1 2menu "Passive cards" 3 4config ISDN_DRV_HISAX 5 tristate "HiSax SiemensChipSet driver support" 6 select CRC_CCITT 7 ---help--- 8 This is a driver supporting the Siemens chipset on various 9 ISDN-cards (like AVM A1, Elsa ISDN cards, Teles S0-16.0, Teles 10 S0-16.3, Teles S0-8, Teles/Creatix PnP, ITK micro ix1 and many 11 compatibles). 12 13 HiSax is just the name of this driver, not the name of any hardware. 14 15 If you have a card with such a chipset, you should say Y here and 16 also to the configuration option of the driver for your particular 17 card, below. 18 19if ISDN_DRV_HISAX 20 21comment "D-channel protocol features" 22 23config HISAX_EURO 24 bool "HiSax Support for EURO/DSS1" 25 help 26 Say Y or N according to the D-channel protocol which your local 27 telephone service company provides. 28 29 The call control protocol E-DSS1 is used in most European countries. 30 If unsure, say Y. 31 32config DE_AOC 33 bool "Support for german chargeinfo" 34 depends on HISAX_EURO 35 help 36 If you want that the HiSax hardware driver sends messages to the 37 upper level of the isdn code on each AOCD (Advice Of Charge, During 38 the call -- transmission of the fee information during a call) and 39 on each AOCE (Advice Of Charge, at the End of the call -- 40 transmission of fee information at the end of the call), say Y here. 41 This works only in Germany. 42 43config HISAX_NO_SENDCOMPLETE 44 bool "Disable sending complete" 45 depends on HISAX_EURO 46 help 47 If you have trouble with some ugly exchanges or you live in 48 Australia select this option. 49 50config HISAX_NO_LLC 51 bool "Disable sending low layer compatibility" 52 depends on HISAX_EURO 53 help 54 If you have trouble with some ugly exchanges try to select this 55 option. 56 57config HISAX_NO_KEYPAD 58 bool "Disable keypad protocol option" 59 depends on HISAX_EURO 60 help 61 If you like to send special dial strings including * or # without 62 using the keypad protocol, select this option. 63 64config HISAX_1TR6 65 bool "HiSax Support for german 1TR6" 66 help 67 Say Y or N according to the D-channel protocol which your local 68 telephone service company provides. 69 70 1TR6 is an old call control protocol which was used in Germany 71 before E-DSS1 was established. Nowadays, all new lines in Germany 72 use E-DSS1. 73 74config HISAX_NI1 75 bool "HiSax Support for US NI1" 76 help 77 Enable this if you like to use ISDN in US on a NI1 basic rate 78 interface. 79 80config HISAX_MAX_CARDS 81 int "Maximum number of cards supported by HiSax" 82 default "8" 83 help 84 This option allows you to specify the maximum number of cards which 85 the HiSax driver will be able to handle. 86 87comment "HiSax supported cards" 88 89config HISAX_16_0 90 bool "Teles 16.0/8.0" 91 depends on ISA 92 help 93 This enables HiSax support for the Teles ISDN-cards S0-16.0, S0-8 94 and many compatibles. 95 96 See <file:Documentation/isdn/README.HiSax> on how to configure it 97 using the different cards, a different D-channel protocol, or 98 non-standard IRQ/port/shmem settings. 99 100config HISAX_16_3 101 bool "Teles 16.3 or PNP or PCMCIA" 102 help 103 This enables HiSax support for the Teles ISDN-cards S0-16.3 the 104 Teles/Creatix PnP and the Teles PCMCIA. 105 106 See <file:Documentation/isdn/README.HiSax> on how to configure it 107 using the different cards, a different D-channel protocol, or 108 non-standard IRQ/port settings. 109 110config HISAX_TELESPCI 111 bool "Teles PCI" 112 depends on PCI && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || (XTENSA && !CPU_LITTLE_ENDIAN))) 113 help 114 This enables HiSax support for the Teles PCI. 115 See <file:Documentation/isdn/README.HiSax> on how to configure it. 116 117config HISAX_S0BOX 118 bool "Teles S0Box" 119 help 120 This enables HiSax support for the Teles/Creatix parallel port 121 S0BOX. See <file:Documentation/isdn/README.HiSax> on how to 122 configure it. 123 124config HISAX_AVM_A1 125 bool "AVM A1 (Fritz)" 126 depends on ISA 127 help 128 This enables HiSax support for the AVM A1 (aka "Fritz"). 129 130 See <file:Documentation/isdn/README.HiSax> on how to configure it 131 using the different cards, a different D-channel protocol, or 132 non-standard IRQ/port settings. 133 134config HISAX_FRITZPCI 135 bool "AVM PnP/PCI (Fritz!PnP/PCI)" 136 depends on BROKEN || !PPC64 137 help 138 This enables HiSax support for the AVM "Fritz!PnP" and "Fritz!PCI". 139 See <file:Documentation/isdn/README.HiSax> on how to configure it. 140 141config HISAX_AVM_A1_PCMCIA 142 bool "AVM A1 PCMCIA (Fritz)" 143 help 144 This enables HiSax support for the AVM A1 "Fritz!PCMCIA"). 145 See <file:Documentation/isdn/README.HiSax> on how to configure it. 146 147config HISAX_ELSA 148 bool "Elsa cards" 149 help 150 This enables HiSax support for the Elsa Mircolink ISA cards, for the 151 Elsa Quickstep series cards and Elsa PCMCIA. 152 153 See <file:Documentation/isdn/README.HiSax> on how to configure it 154 using the different cards, a different D-channel protocol, or 155 non-standard IRQ/port settings. 156 157config HISAX_IX1MICROR2 158 bool "ITK ix1-micro Revision 2" 159 depends on ISA 160 help 161 This enables HiSax support for the ITK ix1-micro Revision 2 card. 162 163 See <file:Documentation/isdn/README.HiSax> on how to configure it 164 using the different cards, a different D-channel protocol, or 165 non-standard IRQ/port settings. 166 167config HISAX_DIEHLDIVA 168 bool "Eicon.Diehl Diva cards" 169 help 170 This enables HiSax support for the Eicon.Diehl Diva none PRO 171 versions passive ISDN cards. 172 173 See <file:Documentation/isdn/README.HiSax> on how to configure it 174 using the different cards, a different D-channel protocol, or 175 non-standard IRQ/port settings. 176 177config HISAX_ASUSCOM 178 bool "ASUSCOM ISA cards" 179 depends on ISA 180 help 181 This enables HiSax support for the AsusCom and their OEM versions 182 passive ISDN ISA cards. 183 184 See <file:Documentation/isdn/README.HiSax> on how to configure it 185 using the different cards, a different D-channel protocol, or 186 non-standard IRQ/port settings. 187 188config HISAX_TELEINT 189 bool "TELEINT cards" 190 depends on ISA 191 help 192 This enables HiSax support for the TELEINT SA1 semiactiv ISDN card. 193 194 See <file:Documentation/isdn/README.HiSax> on how to configure it 195 using the different cards, a different D-channel protocol, or 196 non-standard IRQ/port settings. 197 198config HISAX_HFCS 199 bool "HFC-S based cards" 200 depends on ISA 201 help 202 This enables HiSax support for the HFC-S 2BDS0 based cards, like 203 teles 16.3c. 204 205 See <file:Documentation/isdn/README.HiSax> on how to configure it 206 using the different cards, a different D-channel protocol, or 207 non-standard IRQ/port settings. 208 209config HISAX_SEDLBAUER 210 bool "Sedlbauer cards" 211 help 212 This enables HiSax support for the Sedlbauer passive ISDN cards. 213 214 See <file:Documentation/isdn/README.HiSax> on how to configure it 215 using the different cards, a different D-channel protocol, or 216 non-standard IRQ/port settings. 217 218config HISAX_SPORTSTER 219 bool "USR Sportster internal TA" 220 depends on ISA 221 help 222 This enables HiSax support for the USR Sportster internal TA card. 223 224 See <file:Documentation/isdn/README.HiSax> on how to configure it 225 using a different D-channel protocol, or non-standard IRQ/port 226 settings. 227 228config HISAX_MIC 229 bool "MIC card" 230 depends on ISA 231 help 232 This enables HiSax support for the ITH MIC card. 233 234 See <file:Documentation/isdn/README.HiSax> on how to configure it 235 using a different D-channel protocol, or non-standard IRQ/port 236 settings. 237 238config HISAX_NETJET 239 bool "NETjet card" 240 depends on PCI && (BROKEN || !(PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || (XTENSA && !CPU_LITTLE_ENDIAN) || MICROBLAZE)) 241 depends on VIRT_TO_BUS 242 help 243 This enables HiSax support for the NetJet from Traverse 244 Technologies. 245 246 See <file:Documentation/isdn/README.HiSax> on how to configure it 247 using a different D-channel protocol, or non-standard IRQ/port 248 settings. 249 250config HISAX_NETJET_U 251 bool "NETspider U card" 252 depends on PCI && (BROKEN || !(PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || (XTENSA && !CPU_LITTLE_ENDIAN) || MICROBLAZE)) 253 depends on VIRT_TO_BUS 254 help 255 This enables HiSax support for the Netspider U interface ISDN card 256 from Traverse Technologies. 257 See <file:Documentation/isdn/README.HiSax> on how to configure it 258 using a different D-channel protocol, or non-standard IRQ/port 259 settings. 260 261config HISAX_NICCY 262 bool "Niccy PnP/PCI card" 263 help 264 This enables HiSax support for the Dr. Neuhaus Niccy PnP or PCI. 265 266 See <file:Documentation/isdn/README.HiSax> on how to configure it 267 using a different D-channel protocol, or non-standard IRQ/port 268 settings. 269 270config HISAX_ISURF 271 bool "Siemens I-Surf card" 272 depends on ISA 273 help 274 This enables HiSax support for the Siemens I-Talk/I-Surf card with 275 ISAR chip. 276 See <file:Documentation/isdn/README.HiSax> on how to configure it 277 using a different D-channel protocol, or non-standard IRQ/port 278 settings. 279 280config HISAX_HSTSAPHIR 281 bool "HST Saphir card" 282 depends on ISA 283 help 284 This enables HiSax support for the HST Saphir card. 285 286 See <file:Documentation/isdn/README.HiSax> on how to configure it 287 using a different D-channel protocol, or non-standard IRQ/port 288 settings. 289 290config HISAX_BKM_A4T 291 bool "Telekom A4T card" 292 depends on PCI 293 help 294 This enables HiSax support for the Telekom A4T card. 295 296 See <file:Documentation/isdn/README.HiSax> on how to configure it 297 using a different D-channel protocol, or non-standard IRQ/port 298 settings. 299 300config HISAX_SCT_QUADRO 301 bool "Scitel Quadro card" 302 depends on PCI 303 help 304 This enables HiSax support for the Scitel Quadro card. 305 306 See <file:Documentation/isdn/README.HiSax> on how to configure it 307 using a different D-channel protocol, or non-standard IRQ/port 308 settings. 309 310config HISAX_GAZEL 311 bool "Gazel cards" 312 help 313 This enables HiSax support for the Gazel cards. 314 315 See <file:Documentation/isdn/README.HiSax> on how to configure it 316 using a different D-channel protocol, or non-standard IRQ/port 317 settings. 318 319config HISAX_HFC_PCI 320 bool "HFC PCI-Bus cards" 321 depends on PCI && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || (XTENSA && !CPU_LITTLE_ENDIAN))) 322 help 323 This enables HiSax support for the HFC-S PCI 2BDS0 based cards. 324 325 For more information see under 326 <file:Documentation/isdn/README.hfc-pci>. 327 328config HISAX_W6692 329 bool "Winbond W6692 based cards" 330 depends on PCI 331 help 332 This enables HiSax support for Winbond W6692 based PCI ISDN cards. 333 334 See <file:Documentation/isdn/README.HiSax> on how to configure it 335 using a different D-channel protocol, or non-standard IRQ/port 336 settings. 337 338config HISAX_HFC_SX 339 bool "HFC-S+, HFC-SP, HFC-PCMCIA cards" 340 help 341 This enables HiSax support for the HFC-S+, HFC-SP and HFC-PCMCIA 342 cards. This code is not finished yet. 343 344config HISAX_ENTERNOW_PCI 345 bool "Formula-n enter:now PCI card" 346 depends on HISAX_NETJET && PCI && (BROKEN || !(SPARC || PPC || PARISC || M68K || (MIPS && !CPU_LITTLE_ENDIAN) || (XTENSA && !CPU_LITTLE_ENDIAN))) 347 help 348 This enables HiSax support for the Formula-n enter:now PCI 349 ISDN card. 350 351config HISAX_DEBUG 352 bool "HiSax debugging" 353 help 354 This enables debugging code in the new-style HiSax drivers, i.e. 355 the ST5481 USB driver currently. 356 If in doubt, say yes. 357 358comment "HiSax PCMCIA card service modules" 359 360config HISAX_SEDLBAUER_CS 361 tristate "Sedlbauer PCMCIA cards" 362 depends on PCMCIA && HISAX_SEDLBAUER 363 help 364 This enables the PCMCIA client driver for the Sedlbauer Speed Star 365 and Speed Star II cards. 366 367config HISAX_ELSA_CS 368 tristate "ELSA PCMCIA MicroLink cards" 369 depends on PCMCIA && HISAX_ELSA 370 help 371 This enables the PCMCIA client driver for the Elsa PCMCIA MicroLink 372 card. 373 374config HISAX_AVM_A1_CS 375 tristate "AVM A1 PCMCIA cards" 376 depends on PCMCIA && ISDN_DRV_HISAX 377 help 378 This enables the PCMCIA client driver for the AVM A1 / Fritz!Card 379 PCMCIA cards. 380 381config HISAX_TELES_CS 382 tristate "TELES PCMCIA cards" 383 depends on PCMCIA && HISAX_16_3 384 help 385 This enables the PCMCIA client driver for the Teles PCMCIA cards. 386 387comment "HiSax sub driver modules" 388 389config HISAX_ST5481 390 tristate "ST5481 USB ISDN modem" 391 depends on USB 392 select ISDN_HDLC 393 select CRC_CCITT 394 select BITREVERSE 395 help 396 This enables the driver for ST5481 based USB ISDN adapters, 397 e.g. the BeWan Gazel 128 USB 398 399config HISAX_HFCUSB 400 tristate "HFC USB based ISDN modems" 401 depends on USB 402 help 403 This enables the driver for HFC USB based ISDN modems. 404 405config HISAX_HFC4S8S 406 tristate "HFC-4S/8S based ISDN cards" 407 help 408 This enables the driver for HFC-4S/8S based ISDN cards. 409 410config HISAX_FRITZ_PCIPNP 411 tristate "AVM Fritz!Card PCI/PCIv2/PnP support" 412 depends on PCI 413 help 414 This enables the driver for the AVM Fritz!Card PCI, 415 Fritz!Card PCI v2 and Fritz!Card PnP. 416 (the latter also needs you to select "ISA Plug and Play support" 417 from the menu "Plug and Play configuration") 418 419endif 420 421endmenu 422 423