1 /*
2  *  Shared Transport Header file
3  *	To be included by the protocol stack drivers for
4  *	Texas Instruments BT,FM and GPS combo chip drivers
5  *	and also serves the sub-modules of the shared transport driver.
6  *
7  *  Copyright (C) 2009-2010 Texas Instruments
8  *  Author: Pavan Savoy <pavan_savoy@ti.com>
9  *
10  *  This program is free software; you can redistribute it and/or modify
11  *  it under the terms of the GNU General Public License version 2 as
12  *  published by the Free Software Foundation.
13  *
14  *  This program is distributed in the hope that it will be useful,
15  *  but WITHOUT ANY WARRANTY; without even the implied warranty of
16  *  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
17  *  GNU General Public License for more details.
18  *
19  *  You should have received a copy of the GNU General Public License
20  *  along with this program; if not, write to the Free Software
21  *  Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
22  *
23  */
24 
25 #ifndef TI_WILINK_ST_H
26 #define TI_WILINK_ST_H
27 
28 #include <linux/skbuff.h>
29 
30 /**
31  * enum proto-type - The protocol on WiLink chips which share a
32  *	common physical interface like UART.
33  */
34 enum proto_type {
35 	ST_BT,
36 	ST_FM,
37 	ST_GPS,
38 	ST_MAX_CHANNELS = 16,
39 };
40 
41 /**
42  * struct st_proto_s - Per Protocol structure from BT/FM/GPS to ST
43  * @type: type of the protocol being registered among the
44  *	available proto_type(BT, FM, GPS the protocol which share TTY).
45  * @recv: the receiver callback pointing to a function in the
46  *	protocol drivers called by the ST driver upon receiving
47  *	relevant data.
48  * @match_packet: reserved for future use, to make ST more generic
49  * @reg_complete_cb: callback handler pointing to a function in protocol
50  *	handler called by ST when the pending registrations are complete.
51  *	The registrations are marked pending, in situations when fw
52  *	download is in progress.
53  * @write: pointer to function in ST provided to protocol drivers from ST,
54  *	to be made use when protocol drivers have data to send to TTY.
55  * @priv_data: privdate data holder for the protocol drivers, sent
56  *	from the protocol drivers during registration, and sent back on
57  *	reg_complete_cb and recv.
58  * @chnl_id: channel id the protocol driver is interested in, the channel
59  *	id is nothing but the 1st byte of the packet in UART frame.
60  * @max_frame_size: size of the largest frame the protocol can receive.
61  * @hdr_len: length of the header structure of the protocol.
62  * @offset_len_in_hdr: this provides the offset of the length field in the
63  *	header structure of the protocol header, to assist ST to know
64  *	how much to receive, if the data is split across UART frames.
65  * @len_size: whether the length field inside the header is 2 bytes
66  *	or 1 byte.
67  * @reserve: the number of bytes ST needs to reserve in the skb being
68  *	prepared for the protocol driver.
69  */
70 struct st_proto_s {
71 	enum proto_type type;
72 	long (*recv) (void *, struct sk_buff *);
73 	unsigned char (*match_packet) (const unsigned char *data);
74 	void (*reg_complete_cb) (void *, int data);
75 	long (*write) (struct sk_buff *skb);
76 	void *priv_data;
77 
78 	unsigned char chnl_id;
79 	unsigned short max_frame_size;
80 	unsigned char hdr_len;
81 	unsigned char offset_len_in_hdr;
82 	unsigned char len_size;
83 	unsigned char reserve;
84 };
85 
86 extern long st_register(struct st_proto_s *);
87 extern long st_unregister(struct st_proto_s *);
88 
89 
90 /*
91  * header information used by st_core.c
92  */
93 
94 /* states of protocol list */
95 #define ST_NOTEMPTY	1
96 #define ST_EMPTY	0
97 
98 /*
99  * possible st_states
100  */
101 #define ST_INITIALIZING		1
102 #define ST_REG_IN_PROGRESS	2
103 #define ST_REG_PENDING		3
104 #define ST_WAITING_FOR_RESP	4
105 
106 /**
107  * struct st_data_s - ST core internal structure
108  * @st_state: different states of ST like initializing, registration
109  *	in progress, this is mainly used to return relevant err codes
110  *	when protocol drivers are registering. It is also used to track
111  *	the recv function, as in during fw download only HCI events
112  *	can occur , where as during other times other events CH8, CH9
113  *	can occur.
114  * @tty: tty provided by the TTY core for line disciplines.
115  * @tx_skb: If for some reason the tty's write returns lesser bytes written
116  *	then to maintain the rest of data to be written on next instance.
117  *	This needs to be protected, hence the lock inside wakeup func.
118  * @tx_state: if the data is being written onto the TTY and protocol driver
119  *	wants to send more, queue up data and mark that there is
120  *	more data to send.
121  * @list: the list of protocols registered, only MAX can exist, one protocol
122  *	can register only once.
123  * @rx_state: states to be maintained inside st's tty receive
124  * @rx_count: count to be maintained inside st's tty receieve
125  * @rx_skb: the skb where all data for a protocol gets accumulated,
126  *	since tty might not call receive when a complete event packet
127  *	is received, the states, count and the skb needs to be maintained.
128  * @rx_chnl: the channel ID for which the data is getting accumalated for.
129  * @txq: the list of skbs which needs to be sent onto the TTY.
130  * @tx_waitq: if the chip is not in AWAKE state, the skbs needs to be queued
131  *	up in here, PM(WAKEUP_IND) data needs to be sent and then the skbs
132  *	from waitq can be moved onto the txq.
133  *	Needs locking too.
134  * @lock: the lock to protect skbs, queues, and ST states.
135  * @protos_registered: count of the protocols registered, also when 0 the
136  *	chip enable gpio can be toggled, and when it changes to 1 the fw
137  *	needs to be downloaded to initialize chip side ST.
138  * @ll_state: the various PM states the chip can be, the states are notified
139  *	to us, when the chip sends relevant PM packets(SLEEP_IND, WAKE_IND).
140  * @kim_data: reference to the parent encapsulating structure.
141  *
142  */
143 struct st_data_s {
144 	unsigned long st_state;
145 	struct sk_buff *tx_skb;
146 #define ST_TX_SENDING	1
147 #define ST_TX_WAKEUP	2
148 	unsigned long tx_state;
149 	struct st_proto_s *list[ST_MAX_CHANNELS];
150 	bool is_registered[ST_MAX_CHANNELS];
151 	unsigned long rx_state;
152 	unsigned long rx_count;
153 	struct sk_buff *rx_skb;
154 	unsigned char rx_chnl;
155 	struct sk_buff_head txq, tx_waitq;
156 	spinlock_t lock;
157 	unsigned char	protos_registered;
158 	unsigned long ll_state;
159 	void *kim_data;
160 	struct tty_struct *tty;
161 	struct work_struct work_write_wakeup;
162 };
163 
164 /*
165  * wrapper around tty->ops->write_room to check
166  * availability during firmware download
167  */
168 int st_get_uart_wr_room(struct st_data_s *st_gdata);
169 /**
170  * st_int_write -
171  * point this to tty->driver->write or tty->ops->write
172  * depending upon the kernel version
173  */
174 int st_int_write(struct st_data_s*, const unsigned char*, int);
175 
176 /**
177  * st_write -
178  * internal write function, passed onto protocol drivers
179  * via the write function ptr of protocol struct
180  */
181 long st_write(struct sk_buff *);
182 
183 /* function to be called from ST-LL */
184 void st_ll_send_frame(enum proto_type, struct sk_buff *);
185 
186 /* internal wake up function */
187 void st_tx_wakeup(struct st_data_s *st_data);
188 
189 /* init, exit entry funcs called from KIM */
190 int st_core_init(struct st_data_s **);
191 void st_core_exit(struct st_data_s *);
192 
193 /* ask for reference from KIM */
194 void st_kim_ref(struct st_data_s **, int);
195 
196 #define GPS_STUB_TEST
197 #ifdef GPS_STUB_TEST
198 int gps_chrdrv_stub_write(const unsigned char*, int);
199 void gps_chrdrv_stub_init(void);
200 #endif
201 
202 /*
203  * header information used by st_kim.c
204  */
205 
206 /* time in msec to wait for
207  * line discipline to be installed
208  */
209 #define LDISC_TIME	1000
210 #define CMD_RESP_TIME	800
211 #define CMD_WR_TIME	5000
212 #define MAKEWORD(a, b)  ((unsigned short)(((unsigned char)(a)) \
213 	| ((unsigned short)((unsigned char)(b))) << 8))
214 
215 #define GPIO_HIGH 1
216 #define GPIO_LOW  0
217 
218 /* the Power-On-Reset logic, requires to attempt
219  * to download firmware onto chip more than once
220  * since the self-test for chip takes a while
221  */
222 #define POR_RETRY_COUNT 5
223 
224 /**
225  * struct chip_version - save the chip version
226  */
227 struct chip_version {
228 	unsigned short full;
229 	unsigned short chip;
230 	unsigned short min_ver;
231 	unsigned short maj_ver;
232 };
233 
234 #define UART_DEV_NAME_LEN 32
235 /**
236  * struct kim_data_s - the KIM internal data, embedded as the
237  *	platform's drv data. One for each ST device in the system.
238  * @uim_pid: KIM needs to communicate with UIM to request to install
239  *	the ldisc by opening UART when protocol drivers register.
240  * @kim_pdev: the platform device added in one of the board-XX.c file
241  *	in arch/XX/ directory, 1 for each ST device.
242  * @kim_rcvd: completion handler to notify when data was received,
243  *	mainly used during fw download, which involves multiple send/wait
244  *	for each of the HCI-VS commands.
245  * @ldisc_installed: completion handler to notify that the UIM accepted
246  *	the request to install ldisc, notify from tty_open which suggests
247  *	the ldisc was properly installed.
248  * @resp_buffer: data buffer for the .bts fw file name.
249  * @fw_entry: firmware class struct to request/release the fw.
250  * @rx_state: the rx state for kim's receive func during fw download.
251  * @rx_count: the rx count for the kim's receive func during fw download.
252  * @rx_skb: all of fw data might not come at once, and hence data storage for
253  *	whole of the fw response, only HCI_EVENTs and hence diff from ST's
254  *	response.
255  * @core_data: ST core's data, which mainly is the tty's disc_data
256  * @version: chip version available via a sysfs entry.
257  *
258  */
259 struct kim_data_s {
260 	long uim_pid;
261 	struct platform_device *kim_pdev;
262 	struct completion kim_rcvd, ldisc_installed;
263 	char resp_buffer[30];
264 	const struct firmware *fw_entry;
265 	unsigned nshutdown;
266 	unsigned long rx_state;
267 	unsigned long rx_count;
268 	struct sk_buff *rx_skb;
269 	struct st_data_s *core_data;
270 	struct chip_version version;
271 	unsigned char ldisc_install;
272 	unsigned char dev_name[UART_DEV_NAME_LEN + 1];
273 	unsigned flow_cntrl;
274 	unsigned baud_rate;
275 };
276 
277 /**
278  * functions called when 1 of the protocol drivers gets
279  * registered, these need to communicate with UIM to request
280  * ldisc installed, read chip_version, download relevant fw
281  */
282 long st_kim_start(void *);
283 long st_kim_stop(void *);
284 
285 void st_kim_complete(void *);
286 void kim_st_list_protocols(struct st_data_s *, void *);
287 void st_kim_recv(void *, const unsigned char *, long);
288 
289 
290 /*
291  * BTS headers
292  */
293 #define ACTION_SEND_COMMAND     1
294 #define ACTION_WAIT_EVENT       2
295 #define ACTION_SERIAL           3
296 #define ACTION_DELAY            4
297 #define ACTION_RUN_SCRIPT       5
298 #define ACTION_REMARKS          6
299 
300 /**
301  * struct bts_header - the fw file is NOT binary which can
302  *	be sent onto TTY as is. The .bts is more a script
303  *	file which has different types of actions.
304  *	Each such action needs to be parsed by the KIM and
305  *	relevant procedure to be called.
306  */
307 struct bts_header {
308 	u32 magic;
309 	u32 version;
310 	u8 future[24];
311 	u8 actions[0];
312 } __attribute__ ((packed));
313 
314 /**
315  * struct bts_action - Each .bts action has its own type of
316  *	data.
317  */
318 struct bts_action {
319 	u16 type;
320 	u16 size;
321 	u8 data[0];
322 } __attribute__ ((packed));
323 
324 struct bts_action_send {
325 	u8 data[0];
326 } __attribute__ ((packed));
327 
328 struct bts_action_wait {
329 	u32 msec;
330 	u32 size;
331 	u8 data[0];
332 } __attribute__ ((packed));
333 
334 struct bts_action_delay {
335 	u32 msec;
336 } __attribute__ ((packed));
337 
338 struct bts_action_serial {
339 	u32 baud;
340 	u32 flow_control;
341 } __attribute__ ((packed));
342 
343 /**
344  * struct hci_command - the HCI-VS for intrepreting
345  *	the change baud rate of host-side UART, which
346  *	needs to be ignored, since UIM would do that
347  *	when it receives request from KIM for ldisc installation.
348  */
349 struct hci_command {
350 	u8 prefix;
351 	u16 opcode;
352 	u8 plen;
353 	u32 speed;
354 } __attribute__ ((packed));
355 
356 /*
357  * header information used by st_ll.c
358  */
359 
360 /* ST LL receiver states */
361 #define ST_W4_PACKET_TYPE       0
362 #define ST_W4_HEADER		1
363 #define ST_W4_DATA		2
364 
365 /* ST LL state machines */
366 #define ST_LL_ASLEEP               0
367 #define ST_LL_ASLEEP_TO_AWAKE      1
368 #define ST_LL_AWAKE                2
369 #define ST_LL_AWAKE_TO_ASLEEP      3
370 #define ST_LL_INVALID		   4
371 
372 /* different PM notifications coming from chip */
373 #define LL_SLEEP_IND	0x30
374 #define LL_SLEEP_ACK	0x31
375 #define LL_WAKE_UP_IND	0x32
376 #define LL_WAKE_UP_ACK	0x33
377 
378 /* initialize and de-init ST LL */
379 long st_ll_init(struct st_data_s *);
380 long st_ll_deinit(struct st_data_s *);
381 
382 /**
383  * enable/disable ST LL along with KIM start/stop
384  * called by ST Core
385  */
386 void st_ll_enable(struct st_data_s *);
387 void st_ll_disable(struct st_data_s *);
388 
389 /**
390  * various funcs used by ST core to set/get the various PM states
391  * of the chip.
392  */
393 unsigned long st_ll_getstate(struct st_data_s *);
394 unsigned long st_ll_sleep_state(struct st_data_s *, unsigned char);
395 void st_ll_wakeup(struct st_data_s *);
396 
397 /*
398  * header information used by st_core.c for FM and GPS
399  * packet parsing, the bluetooth headers are already available
400  * at net/bluetooth/
401  */
402 
403 struct fm_event_hdr {
404 	u8 plen;
405 } __attribute__ ((packed));
406 
407 #define FM_MAX_FRAME_SIZE 0xFF	/* TODO: */
408 #define FM_EVENT_HDR_SIZE 1	/* size of fm_event_hdr */
409 #define ST_FM_CH8_PKT 0x8
410 
411 /* gps stuff */
412 struct gps_event_hdr {
413 	u8 opcode;
414 	u16 plen;
415 } __attribute__ ((packed));
416 
417 /**
418  * struct ti_st_plat_data - platform data shared between ST driver and
419  *	platform specific board file which adds the ST device.
420  * @nshutdown_gpio: Host's GPIO line to which chip's BT_EN is connected.
421  * @dev_name: The UART/TTY name to which chip is interfaced. (eg: /dev/ttyS1)
422  * @flow_cntrl: Should always be 1, since UART's CTS/RTS is used for PM
423  *	purposes.
424  * @baud_rate: The baud rate supported by the Host UART controller, this will
425  *	be shared across with the chip via a HCI VS command from User-Space Init
426  *	Mgr application.
427  * @suspend:
428  * @resume: legacy PM routines hooked to platform specific board file, so as
429  *	to take chip-host interface specific action.
430  * @chip_enable:
431  * @chip_disable: Platform/Interface specific mux mode setting, GPIO
432  *	configuring, Host side PM disabling etc.. can be done here.
433  * @chip_asleep:
434  * @chip_awake: Chip specific deep sleep states is communicated to Host
435  *	specific board-xx.c to take actions such as cut UART clocks when chip
436  *	asleep or run host faster when chip awake etc..
437  *
438  */
439 struct ti_st_plat_data {
440 	u32 nshutdown_gpio;
441 	unsigned char dev_name[UART_DEV_NAME_LEN]; /* uart name */
442 	u32 flow_cntrl; /* flow control flag */
443 	u32 baud_rate;
444 	int (*suspend)(struct platform_device *, pm_message_t);
445 	int (*resume)(struct platform_device *);
446 	int (*chip_enable) (struct kim_data_s *);
447 	int (*chip_disable) (struct kim_data_s *);
448 	int (*chip_asleep) (struct kim_data_s *);
449 	int (*chip_awake) (struct kim_data_s *);
450 };
451 
452 #endif /* TI_WILINK_ST_H */
453