)
3177 {
3178 	unsigned int i;
3179 	int val;
3180 
3181 #ifdef CONFIG_PCI
3182 	if (init_mode)
3183 		parport_init_mode_setup(init_mode);
3184 #endif
3185 
3186 	for (i = 0; i < PARPORT_PC_MAX_PORTS && io[i]; i++) {
3187 		if (parport_parse_irq(irq[i], &val))
3188 			return 1;
3189 		irqval[i] = val;
3190 		if (parport_parse_dma(dma[i], &val))
3191 			return 1;
3192 		dmaval[i] = val;
3193 	}
3194 	if (!io[0]) {
3195 		/* The user can make us use any IRQs or DMAs we find. */
3196 		if (irq[0] && !parport_parse_irq(irq[0], &val))
3197 			switch (val) {
3198 			case PARPORT_IRQ_NONE:
3199 			case PARPORT_IRQ_AUTO:
3200 				irqval[0] = val;
3201 				break;
3202 			default:
3203 				printk(KERN_WARNING
3204 					"parport_pc: irq specified "
3205 					"without base address.  Use 'io=' "
3206 					"to specify one\n");
3207 			}
3208 
3209 		if (dma[0] && !parport_parse_dma(dma[0], &val))
3210 			switch (val) {
3211 			case PARPORT_DMA_NONE:
3212 			case PARPORT_DMA_AUTO:
3213 				dmaval[0] = val;
3214 				break;
3215 			default:
3216 				printk(KERN_WARNING
3217 					"parport_pc: dma specified "
3218 					"without base address.  Use 'io=' "
3219 					"to specify one\n");
3220 			}
3221 	}
3222 	return 0;
3223 }
3224 
3225 #else
3226 
3227 static int parport_setup_ptr __initdata;
3228 
3229 /*
3230  * Acceptable parameters:
3231  *
3232  * parport=0
3233  * parport=auto
3234  * parport=0xBASE[,IRQ[,DMA]]
3235  *
3236  * IRQ/DMA may be numeric or 'auto' or 'none'
3237  */
parport_setup(char * str)3238 static int __init parport_setup(char *str)
3239 {
3240 	char *endptr;
3241 	char *sep;
3242 	int val;
3243 
3244 	if (!str || !*str || (*str == '0' && !*(str+1))) {
3245 		/* Disable parport if "parport=0" in cmdline */
3246 		io[0] = PARPORT_DISABLE;
3247 		return 1;
3248 	}
3249 
3250 	if (!strncmp(str, "auto", 4)) {
3251 		irqval[0] = PARPORT_IRQ_AUTO;
3252 		dmaval[0] = PARPORT_DMA_AUTO;
3253 		return 1;
3254 	}
3255 
3256 	val = simple_strtoul(str, &endptr, 0);
3257 	if (endptr == str) {
3258 		printk(KERN_WARNING "parport=%s not understood\n", str);
3259 		return 1;
3260 	}
3261 
3262 	if (parport_setup_ptr == PARPORT_PC_MAX_PORTS) {
3263 		printk(KERN_ERR "parport=%s ignored, too many ports\n", str);
3264 		return 1;
3265 	}
3266 
3267 	io[parport_setup_ptr] = val;
3268 	irqval[parport_setup_ptr] = PARPORT_IRQ_NONE;
3269 	dmaval[parport_setup_ptr] = PARPORT_DMA_NONE;
3270 
3271 	sep = strchr(str, ',');
3272 	if (sep++) {
3273 		if (parport_parse_irq(sep, &val))
3274 			return 1;
3275 		irqval[parport_setup_ptr] = val;
3276 		sep = strchr(sep, ',');
3277 		if (sep++) {
3278 			if (parport_parse_dma(sep, &val))
3279 				return 1;
3280 			dmaval[parport_setup_ptr] = val;
3281 		}
3282 	}
3283 	parport_setup_ptr++;
3284 	return 1;
3285 }
3286 
parse_parport_params(void)3287 static int __init parse_parport_params(void)
3288 {
3289 	return io[0] == PARPORT_DISABLE;
3290 }
3291 
3292 __setup("parport=", parport_setup);
3293 
3294 /*
3295  * Acceptable parameters:
3296  *
3297  * parport_init_mode=[spp|ps2|epp|ecp|ecpepp]
3298  */
3299 #ifdef CONFIG_PCI
3300 __setup("parport_init_mode=", parport_init_mode_setup);
3301 #endif
3302 #endif
3303 
3304 /* "Parser" ends here */
3305 
parport_pc_init(void)3306 static int __init parport_pc_init(void)
3307 {
3308 	int err;
3309 
3310 	if (parse_parport_params())
3311 		return -EINVAL;
3312 
3313 	err = platform_driver_register(&parport_pc_platform_driver);
3314 	if (err)
3315 		return err;
3316 
3317 	if (io[0]) {
3318 		int i;
3319 		/* Only probe the ports we were given. */
3320 		user_specified = 1;
3321 		for (i = 0; i < PARPORT_PC_MAX_PORTS; i++) {
3322 			if (!io[i])
3323 				break;
3324 			if (io_hi[i] == PARPORT_IOHI_AUTO)
3325 				io_hi[i] = 0x400 + io[i];
3326 			parport_pc_probe_port(io[i], io_hi[i],
3327 					irqval[i], dmaval[i], NULL, 0);
3328 		}
3329 	} else
3330 		parport_pc_find_ports(irqval[0], dmaval[0]);
3331 
3332 	return 0;
3333 }
3334 
parport_pc_exit(void)3335 static void __exit parport_pc_exit(void)
3336 {
3337 	if (pci_registered_parport)
3338 		pci_unregister_driver(&parport_pc_pci_driver);
3339 	if (pnp_registered_parport)
3340 		pnp_unregister_driver(&parport_pc_pnp_driver);
3341 	platform_driver_unregister(&parport_pc_platform_driver);
3342 
3343 	while (!list_empty(&ports_list)) {
3344 		struct parport_pc_private *priv;
3345 		struct parport *port;
3346 		struct device *dev;
3347 		priv = list_entry(ports_list.next,
3348 				  struct parport_pc_private, list);
3349 		port = priv->port;
3350 		dev = port->dev;
3351 		parport_pc_unregister_port(port);
3352 		if (dev && dev->bus == &platform_bus_type)
3353 			platform_device_unregister(to_platform_device(dev));
3354 	}
3355 }
3356 
3357 MODULE_AUTHOR("Phil Blundell, Tim Waugh, others");
3358 MODULE_DESCRIPTION("PC-style parallel port driver");
3359 MODULE_LICENSE("GPL");
3360 module_init(parport_pc_init)
3361 module_exit(parport_pc_exit)
3362